Makita JN1601 Owners Manual

Makita JN1601 Manual

Get Makita JN1601 PDF manuals and user guides View all Makita JN1601 manuals
Add to My Manuals
Save this manual to your list of manuals

Makita JN1601 manual content summary:

  • Makita JN1601 | Owners Manual - Page 1
    MODEL JN1601 INSTRUCTION MANUAL DOUBLE INSULATION SPECIFICAT10NS Max. cutting capacities Mild steel Stainless Aluminum Min. cutting radius I I Strokes from country to country. WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
  • Makita JN1601 | Owners Manual - Page 2
    GENERAL SAFETY RULES (For All Tools) WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS READ ALL INSTRUCTIONS. WORK AREA 1. Keep your work area clean and well lit.
  • Makita JN1601 | Owners Manual - Page 3
    personnel could result in a risk of injury. 24. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury. 3
  • Makita JN1601 | Owners Manual - Page 4
    the workpiece immediately after operation; they may be extremely hot and could burn your skin. SAVE THESE INSTRUCTIONS. SYMBOLS The followings show the symbols used for tool. volts amperes herts hours minutes alternating current direct current no load speed alternating or direct
  • Makita JN1601 | Owners Manual - Page 5
    loosen the bolts which secure the die. Remove the die from the die holder. Use the hex wrench to loosen the screw which secures the punch. Pull the punch out of the punch holder, A Hex wrench Bolts I I To install the punch and die, insert the punch into the punch holder so that the notch in the
  • Makita JN1601 | Owners Manual - Page 6
    : 1. Loosen the lock nut with the wrench provided. 2. Pull the die holder slightly and depress lightly while turning it to the desired position. The die holder will lock into one of the positive stop positions as desired. 3. Turn the die holder slightly to make sure that it is positively locked into
  • Makita JN1601 | Owners Manual - Page 7
    the die holder serve as the thickness gauge for allowable cutting thick- ness. Cutting line The notch in the die holder Gauge for cutting stainless: 1.2 mm Gauge for cutting mild steel: 1.6 mm Notch Pre-lubrication Coat the cutting line with machine oil to increase the punch and die service
  • Makita JN1601 | Owners Manual - Page 8
    Cuttingthe corrugated or trapezoidalsheet metals Set the die position so that the die faces the cutting direction either when cutting a t an angle or perpendicular to grooves in corrugated or trapezoidal sheet metals. Always hold the tool body parallel
  • Makita JN1601 | Owners Manual - Page 9
    the new ones and secure the brush holder caps. Limit mark ,-Brush holder cap Screwdriver / To maintain product SAFETY AND RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 9
  • Makita JN1601 | Owners Manual - Page 10
    use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Die Part No. A-I 5051 *Punch Part No. A-I 5067 *Hex wrench Part
  • Makita JN1601 | Owners Manual - Page 11
    NIBBLER Model JN1601 Nav.--29-'94 EN d Note: The switch, noise suppressor and other part configurations may differ from country to country. 11
  • Makita JN1601 | Owners Manual - Page 12
    and other part specifications may differ from country to country stopper Pin 6 Ram Punch Holder Hex Socket Head Bolt M 5 x 8 Punch Dle One Holder Hex Socket Head Makita's Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
MODEL
JN1601
Max. cutting capacities
Mild
steel
Stainless
Aluminum
1.6
mm
1.2
mm
2.5
mm
(lil6")
13/64")
(3132")
INSTRUCTION MANUAL
Strokes
Overall
Net
Min. cutting radius
Outslde edge
Inside edge
per
minute
length
weight
50
mm
45
mm
261
mm
1.6
kg
12")
(1-25132")
2r200
(10-114")
(3.5
Ibs)
DOUBLE
INSULATION
SPEC
I
FICAT1
0
N
S
I
I
I
* Manufacturer reserves the right to change specifications without notice.
* Note: Specifications may differ from country to country.
WARNING: For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.