Maytag MEDE200XW Installation Instructions
Maytag MEDE200XW Manual
 |
UPC - 883049193083
View all Maytag MEDE200XW manuals
Add to My Manuals
Save this manual to your list of manuals |
Maytag MEDE200XW manual content summary:
- Maytag MEDE200XW | Installation Instructions - Page 1
Inlet Hose 17 Connect Vent 18 Level Dryer 18 Complete Installation Checklist 19 Door reversal 19 StaCKING WASHER AND DRYER 19 TROUBLESHOOTING 19 INSTALLATION NOTES Date of purchase Date of installation Installer Model number Serial number Para obtener acceso al manual de uso y cuidado - Maytag MEDE200XW | Installation Instructions - Page 2
DRYER SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and if you don't immediately follow instructions. WARNING You can be killed or seriously injured if you don't follow instructions. All safety messages will tell - Maytag MEDE200XW | Installation Instructions - Page 3
installing dryer on pedestal, do not use leveling legs. Optional Equipment: (Not supplied with dryer) Refer to your "Use and Care Guide" for information about accessories available for your dryer. Parts needed: (Not supplied with dryer) Check local codes. Check existing electrical supply and venting - Maytag MEDE200XW | Installation Instructions - Page 4
(if needed) which are provided. ■■ 20-100 psi (138-690 kPa) for best performance. ■■ Level floor with maximum slope of 1" (25 mm) under entire dryer. If slope is greater than 1" (25 mm), install Extended Dryer Feet Kit, Part Number 279810. If not level, clothes may not tumble properly and automatic - Maytag MEDE200XW | Installation Instructions - Page 5
times. Spacing for recessed area or closet installation All dimensions show recommended spacing allowed, with tested spacing of 0" (0 mm) clearance on sides and rear. ■■ Additional spacing should be considered for ease of installation and servicing. ■■ Additional clearances might be required for - Maytag MEDE200XW | Installation Instructions - Page 6
) NOTE: Some models not recommended for undercounter installation. Mobile home - Additional installation requirements: This dryer is suitable for mobile home installations. The installation must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the - Maytag MEDE200XW | Installation Instructions - Page 7
electrician or service representative or personnel if you are in doubt as to whether the dryer is properly grounded. Do not modify the plug provided with the dryer: if it will not fit the outlet, have a proper outlet installed by a qualified electrician. SAVE THESE INSTRUCTIONS To avoid damaging - Maytag MEDE200XW | Installation Instructions - Page 8
Connection Power Supply Cord 2. Remove terminal block cover Electrical Connection Options 1. Choose electrical connection type Power supply cord 4-wire receptacle (NEMA Type 14-30R): Go to Power Supply Cord Connection. Power supply cord 3-wire receptacle (NEMA Type 10- - Maytag MEDE200XW | Installation Instructions - Page 9
the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Do not further tighten strain relief Supply Cord Connection IMPORTANT: A 4-wire connection is required for moble homes and where local codes do not permit the use of 3-wire connections - Maytag MEDE200XW | Installation Instructions - Page 10
to outer terminal block screws. Tighten screws. Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. Now, go to "Venting Requirements". 3-wire Power Supply Cord Connection Use where local codes permit connecting cabinet-ground conductor to - Maytag MEDE200XW | Installation Instructions - Page 11
Wire Connection IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit 3-wire connections. 1. (127 5" mm) Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer may be moved if needed. Strip 5" (127 mm) of outer covering from end of cable - Maytag MEDE200XW | Installation Instructions - Page 12
under outer terminal block screws (hooks facing right). Squeeze hooked ends together and tighten screws. Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. Now, go to "Venting Requirements". Remove center terminal block screw (B). 12 - Maytag MEDE200XW | Installation Instructions - Page 13
). Squeeze hooked ends together and tighten screws. Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. Now, go to "Venting Requirements". Place hooked ends of remaining wires under outer terminal block screws (hooks facing right). Tighten - Maytag MEDE200XW | Installation Instructions - Page 14
crushing and kinking. Flexible metal vent: (Acceptable only if accessible to clean) ■■ Must be fully extended and supported in final dryer location. ■■ Remove excess to avoid sagging and kinking that may result in reduced airflow and poor performance. ■■ Do not install in enclosed walls, ceilings - Maytag MEDE200XW | Installation Instructions - Page 15
close-clearance installations are shown. Refer to the manufacturer's instructions. If you prefer, dryer may be converted to exhaust out right side, left side, or through bottom. You must contact your local dealer to have dryer converted. Special provisions for mobile homes: Exhaust vent must be - Maytag MEDE200XW | Installation Instructions - Page 16
35 ft. (10.7 m) 29 ft. (8.8 m) 4 Rigid metal 27 ft. (8.2 m) 21 ft. (6.4 m) NOTE: Bottom exhaust installations have a 90º turn inside the dryer. To determine maximum exhaust length, add one 90º turn to the chart. Install Vent System 1. Install exhaust hood 12" min. (305 mm) 12" min. (305 mm - Maytag MEDE200XW | Installation Instructions - Page 17
-steam models, skip to "Connect Vent" on page 18. The dryer must to the "Y" connector. Attach washer cold inlet hose to other side of "Y" connector. Screw on coupling by hand until it is Attach other end of long hose to fill valve at bottom of dryer back panel. Screw on coupling by hand until it is - Maytag MEDE200XW | Installation Instructions - Page 18
crushing or kinking vent. After dryer is in place, remove cardboard from under dryer. Level dryer 1. Level Dryer Check for leaks around "Y" connector, faucets, and hoses. Connect Vent 1. Connect vent to exhaust outlet Place level here Check levelness of dryer from side to side. Repeat from front - Maytag MEDE200XW | Installation Instructions - Page 19
" section in your "Use and Care Guide". STACkING WASHER AND DRYER If you prefer to stack your washer and dryer: A stack kit, Part Number 8572546 is available to order. For further information, see "Assistance or Service" section in your "Use and Care Guide". Troubleshooting See your "Use and Care - Maytag MEDE200XW | Installation Instructions - Page 20
W10240579C W10240583C-SP © 2010 All rights reserved 20 08/10 Printed in U.S.A.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
 |
 |
W10240579C
W10240583C-SP
Table of Contents
DRYER SAFETY
.........................................................................
2
INSTALLATION REQUIREMENTS
.............................................
3
Tools and Parts
......................................................................
3
Location Requirements
.........................................................
4
Electrical Requirements
........................................................
6
Install Leveling Legs
..............................................................
7
Electrical Connection
............................................................
8
Venting Requirements
.........................................................
14
Plan Vent System
.................................................................
15
Install Vent System
..............................................................
16
Connect Inlet Hose
..............................................................
17
Connect Vent
........................................................................
18
Level Dryer
...........................................................................
18
COMPLETE INSTALLATION CHECKLIST
..............................
19
DOOR REVERSAL
....................................................................
19
STACKING WASHER AND DRYER
.........................................
19
TROUBLESHOOTING
..............................................................
19
INSTALLATION NOTES
Date of purchase:
_________________________________
Date of installation:
_______________________________
Installer:
________________________________________
Model number:
___________________________________
Serial number:
___________________________________
Electric Dryer Installation Instructions
Para obtener acceso al manual de uso y cuidado en español, o para obtener información adicional acerca de su
producto, visite:
www.whirlpool.com
Tenga listo su número de modelo completo. Puede encontrar el número de modelo y de serie dentro de la cavidad
superior de la puerta.