Makita MAC5200 Owners Manual

Makita MAC5200 Manual

Get Makita MAC5200 PDF manuals and user guides View all Makita MAC5200 manuals
Add to My Manuals
Save this manual to your list of manuals

Makita MAC5200 manual content summary:

  • Makita MAC5200 | Owners Manual - Page 1
    OWNERS MANUAL FOR Oil Lubricated Air Compressor MODEL No MAC5200 SPECIFICATION CHART Model # Horsepower SCFM @ 40 PSIG SCFM @ 90 PSIG Cut-In Pressure Cut-Out Pressure Bore Stroke Voltage -Single Phase Motor RPM Amperage @ max pressure Tank Size CSA/US Listed MAC5200 3 6.9 6.5 110 PSI 140 PSI 47
  • Makita MAC5200 | Owners Manual - Page 2
    TABLE OF CONTENTS SAFETY INSTRUCTIONS 3 Warning Chart 3 GLOSSARY 7 DUTY CYCLE 7 GENERAL INFORMATION ON-RECEIPT INSPECTION 7 STORAGE 8 DESCRIPTION OF OPERATION 8 INSTALLATION and BREAK-IN PROCEDURES 9 Location Of the Air Compressor 9 Lubrication and Oil 9 Initial Start Up Procedure 10
  • Makita MAC5200 | Owners Manual - Page 3
    air compressor could lead to serious injury to you or others. • Review and understand all instructions and warnings in this manual. • Become familiar with the operation and controls of the air compressor fire extinguisher. • Do not operate machine with missing, broken, or unauthorized parts. Page 3
  • Makita MAC5200 | Owners Manual - Page 4
    . • Unauthorized modifications to the pressure switch, safety valve, or any other components, which control tank pressure. • Follow the equipment manufacturers recommendation and never exceed the maximum allowable pressure rating of attachments. Never use the compressor to inflate small lowpressure
  • Makita MAC5200 | Owners Manual - Page 5
    other components. • Sprayed materials such as paint, paint • Never inhale air from the compressor, either directly or from a breathing device connected to the compressor. Work in an area equipped with good cross ventilation. • Read and follow the safety instructions provided on the label or safety
  • Makita MAC5200 | Owners Manual - Page 6
    (continued) solvents, paint remover, insecticides, weed killers, etc., contain harmful vapors and poisons. • Breathing compressor or sprayed materials vapor Parts The compressor cycles • Always unplug the automatically when the compressor and pressure switch is in the release air pressure on
  • Makita MAC5200 | Owners Manual - Page 7
    compressor. When oil is changed regularly, it will give you long, trouble-free life. Your air compressor can be used for operating paint spray guns, air tools, caulking guns, grease guns, air brushes, sandblaster, inflating tires or spraying weed killers, insecticides, etc. An air pressure regulator
  • Makita MAC5200 | Owners Manual - Page 8
    Store the air compressor in a clean and dry location. DESCRIPTION OF OPERATION DRAIN VALVE: The drain valve is located at the bottom of the air tank and is used to drain condensation at the end of each use. MOTOR THERMAL OVERLOAD PROTECTOR: The electric motor has a manual thermal overload protector
  • Makita MAC5200 | Owners Manual - Page 9
    of each particular accessory, the outlet regulated air pressure may have to be adjusted while you are operating the accessory. INSTALLATION AND BREAK-IN PROCEDURES LOCATION OF THE AIR COMPRESSOR Locate the air compressor in a clean, dry and well-ventilated area. The air filter must be kept clear of
  • Makita MAC5200 | Owners Manual - Page 10
    and pistons, and to seat the piston rings. 4.Close air receiver drain valve. Your compressor is now ready for use. Extension Cords To avoid voltage drop, power loss, and overheating of the motor, use extra air hose instead of an extension cord. Low voltage can cause damage to the motor. If an
  • Makita MAC5200 | Owners Manual - Page 11
    not operate the compressor near the spray area. When you are finished: 6. Set the pressure switch lever to "OFF". 7. Using the air tool or accessory, bleed the tank pressure down to zero. 8. Remove the air tool or accessory. 9. Drain water from air tank by opening drain cock valve on bottom of tank
  • Makita MAC5200 | Owners Manual - Page 12
    /or vibration. 3. Manually check all safety valves to make sure they are operating properly. 4. Inspect air filter, replace if necessary. 5. Inspect air lines and fittings for leaks; correct as necessary. Each year of operation or if a problem is suspected: • Check condition of air compressor pump
  • Makita MAC5200 | Owners Manual - Page 13
    Allow oil to drain completely. 2.Replace the oil drain plug (The use of a sealing compound or Teflon tape to avoid leakage is recommended.) 3.Refill with the recommended oil to the proper level. SERVICE INSTRUCTIONS Air Filter - Inspection and Replacement: • Keep the air filter clean at all times.
  • Makita MAC5200 | Owners Manual - Page 14
    TROUBLESHOOTING GUIDE PERFORMING REPAIRS MAY EXPOSE VOLTAGE SOURCES, MOVING PARTS OR COMPRESSED AIR SOURCES. PERSONAL INJURY MAY OCCUR. PRIOR TO ATTEMPTING ANY REPAIRS, UNPLUG THE COMPRESSOR AND BLEED OFF TANK AIR PRESSURE. PROBLEM CAUSE Excessive tank pressure safety valve pops off. Defective
  • Makita MAC5200 | Owners Manual - Page 15
    compressor in the paint spray area. • Plug unit into "live" electrical outlet. • Check and replace if required. • Remove and clean, or replace. • Tighten fittings. (See Air Leaks section of troubleshooting guide). Motor will not run. • Motor overload protection switch has tripped. • Tank pressure
  • Makita MAC5200 | Owners Manual - Page 16
    compressor on its own branch circuit. • Bleed the line by pushing the lever on the pressure switch to the "off" position; if the valve does not open, replace it. Regulator knob has continuous air leak. Regulator will not shut off at air outlet. Dirty or damaged regulator internal parts. Replace
  • Makita MAC5200 | Owners Manual - Page 17
    ) 541-4776 Customer Record When you need service: Send complete tool (prepaid) to one of the Makita Factory Service Centers listed, or to an Authorized Makita Service Center. Be sure to attach a letter to the outside of the carton detailing the problem with your tool. Date Purchased Dealer's Name
  • Makita MAC5200 | Owners Manual - Page 18
    examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry Makita's Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair, (or at our option, replace
  • Makita MAC5200 | Owners Manual - Page 19
    of the product is intended for: Construction Trade Industrial Maintenance Home Maintenance Hobby Other ( ) 5. Any comments: 3. How 4. Most favored points are: Design Repair Service Features Durability Size Power Price Other ( ) Makita Brand DATE PURCHASED MONTH DAY YEAR INTL.
  • Makita MAC5200 | Owners Manual - Page 20
    Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 First Class Postage Required Post Office will not deliver without proper postage
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
OWNERS MANUAL FOR
Oil Lubricated Air Compressor
MODEL No
MAC5200
SPECIFICATION CHART
Model #
MAC5200
Horsepower
3
SCFM @ 40 PSIG
6.9
SCFM @ 90 PSIG
6.5
Cut-In Pressure
110 PSI
Cut-Out Pressure
140 PSI
Bore
47 mm
Stroke
44 mm
Voltage -Single Phase
120
Motor RPM
3420
Amperage @ max pressure
13.8
Tank Size
5.2 Gallon
CSA/US Listed
Yes
Minimum Circuit Requirement: 15 AMPS
*A circuit breaker is preferred.
Use only a fuse or circuit
breaker that is the same rating as the branch circuit the air
compressor is operated on.
If the air compressor is connected
to a circuit protected by fuses, use time delay fuses.
IMPORTANT — Read the Safety Guidelines and ALL
instructions carefully before operating.
www.makitatools.com