Makita JN3200 Owners Manual

Makita JN3200 Manual

Get Makita JN3200 PDF manuals and user guides View all Makita JN3200 manuals
Add to My Manuals
Save this manual to your list of manuals

Makita JN3200 manual content summary:

  • Makita JN3200 | Owners Manual - Page 1
    MODEL JN3200 INSTRUCTION MANUAL DOUBLE INSULATlO N SPECIFlCAT10NS Max. cutting capacities Min. cutting radius Mild steel Stainless Outside edge Inside edge 3.2 mm (118") 2 5 mm 128 mm 13/32',) (5-1116") (142-
  • Makita JN3200 | Owners Manual - Page 2
    Don't wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves and non-skid footwear are recommended when working outdoors. Wear instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have repaired by authorized service
  • Makita JN3200 | Owners Manual - Page 3
    More Not More Than Than 0- 6 18 6 - 10 18 10 - 12 16 12 - 16 14 AWG 16 16 part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual. Have defective switches replaced by authorized service
  • Makita JN3200 | Owners Manual - Page 4
    that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY t o the user - as well as damage t o the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate rating
  • Makita JN3200 | Owners Manual - Page 5
    tensile strength of the material itself. The groove on the die holder acts as a thickness gauge. Do not attempt t o cut any material which will not by holding the nibbler upright and applying gentle pressure in the cutting direction. For clean cutting apply oil to the punch about every 10 meters (32
  • Makita JN3200 | Owners Manual - Page 6
    lock nut and tap the handle lightly with a hammer t o loosen the nut. .Then, take off the die holder and use the wrench provided t o remove the screw to the left (counterclockwise), now remove the punch. Note : When installing the screw and lock nut, be sure to tighten securely. If they become loose
  • Makita JN3200 | Owners Manual - Page 7
    Maintenance After using, clean out the die area, lubricate with machine oil, run for a minute or two and store the tool. Punch & die service l i f e Replace or sharpen punch and die after cutting the lengths indicated in the accompanying table. Their life, of course, depends upon the thickness of
  • Makita JN3200 | Owners Manual - Page 8
    replace both brushes at the same time. a 0 \ Carbon brush q To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
  • Makita JN3200 | Owners Manual - Page 9
    h y o u r Makita t o o l specified in this manual. The use of any other accessories or attachments might present a risk of injury t o persons. The accessories or attachments should be used only in the proper and intended manner. Punch Part No. 792291-4 Die Part No. 792292-2 Washer Part No. 341796
  • Makita JN3200 | Owners Manual - Page 10
    NIBBLER Model JN3200 Sep.--22--'94 US Note: The switch and other part configurations may differ from country to country. 10
  • Makita JN3200 | Owners Manual - Page 11
    MODEL JN320O ,":,DESCRIPTION 1 4 Pan Hedd Screw M 5 x 5 0 lWith Washer) 2 1 Gear Housing 3 1 Flat Washer 1 2 4 1 Rod 5 1 Needle Bearing 2020 6 1 Crank Shaft 7 1 Spur Gear 4 4 8 1 Flat Washer 10 9 1 Gear Housing Cover 10 1 Ball Bearinq 608LB 11 1 Fan 10 Punch Die
  • Makita JN3200 | Owners Manual - Page 12
    during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita's Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace) without charge. This Warranty does not
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
MODEL
JN3200
Max. cutting capacities
Mild steel
Stainless
3.2
mm
2 5
mm
(118")
13/32',)
INSTRUCTION MANUAL
AMPS
Strokes
Overall
Net
Power
Min. cutting radius
Outside edge
Inside edge
"I
per
minute
length
we'ght
suppl~
cord
128
mm
120
mm
1,300
215
mm
3.4
kg
2.5
m
(5-1116")
(4-314")
A
(8-112")
(7.5
Ibs)
(8.2
ft.)
DOUBLE
INSU
LATlO
N
SPEC
I
Fl
CAT1
0
N
S