MSI ProBox23 User Guide

MSI ProBox23 Manual

Get MSI ProBox23 PDF manuals and user guides View all MSI ProBox23 manuals
Add to My Manuals
Save this manual to your list of manuals

MSI ProBox23 manual content summary:

  • MSI ProBox23 | User Guide - Page 1
    ProBox23 MS-B083 G52-B0831X1
  • MSI ProBox23 | User Guide - Page 2
    Started  How to Use this Service Manual This Service Manual is targeted for MSI-authorized dealer or service center. It provides in-depth illustration of assembling the system. Each topic may be related with each other; hence you are highly recommended to read this guide from cover to cover first
  • MSI ProBox23 | User Guide - Page 3
    system.  Use a grounded wrist strap before handling system components such as CPU, Memory, HDD, mini PCI-E card, etc.  Place system components recommended that you contact the authorized dealer or service center for any upgrade or replace service.  Acquisition of Replaceable Parts Please be
  • MSI ProBox23 | User Guide - Page 4
    System Assembly  Cover & HDD Holder Important Before you remove or install any components, make sure the system is not turned on or connected to the AC power. Step 1. Place the system horizontally on a flat and steady surface. Step 2. Unlock the two screws on the back side and keep them for later
  • MSI ProBox23 | User Guide - Page 5
    Then you can see the internal of the system. For installing CPU/ Memory module/ WIFI module/ M-SATA module, you also need to remove the HDD holder. Step 4. Unlock the three screws on the HDD holder and keep them for later use. Step 5. Remove the HDD holder carefully and set it aside for later use. 4
  • MSI ProBox23 | User Guide - Page 6
    is necessary to prevent overheating and maintain system stability. Follow the steps below to ensure correct CPU and heatsink installation. Wrong installation can damage both the CPU and the motherboard. 1. Push the load lever down to unclip it and lift to the fully open position. 2. The load
  • MSI ProBox23 | User Guide - Page 7
    3. Align the notches with the socket alignment keys. Lower the CPU straight down, without tilting or sliding the CPU in the socket. Inspect the CPU to check if it is properly seated in the socket. 4. Close and slide the load plate under the retention knob. Close and engage the load
  • MSI ProBox23 | User Guide - Page 8
    paste (or thermal tape) on the top of the CPU. This will help in heat dissipation and prevent CPU overheating. 7. Locate the CPU fan connector on the motherboard. 8. Place the heatsink on the motherboard with the fan cable facing towards the fan connector and the fasteners matching the holes on the
  • MSI ProBox23 | User Guide - Page 9
    11. Finally, attach the CPU fan cable to the CPU fan connector on the motherboard. Important  Confirm that the CPU heatsink has formed a tight seal with the CPU before booting your system.  Whenever the CPU is not installed, always protect the CPU socket pins by covering the socket with the
  • MSI ProBox23 | User Guide - Page 10
     Memory The SO-DIMM slot is intended for memory modules. 1. Locate the SO-DIMM slot. Align the notch on the memory with the key on the slot and insert the memory into the slot at a 45-degree angle. 2. Push the DIMM gently downwards until the slot clips click and lock the memory module in place. 3.
  • MSI ProBox23 | User Guide - Page 11
     Wireless LAN Card and Antenna Important The wireless LAN card has only one notch and will only fit in the right direction. Step 1. Rolling off the screw on the fixing bolt. Step 2. Insert the wireless LAN card into the slot with 45° angle. Then push it in until the golden finger on the card is
  • MSI ProBox23 | User Guide - Page 12
    only fit in the right direction. Step 1. Rolling off the screw on the fixing bolt. Step 2. Insert the mSATA card into the slot with 45° angle. Then push it in until the golden finger on the card is deeply inserted. Step 3. Press the mSATA card down and then lock the screw. 11
  • MSI ProBox23 | User Guide - Page 13
     Hard Disk Drive (HDD) Step 1. Locate the HDD holder. Step 2. Take out and press the four plastic spacers from the bigger hole on the holder to the smaller fixing hole. Step 3. Slide the HDD drive into the correct position on the holder and then fix the screws with a screwdriver. Step 4. Connect
  • MSI ProBox23 | User Guide - Page 14
    Step 5. Arrange the cables. Place the HDD holder with HDD drive to the case and fix the three screws. Step 6. Place the cover back and fix the four screws. Then the hardware setting is done. 13
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
ProBox23
MS-B083
G52-B0831X1