Maytag MDB4949S Dimension Guide

PRODUCT DIMENSIONS

Undercounter Dishwasher

PRODUCT MODEL NUMBERS

Because Whirlpool Corporation policy includes a continuous commitment to improve

our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation

Instructions packed with product. Specifications subject to change without notice.

Page 1 of 2

If connecting dishwasher with a power supply cord:

Use power supply cord kit (Part

Number 4317824) marked for use

with dishwashers. Follow the kit

instructions for installing the power supply cord.

Power supply cord must plug into a grounded

3

prong outlet located in the cabinet next to

the

dishwasher opening. Outlet must meet all local

codes and ordinances.

Water Supply Requirements:

A hot water line with 20 to

120 psi (138 to 862 kPa) water pressure. Water

temperature

must be 120°F (49°C) water at dishwasher.

Use

3

/

8

" O.D.

copper tubing with compression fitting or

flexible braided

water supply line

.

Note:

" minimum plastic tubing is not recommended.

Use a 90°

elbow with

" hose connection with rubber

washer (

P

art

N

umber W10273460). Do not solder

within 6"

(15.2 cm) from water inlet valve.

Drain Requirements:

A new drain hose is supplied with

your dishwasher. If this is not long enough, use a new

drain

hose with a maximum length of 12' (3.7 m) (Part

N

umber

3385556) that meets all current AHAM/IAPMO

test

standards, is resistant to heat and detergent, and

fits the 1"

(2.5 cm) drain connector of the dishwasher.

Make sure to connect the drain hose to waste tee or

disposer

inlet above drain trap in house plumbing and 20"

(50.8 cm)

minimum above the floor. It is recommended

that the

drain hose either be

looped

up and securely

fastened to

the underside of

the counter

or be connected

to an air gap.

Make sure to use an air

gap

if the drain hose is

connected to house

plumbing lower than

20"

(50.8 cm) above

subfloor or

floor.

Use

1

/

2

" (1.3 cm) minimum I.D. drain line fittings.

If required, the air gap should be installed in accordance

with the air gap installation instructions. When connecting

the air gap

,

a rubber hose (not provided) will be needed

toconnect to the waste tee or disposer inlet.

air gap

C

B. For panel-ready models, dishwasher

depth is 24" (60 cm) not including the

" (1.9 cm) custom door panel.

C. Door handles may protrude forward

of the face of the dishwasher; varies

by model.

A. Insulation may be compressed

(not used on all models).

3

" -

4

"

(8.8 cm - 10.6 cm)

For 4" (10 cm)

toe

kick, height of

cabinet

opening is

34

1

/

2

" (86.3 cm).

24

"

(62.2 cm)

B

23

"

(60.6 cm)

"

(1.9 cm)

A

33

"

(85,1 cm)

min. with

wheels

removed

"

(9.4 cm)

21 "

(53.3 cm)

30"

(76.2 cm)

MDB4949SD

MDB8

95

9S

F

MDB7949SD

MDB8979

SE

Electrical Requirements:

120-volt, 60 Hz, AC-only,

15- or

20-amp. fused electrical supply. Copper wire only.

A

time

delay fuse or circuit breaker and separate circuit

is

recommended.

If direct wiring dishwasher:

Use flexible, armored

or

nonmetallic, sheathed copper

wire with grounding wire that

meets the wiring requirements for

your home and local codes and ordinances.

Use a UL Listed or CSA Approved conduit connector.

W10741197A

-D-MT

05

/

20

16

MDB89

7

9S

F

Maytag MDB4949S Dimension Guide

Maytag MDB4949S Manual

Maytag MDB4949S manual content summary: