Mackie SA1232 Owner's Manual

Mackie SA1232 Manual

Get Mackie SA1232 PDF manuals and user guides View all Mackie SA1232 manuals
Add to My Manuals
Save this manual to your list of manuals

Mackie SA1232 manual content summary:

  • Mackie SA1232 | Owner's Manual - Page 1
    SA1232 3-WAY ACTIVE SPEAKER SYSTEM USER'S MANUAL
  • Mackie SA1232 | Owner's Manual - Page 2
    , or its chassis damaged. 13. Servicing - The user should not attempt to service this Mackie product beyond those means described in this operating manual. All other servicing should be referred to the Mackie Service Department. 14. To prevent electric shock, do not use this polarized plug with an
  • Mackie SA1232 | Owner's Manual - Page 3
    SAFETY INSTRUCTIONS ...2 INTRODUCTION ...4 REAR PANEL DESCRIPTION ...5 HOOKUP DIAGRAM ...5 CONNECTIONS ...6 PLACEMENT ...6 AC POWER ...7 THERMAL CONSIDERATIONS ...8 SERVICE INFORMATION ...9 Warranty Service ...9 Troubleshooting ...9 Repair ...10 CARE AND MAINTENANCE ...10 SA1232 SPECIFICATIONS
  • Mackie SA1232 | Owner's Manual - Page 4
    . The amplifiers for the compression driver and The SA1232 fea- mid-range driver incorpo- tures the same horn rate a Class AB topology assembly we intro- renowned for its clarity duced in the Mackie and warmth, and for its Designs SR1530 active ability to produce the high- 3-way speaker
  • Mackie SA1232 | Owner's Manual - Page 5
    the SA1232's built-in power amplifiers. Plug the linecord into an AC socket properly configured for your particular model. PARALLEL PARALLEL PARALLEL PARALLEL To Next Speaker MAIN INPUT LOOP OUT 0dB SA1232 -15 +5 ACTIVE SOUND REINFORCEMENT SPEAKER SYSTEM CONCEIVED AND DESIGNED BY MACKIE DESIGNS
  • Mackie SA1232 | Owner's Manual - Page 6
    (+) Cold (-) Shield (Ground) XLR Pin 2 Pin 3 Pin 1 PLACEMENT The SA1232 speaker is designed to sit on the floor or stage. WARNING: The cabinet has no As with any powered components, protect them from moisture. If you are setting them up outdoors, make sure they are under cover if you expect rain
  • Mackie SA1232 | Owner's Manual - Page 7
    to the amplifiers. CAUTION: Never remove the ground pin on the power cord of the SA1232 or any other component. This is very dangerous. SA1232 systems are available in 115V and 230V AC configurations. Mackie Designs specifies a specific amount of amperage service availability for individual active
  • Mackie SA1232 | Owner's Manual - Page 8
    , we highly recommend using the SA1232 in 230 volt mode. The power supply in the SA1232 can be switched between 115 volt and 230 volt setting. Contact your local service center or Mackie Designs for information. THERMAL CONSIDERATIONS The SA1232 has three powerful built-in amplifiers capable of
  • Mackie SA1232 | Owner's Manual - Page 9
    all Mackie products returned for service (which is hardly any at all), many are coded "CND" - Could Not Duplicate- which usually means the problem lay somewhere else in the system. The following troubleshooting tips may sound obvious, but here are some things you can check: Troubleshooting No power
  • Mackie SA1232 | Owner's Manual - Page 10
    can be obtained through local dealers or distributors. If your SA1232 needs service, please follow these instructions: 1. Review the preceding troubleshooting suggestions. Please. 2. Call Tech Support at 1-800-258-6883, 7am to 5pm PST, to explain the problem in detail. They will ask you all sorts of
  • Mackie SA1232 | Owner's Manual - Page 11
    Section Number of Drivers Woofer Size Voice Coil Amplifiers Total Amplifier Power High Frequency Type Rated THD Mid Power Supply and Amplifier Thermal Protection Display LEDs Power ON, Signal Present, Limit, Thermal (Cool Down Auto Reset) Physical Height Front Width Back Width Depth Weight
  • Mackie SA1232 | Owner's Manual - Page 12
    rms amplifiers specifically designed to power the MF and HF drivers over the range of 700 Hz-3000 Hz and 3000 Hz-20 kHz respectively. The amplifiers shall be mounted on an aluminum heat sink, which shall be mounted on the rear of the speaker system, and shall be convection cooled. Dimensions 18
  • Mackie SA1232 | Owner's Manual - Page 13
    Beamwidth vs. Frequency 360 300 240 180 120 Vert BW Horz BW 60 20 100 1000 Frequency (Hz) -6 dB Beamwidth (degrees) SA1232 Directivity Index 20 Directivity Index (DI), dB 10 0 20 100 1000 Frequency (Hz) 10000 20000 10000 20000 100 10 1 10000 20000 Directivity Factor (Q) 13
  • Mackie SA1232 | Owner's Manual - Page 14
    -30 20 100 1000 Frequency (Hz) 10000 20000 0 deg 10 deg 20 deg 30 deg 40 deg SA1232 Vertical Off-Axis Frequency Response (Up) 10 0 -10 -20 -30 20 100 1000 Frequency (Hz) SA1232 Vertical Off-Axis Frequency Response (Down) 10 0 -10 -20 -30 20 100 1000 Frequency (Hz) 10000 20000
  • Mackie SA1232 | Owner's Manual - Page 15
    a shipping carton out promptly. More information on packing can be found in the Service section of this manual. Also include a note explaining exactly how to duplicate the problem, a copy of the sales receipt with price and date showing, and your return street address (no P.O. boxes or route numbers
  • Mackie SA1232 | Owner's Manual - Page 16
    design, build, sell, and support your product. ® ™ ® Mackie Designs Inc. 16220 Wood-Red Rd. NE • Woodinville, WA 98072 • USA US & Canada: 800/898-3211 Europe, Asia, Central & South America: 425/487-4333 Middle East & Africa: 31-20-654-4000 Fax: 425/487-4337 • www.mackie.com E-mail: [email protected]
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
SA1232
3-WAY ACTIVE
SPEAKER SYSTEM
USER’S MANUAL