Maytag MMV4203WW Installation Instructions
Maytag MMV4203WW Manual
 |
View all Maytag MMV4203WW manuals
Add to My Manuals
Save this manual to your list of manuals |
Maytag MMV4203WW manual content summary:
- Maytag MMV4203WW | Installation Instructions - Page 1
further notes. These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration in these installation instructions. Table of Contents MICROWAVE HOOD COMBINATION SAFETY 1 INSTALLATION REQUIREMENTS 2 Tools and Parts 2 Remove - Maytag MMV4203WW | Installation Instructions - Page 2
(attached to back of microwave oven) Cardboard template (part of packaging) Aluminum grease filters Charcoal filters (Depending on model, charcoal filters may not be included. See User Instructions.) NOTE: Depending on model, aluminum grease filter and charcoal filter may be combined. Materials - Maytag MMV4203WW | Installation Instructions - Page 3
if the grounding instructions are not completely understood, or if doubt exists as to whether the microwave oven is properly grounded. Do not use an extension cord. If the power supply cord is too short, have a qualified electrician or serviceman install an outlet near the microwave oven. SAVE THESE - Maytag MMV4203WW | Installation Instructions - Page 4
INSTALLATION INSTRUCTIONS Remove Mounting Plate Depending on your model, the mounting plate may be in the foam packaging, or it may be attached to the back of the microwave oven. NOTE: To avoid possible damage to the work surface, cover the work surface. 1. Remove any remaining contents from the - Maytag MMV4203WW | Installation Instructions - Page 5
ports face the top of microwave oven, and flat sides of blower motor face back of microwave oven. Lower blower motor back into microwave oven. A 6. Reattach blower motor to back of microwave oven with 2 screws removed in Step 3 of "Wall Venting Installation Only." Securely tighten screws. NOTE - Maytag MMV4203WW | Installation Instructions - Page 6
wall studs exist within the cabinet opening, do not install the microwave oven. 1. Using a stud finder, locate the edges of A. End holes (on mounting plate) B. Cabinet opening vertical centerline C. Wall stud centerlines D. Holes for lag screws E. Support tabs F. Mounting plate center markers 6 - Maytag MMV4203WW | Installation Instructions - Page 7
Mark Rear Wall The microwave oven must be installed on a minimum of 1 wall stud, preferably 2, using a minimum of . They must each be 14¹⁄₈" (35.9 cm) from the centerline. 5. With the support tabs facing forward (see illustrations in "Locate Wall Stud(s)" section), align the mounting plate center - Maytag MMV4203WW | Installation Instructions - Page 8
1 wall stud as well as at both ends. 1. With the support tabs of the mounting plate facing forward, insert 1/4-20 x 3" guides. ■ If the wall behind the microwave oven (as installed) has a partial wall covering (for example, tile backsplash), be sure the "Rear Wall" arrows align to the thickest part - Maytag MMV4203WW | Installation Instructions - Page 9
the damper blade hinge is at the top, and the damper blade opens away from the microwave oven. A B C D Install the Microwave Oven WARNING Excessive Weight Hazard Use two or more people to move and install microwave oven. Failure to do so can result in back or other injury. IMPORTANT: The control - Maytag MMV4203WW | Installation Instructions - Page 10
cabinet bottom and the microwave oven. A 2. Connect vent to damper assembly. A B A. Vent B. Damper assembly (under vent) Complete Installation 1. Install filters. Refer to the User Instructions for filter placement. WARNING A. Bolts For Roof Venting Installation Only 1. Insert damper assembly - Maytag MMV4203WW | Installation Instructions - Page 11
only. NOTES: ■ Vent materials needed for installation are not provided with microwave hood combination. ■ We do not recommend using at least 3" (7.6 cm) of clearance between the top of the microwave oven and the transition piece. See "Rectangular to Round Transition" illustration. Rectangular - Maytag MMV4203WW | Installation Instructions - Page 12
) wide. Replacement Parts If any of the installation hardware needs to be replaced, call us at our toll free number listed in the User Instructions. Following is a list of available replacement parts. You will need your model number located on the front facing of the microwave oven opening, behind
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
 |
 |
MICROWAVE HOOD COMBINATION
INSTALLATION INSTRUCTIONS
MICROWAVE HOOD COMBINATION SAFETY
This product is suitable for use above electric or gas cooking products up to and including 36" (91.4 cm) wide. See “Installation
Requirements” section for further notes.
These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration in
these installation instructions.
Table of Contents
MICROWAVE HOOD COMBINATION SAFETY
..............................
1
INSTALLATION REQUIREMENTS
...................................................
2
Tools and Parts
...............................................................................
2
Remove Cardboard Template
........................................................
2
Location Requirements
...................................................................
2
Product Dimensions
.......................................................................
3
Electrical Requirements
..................................................................
3
INSTALLATION INSTRUCTIONS
.....................................................
4
Remove Mounting Plate
.................................................................
4
Rotate Blower Motor
.......................................................................
4
Locate Wall Stud(s)
.........................................................................
6
Mark Rear Wall
................................................................................
7
Drill Holes in Rear Wall
....................................................................
7
Attach Mounting Plate to Wall
........................................................
8
Prepare Upper Cabinet
...................................................................
8
Install Damper Assembly
................................................................
9
Install the Microwave Oven
............................................................
9
Complete Installation
....................................................................
10
VENTING DESIGN SPECIFICATIONS
............................................
11
ASSISTANCE
...................................................................................
12
Replacement Parts
.......................................................................
12
Accessories
...................................................................................
12
W10344702B
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING