Mackie SP2400 Instruction Manual - All

Mackie SP2400 Manual

Get Mackie SP2400 PDF manuals and user guides View all Mackie SP2400 manuals
Add to My Manuals
Save this manual to your list of manuals

Mackie SP2400 manual content summary:

  • Mackie SP2400 | Instruction Manual - All - Page 1
    Dual-Channel Program Controller/Amplifier Instruction Manual ZONE A INPUTS MASTER VOLUME 3 0 3 6 9 15 30 55 1 2 3 4 OFF ZONE B INPUTS MASTER VOLUME 3 0 3 6 9 15 30 55 1 2 3 4 OFF SP2400 MUSIC CONTROLLER A B OVERLOAD ON STATUS COMM PORT POWER 115V 60Hz FUSE 115/ T8A 220 WATTS
  • Mackie SP2400 | Instruction Manual - All - Page 2
    the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Servicing - The user should not attempt to service the SP2400 beyond those means described in this operating manual. All other servicing should be referred to the Mackie Service
  • Mackie SP2400 | Instruction Manual - All - Page 3
    2. INTRODUCTION The SP2400 is a microprocessor-based dualchannel music controller with two built-in power amplifiers designed Zone A or Zone B, or over the entire system when manually operated with a switch connected to the PAGING MIC CONTROL connector. Each zone is equipped with an input for an
  • Mackie SP2400 | Instruction Manual - All - Page 4
    clockwise to reduce the threshold. Rotate the control counterclockwise to increase the threshold. ZONE A INPUTS MASTER VOLUME 3 0 3 6 9 15 30 55 1 2 3 4 OFF ZONE B INPUTS MASTER VOLUME 3 0 3 6 9 15 30 55 1 2 3 4 OFF SP2400 MUSIC CONTROLLER A B OVERLOAD ON STATUS COMM PORT POWER
  • Mackie SP2400 | Instruction Manual - All - Page 5
    115/ T8A 220 WATTS 230V 50Hz FUSE 230/ T4A 220 WATTS SP2400 MUSIC CONTROLLER SERIAL NUMBER MANUFACTURING DATE DIRECT L THE FOLLOWING ARE TRADEMARKS OR REGISTERED TRADEMARKS OF MACKIE DESIGNS INC "MACKIE.","MACKIE INDUSTRIAL", AND THE "RUNNING MAN" FIGURE. COPYRIGHT ©2000 ALL RIGHTS RESERVED
  • Mackie SP2400 | Instruction Manual - All - Page 6
    12345678 1234 1234 REMOTE MONO Remote Control + 3 0 - 3 - 6 - 9 - 15 - 30 - 55 Digital Satellite Service Jukebox Cassette or DAT Recorder CD Player To Telephone System Music-On-Hold Paging Mic 230/115V 50/60 Hz FUSE 115/T8A SP2400 MUSIC CONTROLLER SERIAL NUMBER MANUFACTURING DATE DIRECT
  • Mackie SP2400 | Instruction Manual - All - Page 7
    Service Cassette or DAT Recorder CD Player To Telephone System Music-On-Hold Paging Mic Paging Mic Control Switch A B ALL 230/115V 50/60 Hz FUSE 115/T8A SP2400 MUSIC CONTROLLER SERIAL NUMBER MANUFACTURING DATE DIRECT LL THE FOLLOWING ARE TRADEMARKS OR REGISTERED TRADEMARKS OF MACKIE
  • Mackie SP2400 | Instruction Manual - All - Page 8
    Satellite Service Jukebox Cassette or DAT Recorder CD Player Zone A Remote Control + 3 0 - 3 - 6 - 9 - 15 - 30 - 55 Paging Mic 230/115V 50/60 Hz FUSE 115/T8A SP2400 MUSIC CONTROLLER SERIAL NUMBER MANUFACTURING DATE DIRECT LL THE FOLLOWING ARE TRADEMARKS OR REGISTERED TRADEMARKS OF MACKIE
  • Mackie SP2400 | Instruction Manual - All - Page 9
    Changer Zone A Out 230/115V 50/60 Hz FUSE 115/T8A SP2400 MUSIC CONTROLLER SERIAL NUMBER MANUFACTURING DATE DIRECT LL THE FOLLOWING ARE TRADEMARKS OR REGISTERED TRADEMARKS OF MACKIE DESIGNS INC "MACKIE.","MACKIE INDUSTRIAL", AND THE "RUNNING MAN" FIGURE. COPYRIGHT ©2000 ALL RIGHTS RESERVED
  • Mackie SP2400 | Instruction Manual - All - Page 10
    using the SP2400 in a stereo application. A Digital Satellite Service (DSS) is connected to Input 1, which also serves as the music-on-hold control exclusively operates its own zone. The Paging Mic can be manually operated with the Paging Mic Control Switch, and the Paging Mic and ALL CALL control
  • Mackie SP2400 | Instruction Manual - All - Page 11
    a requirement for music-on-hold, use Input 1 for the continuous music source (i.e., satellite feed, prerecorded background music, multidisc CD player 5. Is there a manual switch for paging? Up to three switches can be connected to the SP2400 PAGING MIC CONTROL to manually engage the paging microphone
  • Mackie SP2400 | Instruction Manual - All - Page 12
    as Belden 8451, 9451, or equivalent. The lower the nominal capacitance of the wire, the more distance you can have between the remote control and the SP2400 before suffering transmission losses. Strip the wire back about 1/4 inch, insert the wire as far as it will go into the appropriate hole in
  • Mackie SP2400 | Instruction Manual - All - Page 13
    3 = Data - (with +24V DC power) Note: See the instructions with the remote control for more information. Connecting the RS485 Serial Port This is a 3-pin Phoenix changed inside the SP2400. These settings should be made prior to installing the SP2400. CAUTION: These servicing instructions are for use
  • Mackie SP2400 | Instruction Manual - All - Page 14
    Jumper J6 on the Filter Board. J1 J2 D22 C40 D3 C23 U25 C54 SP2400 FILTER BOARD Q1 S1 EQ ENGAGE 3 2 EQ BYPASS 1 J6 L6 C91 L2 3 for 70V or 100V operation L10 C89 R96 R143 R121 R97 R133 R134 R136 R137 C62 SP2400 AMP BOARD JP1 C15 C9 C7 JP2 C17 C18 C8 C10 100V or 8Ω/250W 70V or
  • Mackie SP2400 | Instruction Manual - All - Page 15
    music with a relatively high crest factor. Voltage Conversion The SP2400 can be configured to operate at 115V AC or 230V AC. See Appendix C for instructions outputs. If this should occur, identify the cause of the problem and take corrective action (i.e., provide better ventilation, install a fan
  • Mackie SP2400 | Instruction Manual - All - Page 16
    instruction manual, which is the only way to fully understand how the SP2400 works. However, the Quick Start provides a quick overview so you can get the SP2400 have a music-on-hold requirement, connect a continuous music source to the "0" mark. Set the GAIN control so the meter indication is near the
  • Mackie SP2400 | Instruction Manual - All - Page 17
    . (The RS485 ports are connected internally, so an external connection between the RS485 ports on a single SP2400 is not necessary.) Each amplifier must have the same AMP ADDRESS as the amp to which the remote control is connected, with one assigned as Master and the other as Slave. Use the supplied
  • Mackie SP2400 | Instruction Manual - All - Page 18
    source. Set the AMP ADDRESS switches to different addresses to allow independent control over each zone. LOCAL or REMOTE These switches are used to select to the up position on the first SP2400. The music is then available to Input 1 on all the SP2400s connected via the EXPANSION IN/OUT connectors
  • Mackie SP2400 | Instruction Manual - All - Page 19
    2-band EQ controls. Using the of activating it manually with an external music begins to ramp up to its original volume. Note 2: When the manual switch is off, the voice-activated (VOX) control CONTROL switching. Alternatively, turn the PAGING MIC VOX control Threshold This control determines how
  • Mackie SP2400 | Instruction Manual - All - Page 20
    the ambient mic OFF (AMP ADDRESS switch #8 down). SP2400 - 20 3. Adjust the MASTER VOLUME control by pressing the Up/Down buttons so the meter indicates a minimum, the paging mic volume should be approximately the same as the music volume. 13. If the paging microphone is not loud enough to be heard
  • Mackie SP2400 | Instruction Manual - All - Page 21
    next section). The maximum distance between the remotes and the SP2400 varies, depending on the type of cable selected and the number of remote controls used. Typically, a lower wire gauge and cable capacitance allow longer distances. See the instructions with the remote control for more information
  • Mackie SP2400 | Instruction Manual - All - Page 22
    be used to interface with common third-party control systems. Contact the third-party provider or Mackie Industrial Technical Support to determine if your control system is compatible with the SP2400. Upgrading the Software From time to time, Mackie Industrial will release upgrades for the internal
  • Mackie SP2400 | Instruction Manual - All - Page 23
    IN 25 13 14 1 +15VDC (w/J3 INSTALLED) PAGING MIC CONTROL PAGING MIC (-) INPUT 4 RIGHT (-) INPUT 4 LEFT (-) GROUND INPUT 3 RIGHT (+) INPUT 3 LEFT (+) INPUT 2 RIGHT (-) INPUT 2 LEFT (-) GROUND INPUT 1 RIGHT (+) INPUT 1 LEFT (+) MACKIE INDUSTRIAL SP2400 BLOCK DIAGRAM (#01.02.01.DF) -15VDC (w/J2
  • Mackie SP2400 | Instruction Manual - All - Page 24
    12kHz ±12 dB @ 100Hz General Power Consumption 700 watts with musical program, 8 ohms per side 800 watts maximum Phantom Power 24 VDC Accessories MT-3100 SP-41R Ambient Noise Sensing Microphone Remote Control Preamplifier Section Input Levels Program Inputs: Paging Mic Input: SP2400 - 24
  • Mackie SP2400 | Instruction Manual - All - Page 25
    Industrial. Printed in the U.S.A. 6. Service Information In the event that your SP2400 should require servicing, please follow these instructions: 1. Call Mackie Industrial Tech Support at 1-888-3377404, 8 am to 5 pm PST (Monday-Friday), to verify the problem and obtain a Return Authorization (RA
  • Mackie SP2400 | Instruction Manual - All - Page 26
    OFF button to return to normal operation. Press 3 on Power Up: Paging Mic Level Adjustment • Press and hold the Input 3 button while powering up the SP2400. • Release the Input 3 button. The lowest Paging Mic level is indicated on the LED meter. • Use the Up/Down buttons to adjust the lowest Paging
  • Mackie SP2400 | Instruction Manual - All - Page 27
    that contained in the Operating Instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. Make sure the power is off and the power cord disconnected before removing the top cover to gain access to the inside of the SP2400. JUMPER INSTALLED FOR 115V BROWN
  • Mackie SP2400 | Instruction Manual - All - Page 28
    SP2400 Music Controller Mackie Industrial 16220 Wood-Red Rd. NE • Woodinville, WA 98072 • USA 888/337-7404 • Outside the U.S.: 425/487-4333 Fax: 425/487-4337 • www.mackieindustrial.com
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
SP2400 MUSIC CONTROLLER
INPUTS
INPUTS
OFF
3
0
3
6
9
15
30
55
OFF
3
0
3
6
9
15
30
55
A
B
ON
OVERLOAD
STATUS
POWER
COMM PORT
ZONE A
MASTER
VOLUME
ZONE B
MASTER
VOLUME
1
2
3
4
1
2
3
4
12345678
1234
1234
12345678
1
2
3
G
+
–
G
+
–
A
G
B
A
G
B
0
I
PHANTOM
GAIN +40dB
MIC/LINE INPUT B
PROGRAM EQ
1234
12345678
1
2
3
G
+
–
G
+
–
0
I
PHANTOM
GAIN +40dB
MIC/LINE INPUT A
PROGRAM EQ
1234
PARALLEL
INPUTS
CONTROL
ZONE
A
ZONE
B
GROUND
ALL CALL
GAIN +40dB
PHANTOM
DIRECT
L
R
OUTPUT
PROGRAM INPUTS
1
2
3
4
PRIORITY
MONO
STEREO
LOCAL
1
2
3
4
REMOTE
1
2
3
4
ON
SP2400
MUSIC CONTROLLER
HIGH
U
+12
–12
U
+12
–12
LOW
GAIN
+
-
HIGH 12k
FREQ
MID
LOW 80Hz
U
+15
–15
U
+15
–15
U
+15
–15
1K
3K
400
8k
250
HIGH
U
+12
–12
U
+12
–12
LOW
GAIN
+
-
+
-
AMP ADDRESS
ZONE B
RS485
REMOTE
AMBIENT
MIC
MIC
VOX
AMP IN
PRE OUT
HIGH 12k
FREQ
MID
LOW 80Hz
U
+15
–15
U
+15
–15
U
+15
–15
1K
3K
400
8k
250
HIGH
U
+12
–12
U
+12
–12
LOW
GAIN
+
-
+
-
ZONE A
AMP IN
PRE OUT
PAGING MIC
EXPANSION IN
EXPANSION OUT
THE FOLLOWING ARE TRADEMARKS OR REGISTERED TRADEMARKS OF MACKIE DESIGNS INC
"MACKIE.","MACKIE INDUSTRIAL", AND THE "RUNNING MAN" FIGURE.
COPYRIGHT ©2000 ALL RIGHTS RESERVED
AMP ADDRESS
RS485
REMOTE
AMBIENT
MIC
PAGING
MIC
VOX
PAGING
CONCEIVED, DESIGNED, AND MANUFACTURED BY MACKIE DESIGNS INC. • WOODINVILLE • WA • MADE IN USA • FABRIQUE AU USA
STEREO RIGHT
STEREO LEFT
115V 60Hz FUSE 115/ T8A
220 WATTS
230V 50Hz FUSE 230/ T4A 220 WATTS
CAUTION:
TO REDUCE THE
RISK OF FIRE
REPLACE WITH SAME TYPE FUSE AND RATING
OUTPUT SUITABLE
FOR CLASS 2 WIRING
100/70V/8
+
–
OUTPUT SUITABLE
FOR CLASS 2 WIRING
100/70V/8
+
–
SERIAL NUMBER
MANUFACTURING DATE
G
+
–
SP2400 Dual-Channel
Program Controller/Amplifier
Instruction Manual