Home » Maytag Manuals » Ranges » Maytag MER7765WS » Manual Viewer

Maytag MER7765WS Installation Instructions

Maytag MER7765WS - Ceramic Range - Stainless Manual

UPC - 883049176277

View all Maytag MER7765WS manuals

Add to My Manuals
Save this manual to your list of manuals

Maytag MER7765WS manual content summary:

Maytag MER7765WS | Installation Instructions - Page 1
INSTALLATION INSTRUCTIONS 30" (76 CM) FREESTANDING ELECTRIC RANGES Table of Contents RANGE SAFETY 2 INSTALLATION REQUIREMENTS 3 Tools and Parts 3 Location Requirements 3 Electrical Requirements - U.S.A. Only 4 INSTALLATION INSTRUCTIONS 6 Unpack Range 6 Install Anti-Tip Bracket 6 Electrical
Maytag MER7765WS | Installation Instructions - Page 2
RANGE SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and the range and be killed. Connect anti-tip bracket to rear range foot. Reconnect the anti-tip bracket, if the range is moved. Failure to follow these instructions
Maytag MER7765WS | Installation Instructions - Page 3
It is the installer's responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located on the left side frame behind the storage drawer panel. ■ The range should be located for convenient use in the kitchen. ■ To eliminate the
Maytag MER7765WS | Installation Instructions - Page 4
(75.9 cm) width E. 25" (63.5 cm) depth F. Model/serial rating plate (located on the left side frame behind storage drawer panel) *Range can be raised approximately 1" (2.5 cm) by adjusting the leveling legs. Cabinet Dimensions Cabinet opening dimensions shown are for 25" (64.0 cm) countertop depth
Maytag MER7765WS | Installation Instructions - Page 5
be using and follow the instructions provided for it here. ■ Range must be connected to the proper electrical voltage and frequency as specified on the model/serial number rating plate. The model/serial number rating plate is located behind the control panel or on the oven frame behind the storage
Maytag MER7765WS | Installation Instructions - Page 6
INSTALLATION INSTRUCTIONS Unpack Range WARNING Excessive Weight Hazard Use two or more people to move and install range. Failure to do so can result in back or other injury. 1. Remove shipping materials, tape and film from range. 2. Remove oven racks and parts package from inside oven. 3. Do not
Maytag MER7765WS | Installation Instructions - Page 7
grounded outlet. Failure to follow these instructions can result in death, fire, or electrical shock. Electrical Shock Hazard Disconnect power before servicing. Use 8 gauge copper or 6 gauge aluminum wire. Electrically ground range. Failure to follow these instructions can result in death, fire, or
Maytag MER7765WS | Installation Instructions - Page 8
(NEMA type 14-50R) A UL listed, 250-volt minimum, 40-amp, range power supply cord 4-wire connection: Power supply cord A A. UL listed strain 1. Part of metal ground strap must be cut out and removed. A B C 5. Complete installation following instructions for your type of electrical connection
Maytag MER7765WS | Installation Instructions - Page 9
, use only a power cord rated at 250 volts minimum, 40 amps or 50 amps that is marked for use with nominal 1³⁄₈" (3.5 cm) diameter connection opening, with ring terminals and marked for use with ranges. 8. Tighten strain relief screws. 9. Replace terminal block access cover. D B C A. 10-32
Maytag MER7765WS | Installation Instructions - Page 10
Direct Wire Installation: Copper or Aluminum Wire This range may be connected directly to the fuse disconnect or circuit breaker box. Depending on your electrical supply, make the required 3-wire or 4-wire connection. 1. Strip outer covering back 3" (7.6 cm) to expose wires. Strip the insulation
Maytag MER7765WS | Installation Instructions - Page 11
posts with 10-32 hex nuts. 8. Securely tighten hex nuts. 9. Replace terminal block access cover. 3-wire connection: Direct Wire Use this method only Pull the wires through the conduit on cord/conduit plate on bottom of range. Allow enough slack to easily attach the wiring to the terminal block. A
Maytag MER7765WS | Installation Instructions - Page 12
back into position. Check that rear leveling leg is engaged in anti-tip bracket. NOTE: Range must be level for satisfactory baking performance. 4. Replace the storage drawer (on some models). A. Drawer clip 3. Depress the drawer clip by pressing the screwdriver handle toward the side of the storage
Maytag MER7765WS | Installation Instructions - Page 13
and oven. See the Use and Care Guide for specific instruction on range operation. If range does not operate, check the following: ■ Household fuse is intact and tight; or circuit breaker has not tripped. ■ Range is plugged into an outlet. ■ Electrical supply is connected. ■ See "Troubleshooting" in
Maytag MER7765WS | Installation Instructions - Page 14
-tip bracket is installed: ■ Look for the anti-tip bracket securely attached to floor. ■ Slide range back so rear range foot is under anti-tip bracket. Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or
Maytag MER7765WS | Installation Instructions - Page 15
Left edge ANTI-TIP BRACKET TEMPLATE Cut on dotted lines and place the left edge against the left side cabinet and the top edge against the rear wall. Top edge 15
Maytag MER7765WS | Installation Instructions - Page 16
W10252706B © 2009. All rights reserved. 9/09 Printed in U.S.A.