Miele T 8023 C Operating and Installation manual
Miele T 8023 C Manual
 |
View all Miele T 8023 C manuals
Add to My Manuals
Save this manual to your list of manuals |
Miele T 8023 C manual content summary:
- Miele T 8023 C | Operating and Installation manual - Page 1
Operating and Installation Instructions Condenser Dryer T 8023 C To prevent accidents and appliance damage read these instructions before installation or use. en - US, CA M.-Nr. 09 460 400 - Miele T 8023 C | Operating and Installation manual - Page 2
16 Cleaning the condenser 17 Quick Guide 19 Dryer Care 19 Changing the light bulb 19 Frequently asked questions 20 After sales service 22 Installation instructions 23 IMPORTANT SAFETY INSTRUCTIONS 24 Washer / Dryer Stack 25 Electrical connection 26 Installation 27 Installation site 28 - Miele T 8023 C | Operating and Installation manual - Page 3
the dryer if the drum is moving. ~ Do not install or store this appliance where it will be exposed to the weather. ~ Do not tamper with the controls. ~ Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in these operating instructions. Repairs - Miele T 8023 C | Operating and Installation manual - Page 4
cleaned periodically by qualified personnel. This dryer is intended for residential use only! ~ GROUNDING INSTRUCTIONS This appliance must be grounded. In the plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. - Miele T 8023 C | Operating and Installation manual - Page 5
a program when pressed. Flashes during program selection and lights once the program starts. h "Door" button Opens the door when the program has finished. If the dryer is on, the drum interior will light when the door is opened. If the door is left open, the light will go off after a few - Miele T 8023 C | Operating and Installation manual - Page 6
refer to the "Installation Instructions". ^ Before using for the first time, clean the drum with a cloth. Before drying, check fabric care labels for special drying instructions. q Dry with normal temperature r Dry with low temperature (select "Gentle" option) s Do not dry in a tumble dryer Program - Miele T 8023 C | Operating and Installation manual - Page 7
shut. 2. Select a program For best results use liquid fabric softener when washing laundry. Fabric softener sheet may clog the filters and cause the dryer to overheat. ^ Press the e or - button until the desired program indicator lights. To prevent fabric damage, check that laundry will not be - Miele T 8023 C | Operating and Installation manual - Page 8
Using the dryer Program Fabric Note Normal Available drying options: Turbo, Gentle, Anti-crease Extra Dry Multi-layer fabrics, mixed loads of sturdy cottons, e.g. jeans, towels. The "Extra - Miele T 8023 C | Operating and Installation manual - Page 9
3. Select a drying option (if needed) ^ A drying option can be selected or deselected with each press of the button. Using the dryer OPTIONS Turbo Fast drying for sturdy fabrics with increased temperature and a reduced program length. Gentle For drying delicate fabrics slowly at a lower temperature - Miele T 8023 C | Operating and Installation manual - Page 10
indicator illuminates. In the "Wrinkle-free" program, only "More Dry", "Normal" and "Less Dry" can be selected. To adjust the buzzer volume: - turn the dryer on - close the door - select a program - if the indicator is lit, press the "Buzzer" button so the indicator light goes out. ^ Press and hold - Miele T 8023 C | Operating and Installation manual - Page 11
the "Door" button. ^ Open the door. ^ Remove the laundry. ^ Check that the drum is empty. ^ Clean the lint filter after each use (see "Dryer care"). ^ Close the door. ^ Press the "On/Off" button to turn off the dryer. ^ Empty the condensed water container weekly (if not connected to a drain). 11 - Miele T 8023 C | Operating and Installation manual - Page 12
" and "Wrinkle-free" programs). ^ Press and release the "Start/Stop" button to start the new program. Adding or removing laundry during a program ^ Turn off the dryer using the "On/Off" button. ^ Press the "Door" button. ^ Open the door. ,CAUTION - Do not touch the rear of the drum while adding or - Miele T 8023 C | Operating and Installation manual - Page 13
and the door is closed. 2. Press and hold the "Anti-crease" and "DRYNESS" buttons at the same time, hold until step 5. 3. Turn on the dryer with the "On/Off" button. 4. Press the "OPTIONS" button 3 times. 5. Release the "Anti-crease" and "DRYNESS" buttons. The "Child lock" indicator will flash and - Miele T 8023 C | Operating and Installation manual - Page 14
Dryer care Cleaning the lint filter The lint filter must be cleaned after every program. ^ Open the door and remove the lint filter, 1, by gently lifting - Miele T 8023 C | Operating and Installation manual - Page 15
the power main, tripping the circuit breaker or unplugging the power cord before performing maintenance. Never use abrasive cleaners, scouring pads, steel wool or caustic (oven) cleaners on the dryer. They will damage the surface. ^ Take the door lint filters out by turning the knob at the filter - Miele T 8023 C | Operating and Installation manual - Page 16
Dryer care Emptying the condensed water container Depending on the installation, the condensed water will either be pumped to a drain or collected in the condensed water container, located in the upper left corner of the machine. The container holds approximately 1 gallon of water. The container - Miele T 8023 C | Operating and Installation manual - Page 17
. Clean approximately every 100 uses when the dryer is used often. ^ Turn the condenser door lock down and remove the door up and out. Removing the condenser The access panel to the condenser is located on the lower left corner of the dryer. ^ Turn the condenser lock up. ^ Open the access panel - Miele T 8023 C | Operating and Installation manual - Page 18
Dryer care Rinsing the condenser Returning the Condenser ^ Put the condenser back in place in the reverse order. Check that the gasket around the front of the condenser is flush and not crimped. ^ To prevent leaks, make certain the condenser is pushed in all the way and locked in place. ^ Restore - Miele T 8023 C | Operating and Installation manual - Page 19
Quick Guide Remove this guide for easy reference Please read all instructions, especially the "Important Safety Instructions", before using the dryer. - Miele T 8023 C | Operating and Installation manual - Page 20
Quick Guide 1.Turn on the dryer and load the laundry 2. Select a program ^ Press the "On/Off" button to turn on the dryer. ^ Press the "Door" button to open the door. ^ Load the laundry into the drum. Make sure that there is enough space in the drum for clothes to tumble freely. ^ Press the e or - Miele T 8023 C | Operating and Installation manual - Page 21
4. Select the dryness level Quick Guide 5. Select the buzzer (if desired) 6. Start the program ^ Press the selection button until the desired indicator illuminates. ^ Press the " . ^ Press "Door" and remove the laundry. ^ Clean the lint filter. ^ Press the "On/Off" button to turn off the dryer. - Miele T 8023 C | Operating and Installation manual - Page 22
Quick Guide Program When to use Note Normal Extra Dry More Dry Normal Less Dry Available drying options Turbo, Gentle, Anti-crease For laundry to be folded - Miele T 8023 C | Operating and Installation manual - Page 23
,To reduce the risk of electric shock, disconnect the dryer from the power supply by shutting off the power main, of the drum opening. ^ Replace the light bulb with a temperature proof bulb, available from Miele. The light bulb must not exceed the maximum wattage listed on the data plate. ^ Flip - Miele T 8023 C | Operating and Installation manual - Page 24
if the program stops, the "End/Anti-crease" indicator lights and the buzzer sounds? Possible fault Solution The drum is empty. Load laundry into the dryer. The dryer will not operate when the drum is empty. Single items should be dried with "Sturdy" or a timed program and dry items in the "Fluff - Miele T 8023 C | Operating and Installation manual - Page 25
. Reduce the load size. Metal zippers interfere with the dryer's Select a timed program to avoid over moisture sensors. drying. The condenser is clogged with lint or Clean the condenser periodically (see detergent residue. "Dryer care"). The air vent below the door is blocked. Remove - Miele T 8023 C | Operating and Installation manual - Page 26
Authorized Service Provider using genuine Miele parts. Only genuine Miele parts installed by factory trained professionals can guarantee the safety, reliability and longevity of your Miele appliance. PC Update The indicator on the control panel marked # allows a technician to update the dryer with - Miele T 8023 C | Operating and Installation manual - Page 27
Installation Instructions To prevent accidents and machine damage read these instructions before installation or use. - Miele T 8023 C | Operating and Installation manual - Page 28
clothes dryer according to the manufacturer's instructions and local codes. ~ Repair and maintenance work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and could void the warranty. ~ Before installation, disconnect the tumble dryer from - Miele T 8023 C | Operating and Installation manual - Page 29
The tumble dryer can also be placed on top of a Miele washing machine for a stacked installation. An appropriate stacking kit is required. The stacking kit is available from your Miele dealer or the Miele Technical Service Department. ,Installation of the stacking kit must be performed by a Miele - Miele T 8023 C | Operating and Installation manual - Page 30
GROUNDING INSTRUCTIONS into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. The dryer comes with a 5 ft long, 12 of electric shock. Check with a qualified electrician or service representative or personnel if you are in doubt as to - Miele T 8023 C | Operating and Installation manual - Page 31
Front view Installation a Power cord with plug b Condensed water container c Control panel d Door e Access panel to condenser f Four height adjustable feet g Optional drain hose: An alternative to using the condensed water container is to drain condensed water into a sink, standpipe or gully. 27 - Miele T 8023 C | Operating and Installation manual - Page 32
built-in application. a Handle for transportation (arrows) b Air intake opening to cool the condenser c Power cord with plug d Condensate drain hose e Accessories for connection to a sink standpipe Transporting the dryer to the installation site The rear excess end of the lid has a handle box for - Miele T 8023 C | Operating and Installation manual - Page 33
necessary. It must be installed by a Miele Service Technician. The cover plate of the built-under kit replaces the appliance lid and ensures electrical safety. An installation manual is supplied with the built-under spacer kit. The electrical connection should be near the dryer and accessible at all - Miele T 8023 C | Operating and Installation manual - Page 34
. Otherwise drying times and energy usage may increase. Do not install the dryer next to a refrigerator. The warm air which emanates from the dryer can affect the thermostat of the refrigerator, causing it to run continuously. ^ The dryer must be level to ensure safe and proper operation. Room - Miele T 8023 C | Operating and Installation manual - Page 35
the dryer. The condensed water can also be drained directly if the machine is installed near a sink or a standpipe so that the condensed small amount of remaining water. Keep a container at hand. ^ Guide the hose depending on the installation to the left or right. ^ Leave the hose in the middle - Miele T 8023 C | Operating and Installation manual - Page 36
Installation Draining the condensed water into a sink ^ Secure the hose carefully, e.g. by tying the hose to the water tap, to avoid damage by overflowing water. ^ Use the curved guide to prevent the drain hose from becoming kinked (see Front view illustration). Connection to a standpipe ^ Insert - Miele T 8023 C | Operating and Installation manual - Page 37
Installation Installation requirements demanding a non-return valve ,To prevent water from flowing back into the machine a non-return valve must be installed at the following installations sink standpipe. - Installation to a sink standpipe - Several installation possibilities where additionally - Miele T 8023 C | Operating and Installation manual - Page 38
tighten the hose clamp 3 directly behind the sink connecting nut. ,Install the non-return valve 5 vertical or slightly angled. If installed horizontal it will not operate correctly. ^ Connect the non-return valve 5 to the dryer drain hose 6. See illustration for the correct direction. ^ Fasten the - Miele T 8023 C | Operating and Installation manual - Page 39
Old appliances may contain materials that can be recycled. Please contact your local recycling authority about the possibility of recycling these materials. Ensure that a discarded dryer presents no danger to children. When being stored for disposal remove the door to the drying compartment. 35 - Miele T 8023 C | Operating and Installation manual - Page 40
All rights reserved / 2812 M.-Nr. 09 460 400 / 00 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
 |
 |
Operating and Installation Instructions
Condenser Dryer
T 8023 C
To prevent accidents
and appliance damage
read these instructions
before
installation or use.
en - US, CA
M.-Nr. 09 460 400