Home » Maytag Manuals » Laundry Dryers » Maytag MED5801TW » Manual Viewer

Maytag MED5801TW Use and Care Guide

Maytag MED5801TW - 7.4 cu. Ft. Electric Dryer Manual

View all Maytag MED5801TW manuals

Add to My Manuals
Save this manual to your list of manuals

Maytag MED5801TW manual content summary:

Maytag MED5801TW | Use and Care Guide - Page 1
ELECTRIC DRYER USE & CARE GUIDE FOR QUESTIONS ABOUT FEATURES, OPERATION/PERFORMANCE, PARTS, ACCESSORIES OR SERVICE CALL: 1.800.688.9900 VISIT OUR WEBSITE AT WWW.MAYTAG.COM PARA OBTENER ACCESO AL MANUAL DE USO Y CUIDADO EN ESPAÑOL, O PARA OBTENER INFORMACIÓN ADICIONAL DE SU PRODUCTO, VISITE: WWW.
Maytag MED5801TW | Use and Care Guide - Page 2
OF CONTENTS DRYER SAFETY...3 INSTALLATION INSTRUCTIONS 4 Tools and Parts...4 Location Requirements ...4 Electrical Requirements...5 Electrical Connection ...7 Venting Requirements ...12 Plan Vent System...14 Install Vent System ...15 Install Leveling Legs ...15 Connect Vent ...16 Level Dryer ...16
Maytag MED5801TW | Use and Care Guide - Page 3
be exposed to the weather. ■ Do not tamper with controls. ■ Do not repair or replace any part of the dryer or attempt any servicing unless specifically recommended in this Use and Care Guide or in published user-repair instructions that you understand and have the skills to carry out. ■ Do not use
Maytag MED5801TW | Use and Care Guide - Page 4
outlet located within 2 ft (61 cm) of either side of the dryer. See "Electrical Requirements." ■ A sturdy floor to support the total weight (dryer and load) of 200 lbs (90.7 kg). The combined weight of a companion appliance should also be considered. ■ A level floor with a maximum slope of
Maytag MED5801TW | Use and Care Guide - Page 5
Electrical Connection To properly install your dryer, you must determine the type of electrical connection you will be using and follow the instructions provided the dryer cabinet is isolated from the neutral conductor. ■ A 4-wire power supply connection must be used when the appliance is installed
Maytag MED5801TW | Use and Care Guide - Page 6
5 ft (1.52 m) long. GROUNDING INSTRUCTIONS ■ For a grounded, cord-connected dryer: This dryer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This dryer uses a cord having an
Maytag MED5801TW | Use and Care Guide - Page 7
Direct Wire WARNING Fire Hazard Use a new UL listed 30 amp power supply cord. Use a UL listed strain relief. Disconnect power before making electrical connections. Connect neutral wire (white or center wire) to center terminal (silver). Ground wire (green or bare wire) must be connected to green
Maytag MED5801TW | Use and Care Guide - Page 8
the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Do not further tighten strain relief following instructions for your type of electrical connection: 4-wire (recommended) 3-wire (if 4-wire is not available) Electrical Connection
Maytag MED5801TW | Use and Care Guide - Page 9
screws. 5. Tighten strain relief screws. 6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with holddown screw. 7. You have completed your electrical connection. Now go to "Venting Requirements." 4-wire connection: Direct Wire IMPORTANT: A 4-wire connection is
Maytag MED5801TW | Use and Care Guide - Page 10
Neutral wire (white or center wire) E. ¾" (1.9 cm) UL listed strain relief 5. Tighten strain relief screw. 6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with holddown screw. 7. You have completed your electrical connection. Now go to "Venting Requirements." 10
Maytag MED5801TW | Use and Care Guide - Page 11
screws. 4. Tighten strain relief screws. 5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with holddown screw. 6. You have completed your electrical connection. Now go to "Venting Requirements." B D E A. External ground conductor screw B. Neutral ground wire
Maytag MED5801TW | Use and Care Guide - Page 12
of dryer rear panel. Secure cover with hold- down screw. 6. You have completed your electrical connection. not use a metal foil vent. Failure to follow these instructions can result in death or fire. F A. External ground ■ Review Vent system chart. Modify existing vent system if necessary to
Maytag MED5801TW | Use and Care Guide - Page 13
purchased from your dealer or by calling Maytag Services. For more information, see the "Assistance or Service" section. Rigid metal vent ■ For ■ Flexible metal vent must be fully extended and supported when the dryer is in its final location. ■ Remove excess flexible problems and health problems. 13
Maytag MED5801TW | Use and Care Guide - Page 14
may contact your local dealer to have the dryer converted. WARNING Fire Hazard Cover unused exhaust holes with the following kit: 279818 (white) Contact your local dealer. Failure to follow these instructions can result in death, fire, electrical shock, or serious injury. A B A. Over-the-top
Maytag MED5801TW | Use and Care Guide - Page 15
hood. 2. Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp. 3. Run vent to dryer location. Use the straightest path possible. See "Determine vent path" in "Plan Vent System." Avoid 90º turns. Use clamps to seal all joints. Do not
Maytag MED5801TW | Use and Care Guide - Page 16
(not an air cycle) for 20 minutes and start the dryer. If the dryer will not start, check the following: ■ Controls are set in a running or "On" position. ■ Start button has been pushed firmly. ■ Dryer is plugged into an outlet and/or electrical supply is on. ■ Household fuse is intact and tight, or
Maytag MED5801TW | Use and Care Guide - Page 17
result in death or fire. WARNING: To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance. This book covers several different models. Your dryer may not have all of the cycles and features described. Before using your
Maytag MED5801TW | Use and Care Guide - Page 18
ordering, please refer to the front page of the manual or contact the dealer from whom you purchased your dryer. To use the drying rack 1. Do not remove Every Load Cleaning 1. The lint screen is located in the door of the dryer. Pull the lint screen straight up. Roll lint off the screen with your
Maytag MED5801TW | Use and Care Guide - Page 19
the power supply cord. 2. Make sure leveling legs are secure in dryer base. 3. Use masking tape to secure dryer door. For direct-wired dryers: WARNING Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death
Maytag MED5801TW | Use and Care Guide - Page 20
service call... In U.S.A. www.maytag.com/help - In Canada www.maytag.ca Dryer Operation Dryer will not run ■ Has a household fuse blown, or has a circuit breaker tripped? Electric dryers metal or flexible metal vent. See the Installation Instructions. ■ Are fabric softener sheets blocking the grille
Maytag MED5801TW | Use and Care Guide - Page 21
and front of dryer require a minimum of 1" (2.5 cm) of airspace, and the rear of the dryer requires 5" (12.7 cm). See the Installation Instructions. ■ Has an , rewash and dry the clothing. ■ Is the dryer being used for the first time? The new electric heating element may have an odor. The odor will
Maytag MED5801TW | Use and Care Guide - Page 22
sales. ■ Specialized customer assistance (Spanish speaking, hearing impaired, limited vision, etc.). ■ Referrals to local dealers, repair parts distributors and service companies. Maytag® appliances designated service technicians are trained to fulfill the product warranty and provide after-warranty
Maytag MED5801TW | Use and Care Guide - Page 23
Notes 23
Maytag MED5801TW | Use and Care Guide - Page 24
, when this major appliance is operated and maintained according to instructions attached to or furnished with the product, Maytag Corporation or Maytag Limited (hereafter "Maytag") will pay for Factory Specified Parts and repair labor to correct defects in materials or workmanship. Service must be