Marantz AV7005 AV7005 User Manual - English - Page 93

Other settings

Get Marantz AV7005 PDF manuals and user guides View all Marantz AV7005 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 93 highlights

Simple version Other settings SVENSKA NEDERLANDS ESPAÑOL ITALIANO Remote control settings • When you connect a remote control receiver unit (purchased separately) to the REMOTE CONTROL IN terminal of this unit, use the following procedure to disable the remote sensor function of this unit. • The remote sensor function of remote control signals is enabled by default. ON/STANDBY Switches light illumination on/off You can switch the lighting around the main display on or off. • The factory setting is "ON". FRANÇAIS DEUTSCH ENGLISH Basic version Advanced version DISPLAY STATUS ENTER Press and hold DISPLAY on the main unit for 3 seconds. • Carry out the same procedure if you want to change the settings again. nnDisabling the sensor function of the remote control unit When the main unit is in standby mode, press ON/ STANDBY while holding down STATUS and ENTER on the main unit. "Remote Lock:ON" is shown on the display, and the infrared light receiving function is disabled. nnEnabling the remote sensor function When the main unit is in standby mode, press ON/ STANDBY while holding down STATUS and ENTER on the main unit. The infrared light receiving function on the main unit is enabled. NOTE If a remote control receiver unit (purchased separately) is not connected, do not perform this setting. If you do, you will not be able to operate this unit using the remote control unit. 89 Information

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
89
Basic version
Simple version
Information
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO
ESPAÑOL
NEDERLANDS
SVENSKA
Advanced version
Other settings
Remote control settings
• When you connect a remote control receiver unit (purchased
separately) to the REMOTE CONTROL IN terminal of this unit, use
the following procedure to disable the remote sensor function of
this unit.
• The remote sensor function of remote control signals is enabled by
default.
STATUS
ENTER
ON/STANDBY
n
Disabling the sensor function of the remote
control unit
When the main unit is in standby mode, press
ON/
STANDBY
while holding down
STATUS
and
ENTER
on
the main unit.
“Remote Lock:ON” is shown on the display, and the infrared light
receiving function is disabled.
n
Enabling the remote sensor function
When the main unit is in standby mode, press
ON/
STANDBY
while holding down
STATUS
and
ENTER
on
the main unit.
The infrared light receiving function on the main unit is enabled.
NOTE
If a remote control receiver unit (purchased separately) is not
connected, do not perform this setting. If you do, you will not be able
to operate this unit using the remote control unit.
Switches light illumination on/off
You can switch the lighting around the main display on or off.
• The factory setting is “ON”.
DISPLAY
Press and hold
DISPLAY
on the main unit for 3 seconds.
• Carry out the same procedure if you want to change the settings
again.