Mackie M2000/M3000/M4000 Spec Sheet
Mackie M2000/M3000/M4000 Manual
 |
View all Mackie M2000/M3000/M4000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Mackie M2000/M3000/M4000 manual content summary:
- Mackie M2000/M3000/M4000 | Spec Sheet - Page 1
Owner's Manual Appendix B: Technical Info M-Series Specifications Continuous Average Output Power in watts, both channels driven 20 Hz- 6 min. at 4Ω 2(1±jx) time dependent, T > 2 min. at 2Ω Transient Recovery: < 1µs for 10 dB overdrive @ 1kHz Maximum Output Offset Voltage: ±50 mV Owner's Manual 23 - Mackie M2000/M3000/M4000 | Spec Sheet - Page 2
to change these specifications at any time without notice. "Mackie." and the "Running Man" are registered trademarks of 3.5 in/88 mm 24 M-Series INTERNAL STATUS PROTECT SHORT OVER TEMP M.2000 HIGH EFFICIENCY POWER AMPLIFIER 1 OL OL -3 -3 -6 -6 -9 -9 -20 -20 MAX SIG SIG 2 MAX
-
1 -
2
 |
 |
23
Owner’s Manual
Owner’s Manual
Appendix B: Technical Info
Maximum Input Level:
9.75 volts (+22 dBu)
Rise Time (8 ohms):
< 6 µs
Slew Rate:
M•2000
Voltage Slew Rate 50V/µs
Current Slew Rate 25A/µs at 2
Ω
H-Switch Slew Rate
10-50V/µs (program dependent)
M•3000
Voltage Slew Rate 55V/µs
Current Slew Rate 27.5A/µs at 2
Ω
H-Switch Slew Rate
16-70V/µs (program dependent)
M•4000
Voltage Slew Rate 60V/µs
Current Slew Rate 30A/µs at 2
Ω
H-Switch Slew Rate
16-70V/µs (program dependent)
CMRR:
> 34 dB, 20Hz to 20kHz
Load Angle:
8(±jx) time independent at 8
Ω
4(±jx) time dependent, T > 6 min. at 4
Ω
2(1±jx) time dependent, T > 2 min. at 2
Ω
Transient Recovery:
< 1µs for 10 dB overdrive @ 1kHz
Maximum Output Offset Voltage:
±50 mV
M-Series Specifications
M•2000
M•3000
M•4000
Continuous Average Output Power in watts, both channels driven
20 Hz-20 kHz into 8 ohms per channel
325
475
650
20 Hz-20 kHz into 4 ohms per channel
525
800
1050
40 Hz-20 kHz into 2 ohms per channel
800
1200
1600
Bridge Mono: 20 Hz-20 kHz into 8 ohms
1050
1600
2100
Bridge Mono: 40 Hz-20 kHz into 4 ohms
1600
2400
3200
Maximum Output Power in watts, both channels driven
1 kHz @ 1% THD into 8 ohms per channel
400
600
800
1 kHz @ 1% THD into 4 ohms per channel
650
1000
1300
1 kHz @ 1% THD into 2 ohms per channel
1000
1500
2000
Bridge Mono: 1 kHz @ 1% THD into 8 ohms
1300
2000
2600
Bridge Mono: 1 kHz @ 1% THD into 4 ohms
2000
3000
4000
Note: Power ratings are specified at 120VAC (U.S. and Canada) and 240VAC (Export) line voltages.
The M-Series power amplifiers draw large amounts of current from the AC line with continuous sine wave testing. Accurate mea-
surement of power requires a steady and stable AC supply. This means the line impedance must be very low to insure that the peak
AC line voltage does not sag to less than 97% of its value.
If driving highly reactive loads, we recommend that the limiter circuit be engaged.
Power Bandwidth (rated power into 4 ohms):
20 Hz to 20 kHz
(Output power typically –3 dB at 50 kHz. Amplifier protection cir-
cuits typically mute the output signal above 40 kHz at full power.)
Frequency Response (1 watt into 8 ohms):
< 10 Hz to 55 kHz (+0, –3 dB)
Distortion:
THD, SMPTE IMD
< 0.05% @ 8
Ω
< 0.10% @ 4
Ω
< 0.20% @ 2
Ω
Signal-to-Noise Ratio:
> 107 dB below rated power into 4 ohms
Channel Separation:
> 80 dB @ 1 kHz
Damping Factor:
> 500 (8 ohms @ 400 Hz)
Input Impedance:
24 k
Ω
balanced
12 k
Ω
balanced
Input Sensitivity:
1.23 volts (+4 dBu) for rated power into 4 ohms
Gain:
M•2000 31.4 dB (37.3 V/V)
M•3000 33.3 dB (46.0 V/V)
M•4000 34.4 dB (52.7 V/V)