Maytag MBF2256KEB Installation Instructions

Maytag MBF2256KEB - Bottom Freezer Refridgerator Manual

Get Maytag MBF2256KEB - Bottom Freezer Refridgerator PDF manuals and user guides View all Maytag MBF2256KEB manuals
Add to My Manuals
Save this manual to your list of manuals

Maytag MBF2256KEB manual content summary:

  • Maytag MBF2256KEB | Installation Instructions - Page 1
    the refrigerator in immediately may cause damage to internal parts. • Use an appliance dolly when moving refrigerator. ALWAYS truck refrigerator from maintain performance, the refrigerator should be leveled per instructions below. CAUTION To protect property and refrigerator from damage, observe
  • Maytag MBF2256KEB | Installation Instructions - Page 2
    Lift refrigerator door from center hinge pin. 6. For swing freezer door models only: Hold freezer door while removing hinge pin with a 5⁄16" hex head driver. Remove door from pin (on freezer door models). 9. If your model has a pullout freezer drawer, see page 5 for drawer removal instructions. 4
  • Maytag MBF2256KEB | Installation Instructions - Page 3
    personal injury or death, disconnect power to refrigerator before removing doors. After replacing doors, connect power. CAUTION To avoid possible injury, product, or property damage, you will need two people to perform the following instructions. Materials Needed: • Phillips screwdriver To Remove
  • Maytag MBF2256KEB | Installation Instructions - Page 4
    design varies from refrigerator to refrigerator. Please reference the appropriate instructions for your model below. Fresh Food Handles Standard Front Mount Handle Materials Needed: • Phillips screwdriver • 5⁄16" hex head driver To Install: 1. Remove 1⁄4" hex head screws from door face with hex
  • Maytag MBF2256KEB | Installation Instructions - Page 5
    the mounting clip is positioned to the right on both ends of the handle. 3. Rotate the handle so that the handle is flat against the door. 4. Grasp the handle firmly and slide handle to the right. To Remove: 1. With both hands, firmly grasp the handle toward the right side. 2. Slide toward
  • Maytag MBF2256KEB | Installation Instructions - Page 6
    Installation Metal Handle Materials Needed: • 3⁄32" Allen wrench • Gloves to protect hands Note: Metal handles can scratch doors. To Remove: • Loosen set screws in handle using 3⁄32" Allen wrench. • Repeat the procedure on all screws. To Replace: • Align handle with the mounting posts. •
  • Maytag MBF2256KEB | Installation Instructions - Page 7
    personal skill level. • Observe all local codes and ordinances. • Do not service ice maker unless specifically recommended in Use & Care Guide or published user-repair instructions. • Disconnect power to refrigerator before installing ice maker. • Water damage due to an improper water connection
  • Maytag MBF2256KEB | Installation Instructions - Page 8
    refrigerator to its permanent location. 7. Monitor water connection for 24 hours. Correct leaks, if necessary. Alternate connection (select models) the refrigerator to its permanent location. C 7. Monitor water connection for 24 hours. Correct leaks, if necessary. 1. Create service loop
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
3
Installation
Materials Needed:
•
3
/
8
” hex head driver
• Carpenter’s level.
1. Remove toe grille.
•
Grasp firmly and pull
outward to unclip.
2. Using hex head driver, turn
the front adjustment screws
(A)
on each side to
raise or lower the front of the refrigerator (see
illustration below).
3. Using the hex head driver, turn each of these
adjustment screws
(B)
to raise or lower the rear of
the refrigerator.
4. Using a carpenter’s level, make sure front of
refrigerator is
1
/
4
” (6 mm) or
1
/
2
bubble higher than
back of refrigerator and that the refrigerator is level
from side to side.
5. Turn stabilizing legs
(C)
clockwise
until firmly
against floor.
6. Turn adjustment screws
(A)
counterclockwise
to
allow the full weight of the refrigerator to rest on
the stabilizing legs.
7. Replace the toe grille.
Your refrigerator was packed carefully for shipment.
Remove and discard shelf packaging and tape.
Do not
remove the serial plate.
Location
•
Do not
install refrigerator near oven, radiator or other
heat source. If not possible, shield refrigerator with
cabinet material (contact a qualified contractor).
•
Do not
install where temperature falls below 55° F
(12° C) or rises above 110° F (43° C). Malfunction may
occur at this temperature.
•
Refrigerator is designed for indoor household
application only.
Measuring the Opening
When installing your refrigerator, measure carefully.
Allow
1
/
2
” space at top and
1
/
2
” space behind the machine
compartment cover (located in the rear) for proper air
circulation.
Subflooring or floor coverings (i.e. carpet, tile, wood
floors, rugs) may make your opening smaller than
anticipated.
Some clearance may be gained by using the leveling
procedure under
Leveling
.
Important:
If refrigerator is to be installed into a recess
where the top of the refrigerator is completely covered,
use distance from floor to top of hinge cap to verify
proper clearance.
Transporting Your Refrigerator
•
NEVER
transport refrigerator on its side. If an upright
position is not possible, lay refrigerator on its back.
Allow refrigerator to sit upright for approximately 30
minutes
before
plugging it in to assure oil returns to
the compressor. Plugging the refrigerator in
immediately may cause damage to internal parts.
•
Use an appliance dolly when moving refrigerator.
ALWAYS
truck refrigerator from its side or
back–
NEVER
from its front.
•
Protect outside finish of refrigerator during transport
by wrapping cabinet in blankets or inserting padding
between the refrigerator and dolly.
•
Secure refrigerator to dolly firmly with straps or
bungee cords. Thread straps through handles when
possible.
Do not
over-tighten. Over-tightening
restraints may dent or damage outside finish.
Leveling
To protect property and refrigerator from
damage, observe the following:
•
Protect vinyl or other flooring with cardboard, rugs,
or other protective material.
•
Do not
use power tools when performing leveling
procedure.
CAUTION
To enhance the appearance and maintain performance,
the refrigerator should be leveled per instructions
below.
Notes:
• Complete any required water supply connection
before
leveling.
• Some models only have adjustment screws
(A)
.
C
C
AB
A
B
•
Align the toe grille mounting clips with the lower
cabinet slots.
•
Push the toe grille firmly until it snaps into place.