Milwaukee Tool 2118-21 Operators Manual

Fig. 3

Fig. 1

SPECIFICATIONS

Cat. No.

............................................................

2118-20

USB-C Input Volts

...................................................

5 DC

USB-C Input Amps

.........................................

0.1 - 2.1 A

REDLITHIUM

™

USB Battery

Volts

........................................................................

4 DC

Operating Temperature

Battery and Charger

.......

40°F to 104°F (4°C to 40°C)

Battery and Tool

.............

0°F to 149°F (-18°C to 65°C)

Cable (USB-C) Cat. No.

.............................

42-44-1210

BATTERY

WARNING

To reduce the risk of fire, personal in

-

jury, and product damage due to a short

circuit, never immerse your tool, battery pack or

charger in fluid or allow a fluid to flow inside them.

Corrosive or conductive fluids, such as seawater,

certain industrial chemicals, and bleach or bleach

containing products, etc., can cause a short circuit.

Maintenance and Storage

Do not expose your battery or cordless tools to water or

rain, or allow them to get wet. This could damage the tool

and battery. Do not use oil or solvents to clean or lubricate

your battery. The plastic casing will become brittle and

crack, causing a risk of injury.

Store batteries at room temperature away from mois-

ture. Do not store in damp locations where corrosion of

terminals may occur. As with other battery types, per-

manent capacity loss can result if the pack is stored for

long periods of time at high temperatures (over 120°F).

MILWAUKEE Li-Ion batteries maintain their charge during

storage longer than other battery types. After about a year

of storage, charge the battery as normal.

WARNING

To reduce the risk of injury or explosion,

never burn or incinerate a battery pack

even if it is damaged, dead or completely discharged.

When burned, toxic fumes and materials are created.

Disposing of MILWAUKEE Li-Ion Battery

MILWAUKEE Li-Ion batteries are more environmentally

friendly than some other types of power tool batteries.

Always dispose of your battery according to federal, state

and local regulations. Contact a recycling agency in your

area for recycling locations.

Even discharged batteries contain some energy. Before

disposing, use electrical tape to cover the terminals to

prevent the battery from shorting, which could cause a

fire or explosion.

RBRC Battery Recycling Seals

The RBRC™ Battery Recycling Seals (see "Symbology")

on your batteries indicate that MILWAUKEE has arranged

for the recycling of that battery with the Rechargeable

Battery Recycling Corporation (RBRC). At the end of your

battery's useful life, return the battery to a MILWAUKEE

Branch Office/Service Center or the participating retailer

nearest you. For more information, visit the RBRC web

site at www.rbrc.org.

USB RECHARGEABLE

BOLT™ HEADLAMP

WARNING

Use and charge only

REDLITHIUM

™

USB

batteries in this

USB

rechargeable

headlamp. Other types of batteries may cause per

-

sonal injury and damage.

Inserting the Battery

1. Twist to open the battery cap.

2. Line up the battery

arrow with light

arrow, and fully

insert the battery.

3. Replace the battery cap and twist to close.

Charging the Battery

1. Plug your USB-C cable into a power source such as

an AC wall adaptor, computer or car port. Charge rates

may vary depending on the power source’s maximum

output.

2. Lift the rubber cover to expose the USB-C port.

Insert the USB-C plug into the USB-C port.

NOTE

: Always close the USB cover when light is not

charging to maintain dust and moisture protection.

3. The power button will display the charging status:

Red Pulsing:

Charging, 0-49% charged

Yellow Pulsing:

Charging, 50-99% charged

Green Solid:

100% charged

If the power button flashes red and green, check that

the battery is fully seated into the bay. Remove the

battery and reinsert. If the light continues to flash red

and green, the battery may be extremely hot or cold,

or wet. Allow the battery to cool down, warm up, or dry

out and then reinsert. If the problem persists, contact

a MILWAUKEE service facility.

Assembly

CAUTION

To reduce the risk of injury, do not look

directly into the light when the light is on.

1. Slide the BOLT

™

headlamp mounting bracket onto the

front of the hard hat/helmet until it clicks into place, as

shown in Fig. 1.

2. Open the cam locks on the rear BOLT

™

battery pack,

as shown in Fig. 2.

3. Slide the rear BOLT

™

battery pack bracket onto the

rear of the hard hat/helmet, as shown in Fig. 3.

4. Close the cam locks on the rear BOLT

™

battery pack to

secure and ensure both brackets engage the retention

cleat of the hard hat/helmet.

BOLT

™

REDLITHIUM™ USB HEADLAMP

LAMPE FRONTALE USB BOLT™ REDLITHIUM™

LÁMPARA PARA CABEZA USB BOLT™ REDLITHIUM™

IMPORTANT SAFETY

INSTRUCTIONS

- SAVE THESE INSTRUCTIONS -

WARNING

READ AND UNDERSTAND ALL

INSTRUCTIONS.

Failure to follow

all instructions listed below, may result in electric shock,

fire and/or serious personal injury.

1. S

AVE THESE INSTRUCTIONS -

This manual con

-

tains important safety and operating instructions

for the REDLITHIUM

™ USB battery and

USB re-

chargeable light.

2.

CAUTION

Use and charge only

REDLITHIUM™

USB batteries in this USB rechargeable

light. Do not use counterfeit, aftermarket, or "knock

-

off" batteries or chargers. Do not wire a battery pack

to a power supply plug or car cigarette lighter.

3.

Before using the battery and light, read this opera

-

tor’s manual and all labels on the battery and light.

4.

Use only with listed/certified

ITE

power supply.

5.

Avoid dangerous environments.

Do not charge bat-

tery in rain, snow, damp or wet locations.

Do not use

battery or charger in the presence of explosive atmos-

pheres (gaseous fumes, dust or flammable materials)

because sparks may be generated when inserting or

removing battery, possibly causing fire.

6.

Charge in a well-ventilated area.

Do not block charger

vents. Keep them clear to allow proper ventilation. Do not

allow smoking or open flames near a charging battery.

Vented gases may explode.

7.

Maintain charger cord.

When unplugging charger, pull

plug rather than cord. Never carry charger by its cord.

Keep cord from heat, oil and sharp edges. Make sure

cord will not be stepped on, tripped over or subjected to

damage or stress. Do not use charger with damaged cord

or plug. Have a damaged charger replaced immediately.

8.

Use only recommended attachments.

9.

Always unplug charger before cleaning or main

-

tenance.

10.

Do not burn or incinerate batteries.

Batteries may

explode. Toxic fumes and materials are created when

batteries are burned.

11.

Do not crush, drop, or damage

battery pack. Always

securely contain battery packs during transport. Do

not use a battery that has received a sharp blow,

been dropped, run over, or damaged in any way (e.g.,

pierced with a nail, hit with a hammer, stepped on, in

a vehicle accident).

12.

Do not disassemble.

If it is damaged, take it to a

MILWAUKEE service facility.

13.

Battery chemicals cause serious burns.

Never allow

contact with skin, eyes, or mouth. If a damaged battery

leaks battery chemicals, use rubber or neoprene gloves

to dispose of it. If skin is exposed to battery fluids, wash

with soap and water and rinse with vinegar. If eyes

are exposed to battery chemicals, immediately flush

with water for 20 minutes and seek medical attention.

Remove and dispose of contaminated clothing.

14.

Do not short circuit.

A short-circuited battery pack

may cause fire, personal injury, and product dam

-

age. A battery pack will short circuit if a metal object

makes a connection between the positive and neg-

ative contacts on the battery pack. Do not place a

battery pack near anything that may cause a short

circuit, such as coins, keys or nails in your pocket.

15.

Do not allow fluids to flow into battery pack.

Cor-

rosive or conductive fluids, such as seawater, certain

industrial chemicals, and bleach or bleach containing

products, etc., can cause a short circuit.

16.

Store your battery pack and charger in a cool, dry

place.

Do not store battery where temperatures may

exceed 120°F (50°C) such as in direct sunlight, a ve-

hicle or metal building during the summer.

17.

To reduce the risk of injury, close supervision is

necessary

when an appliance is used near children.

18.

Store idle light out of reach of children.

Warm lights

can become hazardous in the hands of children.

19.

Know your light.

Read this manual carefully to learn

your light's applications and limitations as well as po-

tential hazards associated with this type of light.

20.

Maintain labels and nameplates.

These carry im-

portant information. If unreadable or missing, contact

a

MILWAUKEE service facility for a free replacement.

SYMBOLOGY

Volts

Direct Current

Amps

Do not stare at the operating light source.

Read Operator's Manual

Power Button Mode button

Universal Serial Bus Type-C (USB-C)

Properly Recycle Batteries

CAUTION

Surface is hot. Avoid contact.

Operation

Press the power button

to turn the light on and off.

Press the mode button to cycle through the light intensities.

The power button will display the battery capacity:

Green Solid:

50-100% remaining

Yellow Solid:

11-49% remaining

Red Solid:

3-10% remaining

Red Flashing:

0-3% remaining

During use, when the battery charge reaches 3%, the

main LED will flash, indicating up to 5 minutes of runtime

remains. Prior to immediate shutdown, the main LED

will flash 3 times, then the tool will shutdown. Remaining

runtime may be less than 5 minutes if the light is turned

on when battery capacity is already 0-3%.

Overheating: If the flashlight starts to dim and the indicator

light flashes red and green, the battery may be too hot.

Normal function will resume when the battery has cooled.

WARNING

To reduce the risk of injury, always

unplug the charger and remove the

battery from the charger before performing any main

-

tenance. The charger and battery have no internal

serviceable parts. Never disassemble the battery or

charger.

Maintenance and Storage

Store your charger in a cool, dry place.

As a general practice, it is best to unplug battery char-

gers and remove batteries when not in use. No battery

damage will occur, however, if the charger and battery

are left plugged in.

WARNING

To reduce the risk of injury and damage,

never immerse your battery or charger

in liquid or allow a liquid to flow inside them.

Cleaning

Clean out dust and debris from charger vents and elec-

trical contacts by blowing with compressed air. Use only

mild soap and a damp cloth to clean the battery and

charger, keeping away from all electrical contacts. Certain

cleaning agents and solvents are harmful to plastics and

other insulated parts. Some of these include gasoline,

turpentine, lacquer thinner, paint thinner, chlorinated

cleaning solvents, ammonia and household detergents

containing ammonia. Never use flammable or combustible

solvents around batteries, charger, or tools.

SERVICE - UNITED STATES

1-800-SAWDUST

(1.800.729.3878)

Monday-Friday, 7:00 AM - 6:30 PM CST

or visit

www.milwaukeetool.com

Contact Corporate After Sales Service Technical Support

with technical, service/repair, or warranty questions.

Email: [email protected]

Become a Heavy Duty Club Member at

www.milwaukeetool.com to receive important notifications

regarding your tool purchases.

SERVICE - CANADA

Milwaukee Tool (Canada) Ltd

1.800.268.4015

Monday-Friday, 7:00 AM - 4:30 PM CST

or visit www.milwaukeetool.ca

LIMITED WARRANTY - USA & CANADA

Every MILWAUKEE REDLITHIUM USB battery and charger* is warranted to the original

purchaser only to be free from defects in material and workmanship. Subject to certain

exceptions, MILWAUKEE will repair or replace repair a REDLITHIUM USB battery or

charger which, after examination, is determined by MILWAUKEE to be defective in material

or workmanship for a period of two (2) years after the date of purchase unless otherwise

noted. Return of the REDLITHIUM USB battery or charger to a MILWAUKEE factory Service

Center location or MILWAUKEE Authorized Service Station, freight prepaid and insured,

is required. For the proper shipping procedure of battery packs, contact 1.800.SAWDUST

(1.800.729.3878), or go to www.milwaukeetool.com. A copy of the proof of purchase

should be included with the return product. This warranty does not apply to damage that

MILWAUKEE determines to be from repairs made or attempted by anyone other than

MILWAUKEE authorized personnel, misuse, alterations, abuse, normal wear and tear,

lack of maintenance, or accidents.

Normal Wear: This warranty does not cover repair or replacement when normal use has

exhausted the life of a part including, but not limited to charging cables, and wall plugs.

*This warranty does not cover any cordless product sold with the REDLITHIUM USB battery

and/or charger. There are separate and distinct warranties available for these products.

ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DE-

SCRIBED HEREIN IS A CONDITION OF THE CONTRACT FOR THE PURCHASE OF

EVERY MILWAUKEE PRODUCT. IF YOU DO NOT AGREE TO THIS CONDITION, YOU

SHOULD NOT PURCHASE THE PRODUCT.

IN NO EVENT SHALL MILWAUKEE BE

LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES,

OR FOR ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGED

TO BE AS A CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY

PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF PROFITS.

SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL

OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY

NOT APPLY TO YOU. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER

EXPRESS WARRANTIES, WRITTEN OR ORAL. TO THE EXTENT PERMITTED BY

LAW, MILWAUKEE DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING WITHOUT

LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR

A PARTICULAR USE OR PURPOSE; TO THE EXTENT SUCH DISCLAIMER IS NOT

PERMITTED BY LAW, SUCH IMPLIED WARRANTIES ARE LIMITED TO THE DURATION

OF THE APPLICABLE EXPRESS WARRANTY AS DESCRIBED ABOVE. SOME STATES

DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO

THE ABOVE LIMITATION MAY NOT APPLY TO YOU, THIS WARRANTY GIVES YOU

SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY

FROM STATE TO STATE.

This warranty applies to product sold in the U.S.A. and Canada only.

Please consult the Find a Service Center Search in the Parts & Service section of

MILWAUKEE’s website www.milwaukeetool.com or call 1.800.SAWDUST (1.800.729.3878)

to locate your nearest MILWAUKEE factory Service Center location.

LIMITED WARRANTY - USA & CANADA

All other MILWAUKEE Personal Lighting Products* (see exceptions below) are warranted

to the original purchaser only to be free from defects in material and workmanship. Subject

to certain exceptions, MILWAUKEE will repair or replace any part on a personal lighting

product which, after examination, is determined by MILWAUKEE to be defective in material

or workmanship for the lifetime of such personal lighting products.

Normal Wear: This warranty does not cover repair or replacement when normal use has

exhausted the life of a part including, but not limited to clips, straps, charging cables, wall

plugs, and rubber gaskets. This warranty does cover the LED in the personal lighting

products, subject to the limitations herein.

*This warranty does not cover Cordless Battery Packs or Chargers. There are separate

and distinct warranties available for these products.

Return of all personal lighting products to a MILWAUKEE factory Service Center location or

MILWAUKEE Authorized Service Station, freight prepaid and insured, is required.

A copy of

the proof of purchase should be included with the return product.

The above warranties do

not apply to damage that MILWAUKEE determines to be from repairs made or attempted by

anyone other than MILWAUKEE authorized personnel, misuse, alterations, abuse, normal

wear and tear, lack of maintenance, accidents, or caused by alkaline batteries.

ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DE-

SCRIBED HEREIN IS A CONDITION OF THE CONTRACT FOR THE PURCHASE OF

EVERY MILWAUKEE PRODUCT. IF YOU DO NOT AGREE TO THIS CONDITION, YOU

SHOULD NOT PURCHASE THE PRODUCT. IN NO EVENT SHALL MILWAUKEE BE

LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES,

OR FOR ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGED

TO BE AS A CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY

PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF PROFITS.

SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR

CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT

APPLY TO YOU. THE ABOVE WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL

OTHER EXPRESS WARRANTIES, WRITTEN OR ORAL. TO THE EXTENT PERMITTED

BY LAW, MILWAUKEE DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING WITHOUT

LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR USE OR PURPOSE; TO THE EXTENT SUCH DISCLAIMER IS NOT PER-

MITTED BY LAW, SUCH IMPLIED WARRANTIES ARE LIMITED TO THE DURATION OF

THE APPLICABLE EXPRESS WARRANTIES AS DESCRIBED ABOVE. SOME STATES

DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO

THE ABOVE LIMITATION MAY NOT APPLY TO YOU, THESE WARRANTIES GIVES YOU

SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY

FROM STATE TO STATE.

These warranties apply to product sold in the U.S.A. and Canada only.

Please consult the Find a Service Center Search in the Parts & Service section of

MILWAUKEE’s website www.milwaukeetool.com or call 1.800.SAWDUST (1.800.729.3878)

to locate your nearest MILWAUKEE factory Service Center location.

INSTRUCTIONS DE

SÉCURITÉ IMPORTANTES

- CONSERVER CES

INSTRUCTIONS -

AVERTISSEMENT

LIRE ET COMPRENDRE

TOUTES LES INSTRUC-

TIONS.

Le non-respect des instructions ci-après peut

entraîner des chocs électriques, des incendies et/ou

des blessures graves.

1. GARDER CES INSTRUCTIONS -

Ce manuel con

-

tient des instructions importantes concernant la

sécurité et le fonctionnement de la lampe recharge

-

able par USB et la batterie USB REDLITHIUM™.

2.

ATTENTION

Utiliser et charger uniquement les

batteries USB REDLITHIUM™

avec cette lampe rechargeable USB. Ne pas utiliser

des batteries ou des chargeurs contrefaits, falsifiés

ou « truqués ». Ne pas relier un bloc-piles à une

prise secteur ou à un allume-cigare.

3.

Avant d’utiliser la batterie et la lampe, veiller à

lire ce manuel d’utilisation ainsi que toutes les

étiquettes sur la batterie et la lampe.

4.

Utiliser uniquement avec une source d’alimentation

ITE listée/certifiée.

5.

Éviter les environnements dangereux.

Ne pas

charger la pile sous la pluie, la neige ou dans des en-

droits humides ou mouillés. Ne pas utiliser la pile ou le

chargeur dans un endroit propice aux explosifs (fumées

gazeuses, poussières ou matériaux inflammables), car

l’insertion ou le retrait de la pile pourrait donc créer des

étincelles, ce qui risque de causer un incendie.

6.

Charger dans un espace bien ventilé.

Ne pas

bloquer les évents d’aération du chargeur. S’assurer

que les évents ne sont pas obstrués afin de permettre

une ventilation correcte. Ne laisser ni de fumées ni de

flammes sans contrôle auprès d’une pile en cours de

chargement. Les gaz à évent pourront exploser.

7.

Bien conserver le cordon du chargeur.

Lorsque le

chargeur est débranché, tirer sur la fiche et pas sur le

cordon. Ne jamais prendre le chargeur par le cordon.

Garder le cordon à l’écart de la chaleur, de l’huile et

des objets tranchants. S’assurer que le cordon ne se

trouve pas dans un endroit où il risque d’être piétiné,

accroché, endommagé ou maltraité. Ne pas utiliser le

chargeur si le cordon ou la fiche sont endommagés.

Remplacer immédiatement tout chargeur endommagé.

8.

Utiliser uniquement les accessoires recommandés.

9.

Débranchez toujours le chargeur avant de le net

-

toyer ou l’entretenir.

10.

Ne pas brûler ou incinérer les batteries.

Les batter-

ies pourront exploser. Des vapeurs et des matériaux

toxiques se produisent à partir de la brûlure des

batteries.

11.

Ne pas écraser, laisser tomber ou endommager

le bloc-piles. Toujours mettre les blocs-piles dans un

conteneur sûr durant le transport. Ne pas utiliser une

batterie qui a subi un choc violent, a été écrasé ou

endommagé d’une manière quelconque (par exemple,

s’il a été percé par un clou, frappé par un marteau ou

piétiné durant un accident de voiture).

12.

Ne pas désassembler le produit.

Si jamais il

est endommagé, le confier à un centre de service

MILWAUKEE.

13.

Les produits chimiques entraînent des brûlures

graves.

Ne permettez pas qu’ils entrent en contact

avec la peau, les yeux ni la bouche. Si de la pile

endommagée des produits chimiques se coulent,

utilisez des gants en caoutchouc ou néoprène pour

se débarrasser d’elle. Si la peau est exposée à des

fluides de la pile, lavez-la avec du savon et de l’eau et

rincez-la avec du vinaigre. Si les yeux sont exposés

aux produits chimiques de la pile, lavez-les avec

pleine de l’eau pendant 20 minutes et consultez un

médecin. Retirez les vêtements contaminés et se

débarrassez d’eux.

14.

Ne pas court-circuiter.

Un bloc-piles court-circuité

pourra mener un incendie, des blessures physiques

et endommager le produit. Un bloc-piles court-cir-

cuitera si un objet métallique établit une connexion

entre les contacts positif et négatif du bloc-piles. Met-

tre le bloc-piles à l’écart de tout ce qui pourra causer

un court-circuit, tel que des pièces de monnaie, des

clés ou des clous dans votre poche.

15.

Ne pas laisser les fluides entrer dans le bloc-

piles.

Les fluides corrosifs et conducteurs, tels que

l’eau de mer, quelques produits chimiques industri-

els et solutions d’eau de Javel ou d’autres produits

ayant de l’hypochlorite, etc., pourront provoquer des

courts-circuits.

16.

Entreposer votre bloc-piles et votre chargeur

dans un endroit frais et sec.

Ne pas entreposer la

batterie dans des endroits où la température peut dé-

passer 50ºC (120ºF), par exemple, un endroit exposé

directement à la lumière du soleil, un véhicule ou une

construction en métal pendant l’été.

17.

Afin de réduire le risque de blessures, supervision

étroite est requise

quand un appareil est utilisé près

d’enfants.

2

3

4

1

8

6

9

7

8

5

Fig. 2

1. BOLT™ headlamp mounting bracket

2. LED light

3.

Power button/fuel gauge

4. Mode button

5. Cam locks

6. Battery cap

7. USB-C port

8. BOLT™ retention cleat

9. BOLT™ battery pack bracket

1. Support de montage pour lampe frontale BOLT™

2. Témoin à DEL

3.

Touche d’alimentation/voyant de charge

4. Touche de mode

5. Verrous de came

6. Couvercle de batterie

7. Port USB-C

8. Barrette de rétention BOLT™

9. Support pour bloc-piles BOLT™

1. Soporte de montaje de la lámpara para cabeza BOLT™

2. Luz LED

3.

Botón de encendido/indicador de carga

4. Botón de modo

5.

Levas de fijación

6. Tapa de la batería

7. Puerto USB-C

8. Abrazadera de retención BOLT™

9. Soporte de batería BOLT™

Milwaukee Tool 2118-21 Operators Manual

Milwaukee Tool 2118-21 Manual

Milwaukee Tool 2118-21 manual content summary: