Marantz AV7005 AV7005 User Manual - English - Page 78

ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Audio/Video Adjust nnAudyssey Settings Default settings are underlined. Set MultEQ® XT, Dynamic EQ® and Dynamic Volume®. These can be selected after Audyssey® Auto Setup has been performed. For additional information on Audyssey technology, please see page 109. NOTE If you have not performed Auto Setup, or if you change the speaker settings after performing Auto Setup, you may not be able to select Dynamic EQ/Dynamic Volume, and "Run Audyssey" may be displayed. In this case, either perform Audyssey Auto Setup over again or perform "Restore" (vpage 12) to return to the settings after Audyssey Auto Setup was run. Setting items MultEQ XT Select one equalizer from three modes. MultEQ XT corrects both time and frequency response problems in the listening area based on Audyssey Auto Setup calibration. We recommend "Audyssey". MultEQ XT is the prerequisite function for Dynamic EQ and Dynamic Volume. Setting details Audyssey : Optimize the frequency response of all speakers. Audyssey Byp.L/R : Optimize frequency response of speakers except front L and R speakers. Audyssey Flat : Optimize frequency response of all speakers to flat response. Manual : Apply frequency response set with "Manual EQ" (vpage 76). OFF : Turn "MultEQ XT" equalizer off. • "Audyssey", "Audyssey Byp. L/R" and "Audyssey Flat" can be selected after Audyssey Auto Setup has been performed. "Audyssey" is automatically selected after performing Audyssey Auto Setup. When "Audyssey", "Audyssey Byp. L/R" or "Audyssey Flat" is selected, illuminates. • After running Audyssey Auto Setup, if the Speaker Configuration, Distance, Channel Level, and Crossover Frequency have changed without increasing the number of speakers measured, only illuminates. • Pressing MULTEQ makes this setting. NOTE • "MultEQ XT" and "Manual" cannot be selected when "EQ Customize" is set to "Not Used" (vpage 81). • When using headphones, "MultEQ XT" is automatically set to "OFF". Setting items Dynamic EQ® Solve the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. Works with MultEQ XT. Setting details ON : Use Dynamic EQ. OFF : Do not use Dynamic EQ. • is displayed when set to "ON". • Buttons on the remote control unit or main unit can be used for operations. Press DYN EQ/VOL. Each time DYN EQ/VOL is pressed, the setting is changed as shown below. Dynamic EQ : ON Dynamic Volume : Heavy Dynamic EQ : ON Dynamic Volume : Medium Dynamic EQ : OFF Dynamic Volume : OFF Dynamic EQ : ON Dynamic Volume : OFF Dynamic EQ : ON Dynamic Volume : Light Reference Level Offset Audyssey Dynamic EQ is referenced to the standard film mix level. It makes adjustments to maintain the reference response and surround envelopment when the volume is turned down from 0 dB. However, film reference level is not always used in music or other non-film content. Dynamic EQ Reference Level Offset provides three offsets from the film level reference (5 dB, 10 dB, and 15 dB) that can be selected when the mix level of the content is not within the standard. 0dB (Film Ref) : This is the default setting and should be used when listening to movies. 5dB : Select this setting for content that has a very wide dynamic range, such as classical music. 10dB : Select this setting for jazz or other music that has a wider dynamic range. This setting should also be selected for TV content as that is usually mixed at 10 dB below film reference. 15dB : Select this setting for pop/rock music or other program material that is mixed at very high listening levels and has a compressed dynamic range. Setting is enabled when "Dynamic EQ" is "ON" (vpage 74). 74 Remote control operation buttons Move the cursor (Up/Down/Left/Right) Confirm the setting Return to previous menu