Home » Maytag Manuals » Laundry Dryers » Maytag MEDC300XW » Manual Viewer

Maytag MEDC300XW Installation Instructions

Maytag MEDC300XW Manual

UPC - 883049199061

View all Maytag MEDC300XW manuals

Add to My Manuals
Save this manual to your list of manuals

Maytag MEDC300XW manual content summary:

Maytag MEDC300XW | Installation Instructions - Page 1
Electric Dryer Installation Instructions 29" Wide Models - U.S.A. Only Para obtener acceso al manual de uso y cuidado en español, Contents DRYER SAFETY 2 Installation Requirements 2 Tools and Parts 2 Location Requirements 3 Electrical Requirements 4 Install Leveling Legs 5 Electrical Connection
Maytag MEDC300XW | Installation Instructions - Page 2
. INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools needed: Flat-blade screwdriver 2 #2 Phillips screwdriver Wire stripper (direct wire installations) Tin snips
Maytag MEDC300XW | Installation Instructions - Page 3
30 amp circuit. ■■ If you are using power supply cord, a grounded electrical outlet located within 2 ft. (610 mm) of either side of dryer. See "Electrical Requirements." ■■ A sturdy floor to support the total weight (dryer and load) of 200 lbs. (90.7 kg). The combined weight of a companion appliance
Maytag MEDC300XW | Installation Instructions - Page 4
is manufactured ready to install with a 3-wire electrical supply connection. The neutral ground wire is permanently connected to the neutral conductor (white wire) within the dryer. If the dryer is installed with a 4-wire electrical supply connection, the neutral ground wire must be removed from the
Maytag MEDC300XW | Installation Instructions - Page 5
at least 4 ft. (1.22 m) long. The wires that connect to the dryer must end wire (ground 4-wire receptacle conductor) may be either green or bare. The (14-30R) neutral conductor must be identified by a white cover. If your outlet looks like this: 3-wire receptacle (10-30R) Then choose a 3-wire
Maytag MEDC300XW | Installation Instructions - Page 6
ul listed 30 amp power supply cord. use a ul listed strain relief. Disconnect power before making electrical connections. Connect neutral wire (white or center wire) to center terminal (silver). Ground wire (green or bare wire) must be connected to green ground connector. Connect remaining 2 supply
Maytag MEDC300XW | Installation Instructions - Page 7
clamp sections (C) together. CD E G A. 4-wire receptacle (NEMA type 14-30R) B. 4-prong plug C. Ground prong D. Neutral prong E. Spade wire (E) from external ground conductor screw (A). 4. Connect neutral ground wire and neutral wire C B E Connect neutral ground wire (E) and neutral wire (white
Maytag MEDC300XW | Installation Instructions - Page 8
to neutral wire. B D E A C GF A. 3-wire receptacle (NEMA type 10-30R) B. 3-wire plug C. Neutral prong D. Spade terminals with upturned ends E. 3/4" (19 mm) UL listed strain relief F. Ring terminals G. Neutral (white or center wire) 3. Remove center screw B Connect remaining wires to outer
Maytag MEDC300XW | Installation Instructions - Page 9
terminal block opening, screw the removable conduit connector onto the strain relief threads (C). 2. Attach direct wire cable to strain relief (127 5" mm) Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer may be moved if needed. Strip 5" (127 mm) of outer covering from end of
Maytag MEDC300XW | Installation Instructions - Page 10
hook facing right) of neutral wire (white or center wire) (C) of direct wire cable under center screw of terminal block (B). Squeeze hooked ends together and tighten screw. 7. Connect ground wire A (893m½m" ) Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer may be moved if needed
Maytag MEDC300XW | Installation Instructions - Page 11
together. Tighten screw. 7. Connect remaining wires E Connect neutral ground wire (E) and neutral wire (white or center wire) (C) of power supply cord or cover into slot of dryer rear panel. Secure cover with hold-down screw. Now, go to Venting Requirements. Optional 3-wire Connection You must
Maytag MEDC300XW | Installation Instructions - Page 12
of the system and make sure exhaust hood is not plugged with lint. Replace plastic or metal foil vents with rigid metal or flexible metal vents. Review Vent system chart and if necessary, modify existing vent system to achieve best drying performance. Good Better Clamps: ■■ Use clamps to seal
Maytag MEDC300XW | Installation Instructions - Page 13
Select the type best for your installation. Two close-clearance installations are shown. Refer to the manufacturer's instructions. A A. Dryer B. Elbow C. 1-800-807-6777 or visit us at www.whirlpoolparts.ca. Part Number Descriptions 8171587RP 0-5" Metal vent periscope 4396037RP 0"-18" Metal vent
Maytag MEDC300XW | Installation Instructions - Page 14
mobile home. Terminate the exhaust vent outside. Vent System Chart (Long Vent Models Only) Number of 90° turns or elbows Type of vent Box/louvered, or Angled hoods 0 Rigid metal 120 ft. (36.6 m) 1 Rigid metal 110 ft. (33.5 m) 2 Rigid metal 100 ft. (30.5 m) 3 Rigid metal 90 ft. (27
Maytag MEDC300XW | Installation Instructions - Page 15
Care Guide. q Set the dryer on a full heat cycle (not an air cycle) for 20 minutes and start the dryer. If the dryer will not start, check the following: ■■ Controls are set in a running or "On" position. ■■ Start button has been pushed firmly. ■■ Dryer is plugged into an outlet and/or electrical
Maytag MEDC300XW | Installation Instructions - Page 16
and tight, or that both circuit breakers have not tripped. If there is still no heat, contact a qualified technician. NOTE: You may notice an odor when the dryer is first heated. This odor is common when the heating element is first used. The odor will go away. Reverse Door Swing (Optional) If your
Maytag MEDC300XW | Installation Instructions - Page 17
with door catch. If needed, slide door catch left or right within slot to adjust alignment. Super Wide Side-Swing Door 1. Place towel on dryer Lift door until top screws in dryer cabinet are in large part of hinge slot. Pull door forward off screws. Set door (handle side up) on top of
Maytag MEDC300XW | Installation Instructions - Page 18
separate from hinge screws as they are diferent sizes. Holding door over towel on dryer, grasp sides of outer door and lift to separate it from inner door. removed. Insert 4 door screws. 7. Flip door over Reattach door hinges to dryer door so that the larger hole is at the bottom of the hinge. 9.
Maytag MEDC300XW | Installation Instructions - Page 19
plugs on left side of dryer cabinet. Transfer plugs into hinge holes on opposite side of dryer cabinet. 11. Insert screws in hinge holes on dryer cabinet Remove door strike plug slot to adjust alignment. Troubleshooting See the Use and Care Guide or visit our website and reference Frequently Asked Questions
Maytag MEDC300XW | Installation Instructions - Page 20
W10096987A W10097001A-SP 2©Al0l2r0ig1h0tsWrehsirelprvoeodl Corporation. ® Registered Trademark/TM Trademark of Whirlpool, U.S.A. 2/10 Printed in U.S.A.