Home » Makita Manuals » Tools » Makita 5402NA » Manual Viewer

Makita 5402NA Owners Manual

Makita 5402NA Manual

View all Makita 5402NA manuals

Add to My Manuals
Save this manual to your list of manuals

Makita 5402NA manual content summary:

Makita 5402NA | Owners Manual - Page 1
Circular Saw Equipped with Electric Blade Brake 415 mm (16 - 5/16") MODEL 5402NA 001963 INSTRUCTION MANUAL WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. www.makitatools.com
Makita 5402NA | Owners Manual - Page 2
Model Blade diameter Max. cutting capacities at 90° at 45° No load speed (RPM) Overall length Net weight 5402NA 415 mm (16-5/16") 158 mm (6-3/16") 106 mm (4-3/16 all instructions. Failure to follow all instructions listed below, plug in any way. Do not use any adaptor plugs. Check with a qualified
Makita 5402NA | Owners Manual - Page 3
of moving parts, breakage of parts, and any other condition that may affect the tools operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. 22. Use only accessories that are recommended by the manufacturer for your model. Accessories that
Makita 5402NA | Owners Manual - Page 4
24. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance instructions may create a risk of electric shock or injury. USE PROPER EXTENSION CORD: Use only three-wire
Makita 5402NA | Owners Manual - Page 5
or familiarity with product (gained from repeated use) replace strict adherence to circular saw safety rules. If you use this tool unsafely or incorrectly, you can suffer serious personal injury. 1. DANGER! Keep hands away from cutting area and blade. Keep your second hand on auxiliary handle
Makita 5402NA | Owners Manual - Page 6
. 2 Do not support board or panel away from the cut. Do not use dull or damaged blade. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and KICKBACK. Keep blade sharp and clean. Gum and wood pitch hardened on blades slows saw and increases potential
Makita 5402NA | Owners Manual - Page 7
firmly to prevent loss of control which Fig. 4 A typical illustration of proper hand support, workpiece support, and supply cord routing. 16. Place the wider portion of the saw base on that part of the workpiece which is solidly supported, not on the section that will fall off when the cut is made
Makita 5402NA | Owners Manual - Page 8
a cut, be sure that the lower (telescoping) guard has closed and the blade has come to a complete stop. 19. Some material contains chemicals which may be rules stated in this instruction manual may cause serious personal injury. SYMBOLS USD101-2 The followings show the symbols used for tool. V
Makita 5402NA | Owners Manual - Page 9
2. Lock 3. Lock lever 001966 Blade steady device In general way, use the lock lever by setting it in locked position. To lock the lock lever, push it down and turn it 90° counterclockwise. To release the lock lever, turn it 90° clockwise. When you replace a saw blade, release the lock lever. 3 9
Makita 5402NA | Owners Manual - Page 10
align the A position on the front of the base B A with your cutting line. For 45° blade brake. If the tool consistently fails to quickly stop blade after switch trigger release, have tool serviced at a Makita service center. The blade brake system is not a substitute for lower guard. NEVER USE
Makita 5402NA | Owners Manual - Page 11
BOLT CLOCKWISE SECURELY. After installing the blade, lock the lock lever. When changing blade, make sure to also clean upper and lower blade guards of accumulated sawdust. Such efforts do not, however, replace the need to check lower guard operation before each use. CAUTION: • The inner flange has
Makita 5402NA | Owners Manual - Page 12
firmly. The tool is provided with both a front grip and rear handle. Use both to best grasp the tool. If both hands are holding saw, they cannot be cut by the blade. Set 2 the base on the workpiece to be cut without the blade making any contact. Then turn the tool on and wait until the
Makita 5402NA | Owners Manual - Page 13
) 1 2 This adjustment has been made at the factory. But if it is off, adjust the adjusting screw with the hex wrench while squar- ing the blade with the base using a triangular rule, try square, etc. 1. Adjusting screw 2. Base 1 001978 2 1. Trianglar rule 2. Hex wrench 13
Makita 5402NA | Owners Manual - Page 14
or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESSORIES CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments
Makita 5402NA | Owners Manual - Page 15
Memo 15
Makita 5402NA | Owners Manual - Page 16
Memo 16
Makita 5402NA | Owners Manual - Page 17
Cut Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 First-Class Postage Required Post Office will not deliver without proper postage. Fold 17
Makita 5402NA | Owners Manual - Page 18
From Friend Previous Usage Other ( ) 2. Use of the product is intended for: Construction Trade Industrial Maintenance Home Maintenance Hobby Other ( ) 4. Most favored points are: Design Features Size Price Makita Brand Repair Service Durability Power Other ( ) 5. Any comments
Makita 5402NA | Owners Manual - Page 19
When you need service: Send complete tool (prepaid) to one of the Makita Factory Service Centers listed, or to an Authorized Makita Service Center. Be sure to attach a letter to the outside of the carton detailing the problem with your tool. Date Purchased Dealer's Name & Address Model No. Serial
Makita 5402NA | Owners Manual - Page 20
Makita's Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT.