Marantz AV7005 AV7005 User Manual - English - Page 56
Set up speakers
View all Marantz AV7005 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 56 highlights
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Set up speakers This section provides the setup methods of speaker systems other than the 7.1-channel system (with surround back speakers). For the setup methods of the 7.1-channel system with surround back speakers, see "Simple version", "Set up speakers (Audyssey® Auto Setup)" (vpage 8) of "Simple version". First install and connect the speakers to this unit. Before Auto Setup measurement, the settings shown below can be made. • Changing the amplifier assignment (Amp Assign) The signal output from the UNBALANCED and BALANCED PRE OUT SBL/SBR terminals of this unit can be switched to match your speaker environment. (vpage 52 "Set up "Amp Assign""). • Setting the channels to be used (Channel Select) If channels that are not to be used are set in advance, measurement for the set channels is skipped, and measuring time can be reduced (vpage 52 "Set up "Channel Select""). nnAudio output from each PRE OUT terminal PRE OUT Channel UNBALANCED PRE OUT terminal FL/FR C SW1/SW2 SL/SR SBL/SBR BALANCED PRE OUT terminal FL/FR C SW1/SW2 SL/SR SBL/SBR Audio Output Front A Center Subwoofer 1 / Subwoofer 2 Surround Surround Back* *The output audio differs depending on the "Amp Assign" settings. HL/HR WL/WR --- --- Front Height / Front B Front Wide 1 Set up the remote control unit nn Set up the operation mode Press AMP to set the remote control unit to amplifier operation mode. 2 Connect the setup microphone. Press AMP When the setup microphone is connected, the following screen is displayed. AUTO SETUP AUDYSSEY AUTO SETUP MultEQ XT STEP1 Preparation Connect the speakers and place them according to the recommendations in the manual. Set the following items if necessary. Amp Assign Channel Select Auto Setup Start [1/6] Start Auto Setup ENTER Enter RETURN Cancel 3 Set up "Amp Assign" Use ui to select "Amp Assign", and then press ENTER. AUTO SETUP AUDYSSEY AUTO SETUP MultEQ XT STEP1 Preparation Connect the speakers and place them according to the recommendations in the manual. Set the following items if necessary. Amp Assign Channel Select Auto Setup Start [1/6] ENTER Enter RETURN Cancel Set use of surround back ch. for your system 4 Use o p to select the configuration of the connected speakers, and then press RETURN. Normal ZONE2 Set when using surround back, front height or front wide speakers. In this case, go to step 5. Set for connecting the speakers for ZONE2. ZONE3 Set for connecting the speakers for ZONE3. SPKR-C Set for connecting the tweeter of the front speaker to the UNBALANCED and BALANCED PRE OUT SBL/SBR terminals of the power amp, and the woofer of the front speaker to the FL/FR terminals. around items indicate the settings. 5 Set up "Channel Select" Use ui to select "Channel Select", and then press ENTER. AUTO SETUP AUDYSSEY AUTO SETUP MultEQ XT STEP1 Preparation Connect the speakers and place them according to the recommendations in the manual. Set the following items if necessary. Amp Assign Channel Select Auto Setup Start [1/6] ENTER Enter RETURN Cancel Skip unused ch's measurement for timesaving 6 Use ui to select a channel. Subwoofer Surround Back Front Height Front Wide Select for no subwoofers to be used. In this case, go to step 7. Select for no surround back speakers to be used. In this case, go to step 8. • "Surround Back" can be set when "Amp Assign" is set to "Normal". Select for no front height speakers to be used. In this case, go to step 9. • "Front Height" can be set when "Amp Assign" is set to "Normal". Select for no front wide speakers to be used. In this case, go to step 9. • "Front Wide" can be set when "Amp Assign" is set to "Normal". 7 GWhen "Subwoofer" is selected in step 6H Use o p to select the item. Measure Set for measuring a subwoofer. Skip Set for no measuring of a subwoofer. 52 Remote control operation buttons Move the cursor (Up/Down/Left/Right) Confirm the setting Return to previous menu