Makita 9820-2 Owners Manual
Makita 9820-2 Manual
 |
View all Makita 9820-2 manuals
Add to My Manuals
Save this manual to your list of manuals |
Makita 9820-2 manual content summary:
- Makita 9820-2 | Owners Manual - Page 1
Sharpener 200 mm (7-718") MODEL 9820-2 INSTRUCTION MANUAL SPECIFICATIONS Wheel size 200 m m x 25 mm x 75 m m (7-7/8" x 1" x 3") No load speed 560 R/min. Overall length 390 mm (15-3/8") Net weight 1 1 kg (24.3 Ibs) - Makita 9820-2 | Owners Manual - Page 2
WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 15. DISCONNECT TOOLS before servicing; when changing accessories such as blades, bits, cutters, and the like. 16. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make - Makita 9820-2 | Owners Manual - Page 3
the owner's manual for recommended accessories. The use of improper accessories may cause risk of injury to persons. 18. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted. 19. CHECK DAMAGED PARTS. Before further use of the tool - Makita 9820-2 | Owners Manual - Page 4
stripes is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the the grounding instructions are not completely understood, or if in doubt as t o whether the tool is properly grounded. This tool is intended for use on a - Makita 9820-2 | Owners Manual - Page 5
For Your Own Safety Read Instruction Manual Before Operating Grinder 1. Wear eye protection. 2. Use grinding wheel suitable for speed of grinder. 3. Replace cracked wheel immediately. 4. Always use guards and eye shields. 5. Do not overtighten wheel nut. 6. Use only flanges furnished with the - Makita 9820-2 | Owners Manual - Page 6
HOW TO USE Replacing grinding wheel Use the wrench provided to release the grinding wheel by turning the installation screw counterclockwise. To install the grinding wheel, follow the removal procedure in reverse. Adjusting wheel guard The top of the wheel guard should be 1 mm (approx. 1/3") below - Makita 9820-2 | Owners Manual - Page 7
Loosen the pole fastening screws and lift off the sharpening platform guide. To install the sharpening platform guide, follow the removal procedure in reverse. Adjusting sharpening platform guide In using the sharpening platform guide to sharpen blade/knife, adjust the angle adjustment screw to the - Makita 9820-2 | Owners Manual - Page 8
mm (1/32") when turned counterclockwise. Tilt the sharpening platform guide slightly with right side downward so that the blade contacts the right side surface of the grinding wheel. Adjusting sharpening holder I The sharpening holder horizontal (forward) adjust screws should be unscrewedto allow - Makita 9820-2 | Owners Manual - Page 9
far right. Slide the holder to the right across the sharpening platform guide. Screw in the left-hand forward adjust screw until the left upper edge of the blade contacts the grinding wheel. Now use all four fastening screws to secure the blade on the horizontal. Installingcoolant reservoir (Tank - Makita 9820-2 | Owners Manual - Page 10
. r Turn the marking to the horizontal posi- tion to stop the coolant flow. NOTE : Adjust the coolant flow adequately. If the debris from the grinding wheel and the blade is washed away by the coolant, the coolant flow is excessive. Draining used coolant The used coolant drains out through the drain - Makita 9820-2 | Owners Manual - Page 11
pressure (about 5 kg; about 11 Ibs) on it. CAUTION : Always use sharpening platform guide or guide assembly (optional accessory) when sharpening bladdknife. Remove some stock from the tip to the heel in relation to the original grinding angle so as to create a better cutting edge. 1 Take down - Makita 9820-2 | Owners Manual - Page 12
Sharpening power planer blades Sharpen your planer blades to a 40" angle. Power planer blade CAUTION : *Clean and dry the tool after operation. 0 Be sure that the tool is switched off, unplugged and drained before attempting to move the tool. 12 - Makita 9820-2 | Owners Manual - Page 13
injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Grinding wheels Wrench Part No. 341 391 - 3 Size (mm) I Grit I Part No. 200x25~75 (7-7/8" x 1" x 3") 741074-9 Guide assembly (Sharpening platform guide) For sharpening scissors or knife - Makita 9820-2 | Owners Manual - Page 14
200 mm (7-7/8") SHARPENER Model 9820-2 Aug.-02-84 US Note: The switch and other part configurations may differ from country to country. 14 - Makita 9820-2 | Owners Manual - Page 15
MODEL 9820.2 SDDESCRIPTION ,":,DESCRIPTION Sep-19-'84 US MACHINE MACHINE 1 1 Knob 65 2 1 Vinyl Tube 3 1 Wheel Cover 4 2 Pan Head Screw M5x20 lfOn Paper Pan Head Screw M4x8 IWith Washerl Screw M6x71 Blade Holder 400 Screw M6x18 Blade Set Plate 400 Note The Switch and Other pari - Makita 9820-2 | Owners Manual - Page 16
Makita's Factory or Authorized ServiceCenters. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
 |
 |
Sharpener
Wheel size
200
mm
x
25
mm
x
75
mm
(7-7/8"
x
1"
x
3")
200
mm
(7-718")
MODEL
9820-2
No load speed
Overall length
Net weight
560
R/min.
390
mm
(1
5-3/8")
11
kg (24.3
Ibs)
INSTRUCTION MANUAL
SPECIFICATIONS