Motorola SX600TPR User Guide

Setting the Volume

Press and hold

while rotating

until you reach a comfortable

listening level.

1. Rotate

clockwise to increase the volume.

2. Rotate

counterclockwise to decrease the volume.

Do not hold the radio close to your ear. If the volume is set to an

uncomfortable level, it could hurt your ear.

FRS/GMRS Recreational Two-Way Radios

FV600 Series

User’s Guide

Safety and General Information

FCC Licensing Information

Control Buttons

Display Screen Guide

KEM-PK10711

Important Information on Safe and Efficient Operation

Read This Information Before Using Your Radio.

The information provided in this document supersedes the general

safety information in user guides published prior to December 1, 2002.

Transmit and Receive Procedure

Your two-way radio contains a transmitter and a receiver. To control

your exposure and ensure compliance with the general

population/uncontrolled environment exposure limits, always adhere to

the following procedure:

•

Transmit no more than 50% of the time.

•

To receive calls, release the PTT button.

•

To transmit (talk), press the Push to Talk (PTT) button.

Transmitting 50% of the time, or less, is important because the radio

generates measurable RF energy exposure only when transmitting (in

terms of measuring standards compliance).

Exposure to Radio Frequency Energy

Your Motorola two-way radio complies with the

following RF energy exposure standards and guidelines:

•

United States Federal communications Commission, Code of Federal

Regulations; 47CFR part 2 sub-part J

•

American National Standards Institute (ANSI)/Institute of Electrical

and Electronic Engineers (IEEE) C95. 1-1992

•

Institute of Electrical and Electronics Engineers (IEEE) C95.1-1999

Edition

•

International Commission on Non-Ionizing Radiation Protection

(ICNIRP) 1998

Getting Started

Installing the Batteries:

Your radio uses three AA Alkaline batteries and beeps when the

batteries are low.

1. Turn the radio off.

2. With the back of the radio facing you, lift the battery latch up to

release the battery cover and remove the cover.

3. Insert three AA Alkaline batteries as shown on the inside of the

battery compartment.

4. Reposition the battery cover and press down to secure.

NOTE:

The FV600 model radio can use a NiMH rechargeable battery

instead of three AA batteries.

Installing the NiMH Battery Pack:

1. Follow step 2 above to remove the battery cover.

2. Remove the battery pack from the clear plastic bag.

Do not

disassemble or unwrap the battery pack.

3. Insert the NiMH battery pack so the “This Side Up” is showing.

4. Reposition the battery cover and press down to secure.

Battery Meter

The battery icon shows the battery charge level, from full

to empty

. When the battery is empty, the radio chirps periodically

after releasing

(Low Battery Alert). The radio powers off when the

voltage drops below a predetermined level to protect the rechargeable

battery.

Note:

Remove the batteries before storing your radio for extended

periods of time. Batteries corrode over time and may cause permanent

damage to your radio.

Talking and Listening

To communicate, all radios in your group must be set to the same

channel and Interference Eliminator Code.

1. To talk, press and hold

.

2. When you are finished talking, release

.

For maximum clarity, hold the radio two to three inches away from your

mouth and speak directly into the microphone. Do not cover the

microphone while talking.

Talk Range

Your radio is designed to maximize performance and improve

transmission range. Do not use the radios closer than five feet apart.

Monitor Button

Pressing and holding

for three seconds allows you to listen to the

volume level of the radio when you are not receiving. This allows you

to adjust the volume, if necessary. You can also use

to check for

activity on the current channel before you talk.

Push to Talk

Timeout Timer

To prevent accidental transmissions and save battery life, the radio

emits a continuous warning tone and stops transmitting if you press

PTT for 60 continuous seconds.

Using the Desk Stand Charger (Optional Accessory)

The desk stand charger provides drop-in charging convenience for

NiMH batteries and can be placed on any flat surface, such as a desk

or workbench. Charge the NiMH battery overnight (at least 16 hours)

before using it for the first time. After the initial charge, an empty

battery is fully charged within 14 hours.

1. Follow steps 1-5 from “Installing the NiMH Battery Pack” above.

2. Plug the AC power supply into the plug on the desk stand.

3. Plug the AC power supply into a standard wall outlet.

4. Remove the battery pocket inserts from the charger pockets.

5. With a radio facing forward, slide it into one of the charging pockets.

Notes

•

The light on the AC power supply will glow continuously when

radio/battery is inserted.

•

When moving between hot and cold temperatures, do not charge the

battery until the battery temperature acclimates (usually about 20

minutes).

•

For optimal battery life, remove the radio or battery from the charger

within 16 hours. Do not store the radio in the charger.

•

Turn radio off while in charging tray.

Turning Your Radio On and Off

Turn

clockwise to turn the radio on and counterclockwise to turn

the radio off.

1. The radio chirps and briefly shows all features icons available on

your radio.

2. The display then shows the current channel, code and features that

are selected.

Initial Setup

Selecting a Channel

Your radio has 22 channels.

Channels 8-14 are FRS 0.5 watt only and

all other channels are 1 watt GMRS.

When the radio is on a 0.5 watt

channel,

displays.

When the radio is on a 1 watt channel,

displays.

1. With the radio on, press

. The current channel flashes.

2. Press

or

to

select a channel.

3. Press

to confirm your selection or

to continue set up.

For More Information

For further information, you may call Motorola at 1-800-638-5119 (U.S.

and Canada) or visit us on the Internet at http://www.motorola.com.

Setting and Transmitting Call Tones

Your radio can transmit different call tones to other radios in your group

so you can alert them that you want to talk. You have 10 call tones from

which to choose.

To set a call tone:

1. With the radio on, short press

until the current call tone setting

flashes and

appears.

2. Press

or

to change and hear the call tone.

3. Press

to set the new call tone or

to continue set up.

To transmit your call tone to other radios set to the same channel and

Interference Eliminator Code as your radio, press

.

Note:

Setting the call to 0 disables the call tone feature.

Interference Eliminator Code

Interference Eliminator Codes help minimize interference by providing

you with a choice of code combinations. Your radio has 121

Interference Eliminator Codes. Codes 1 - 38 are the standard codes that

appear on other FRS/GMRS radios. Codes 39 - 121 are additional codes

added for superior interference protection.

1. Short press

until the code starts to flash.

2. Press

or

to select the code.

3. Press

to save the code setting or

to continue set up.

You can set a different code for each channel using this procedure. An

extended press of

or

allows you to scroll through the

Interference Codes rapidly so you can quickly reach the code you

want.

Note:

You must set the Interference Eliminator Code to 0 on a radio that

uses Interference Eliminator Codes to communicate with radios that do

not have Interference Eliminator Codes.

Select 0 for “no tone, no code”

and OFF will flash on your radio’s display.

Hands-Free Use Without Accessories (iVOX)

You can use the iVOX feature to transmit, hands-free without the need

for any voice activation accessories. Once iVOX is turned on, the radio

detects your voice and transmits when you speak.

1. Short press

until

appears on the display. The current

setting On/Off will flash.

2. Press

or

to select On or Off.

3. Press

to set or

to continue set up.

Setting the Sensitivity Level When in VOX or iVOX Mode

Adjusting the radio’s sensitivity level helps minimize the possibility of

unintended noises triggering a transmission and helps the radio pick up

soft voices.

1. Short press

after setting iVOX. VOX will still appear.

2. Press

or

to select the sensitivity level.

3. Press

to set or

to continue set up.

Use

to:

• Turn radio on/off.

• Increase or

decrease volume

LED Indicator

Light

Use Push to Talk

to:

•

Talk

• Save a setting

Use

to:

• Transmit call tone

Speaker

Microphone

Accessory Jack

Use

and

to:

• Scroll through

menus

•

Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure

to Radiofrequency Electromagnetic Fields in the Frequency Range

from 3 KHz to 300 GHz, 1999

•

Australian communications Authority Radiocommunications

(Electromagnetic Radiation—Human Exposure) Standard, 2003

•

ANATAL ANNEX to Resolution No. 303 of July 2, 2002 “Regulation of

limitation of exposure to electrical, magnetic and electromagnetic

fields in the radio frequency range between 9 KHz and 300GHz” and

“Attachment to resolution #303 from July 2, 2002”

To assure optimal radio performance and make sure human exposure

to radio frequency electromagnetic energy is within the guidelines set

forth in the above standards, always adhere to the following

procedures.

Portable Radio Operation and EME Exposure

Antenna Care

Use only the supplied or an approved replacement antenna.

Unauthorized antennas, modifications, or attachments could damage

the radio and may violate FCC regulations.

Do NOT hold the antenna when the radio is “IN USE.” Holding the

antenna affects the effective range.

Body-Worn Operation

To maintain compliances with FCC/Health Canada RF exposure

guidelines, if you wear a radio on your body when transmitting, always

place the radio in a Motorola-supplied or approved clip, holder, holster,

case or body harness for this product. Use of non-Motorola-approved

accessories may exceed FCC/Health Canada RF exposure guidelines.

If you do not use one of the Motorola-supplied or approved body-worn

accessories and are not using the radio held in the normal use

position,

ensure the radio and its antenna are at least 1 inch (2.5 cm)

from your body when transmitting.

Battery Charger Safety Instructions:

Save these Instructions

1. Do not expose the charger to rain or snow.

2. Do not operate or disassemble the charger if it has received a sharp

blow, or has been dropped or damaged in any way.

3. Never alter the AC cord or plug provided with the unit. If the plug will

not fit the outlet, have the proper outlet installed by a qualified

electrician. An improper condition can result in a risk of electric

shock.

4. To reduce the risk of damage to the cord or plug, pull the plug rather

than the cord when disconnecting the charger from the AC receptacle.

5. To reduce the risk of electric shock, unplug the charger from the outlet

before attempting any maintenance or cleaning.

6. Use of an attachment not recommended or sold by Motorola may

result in a risk of fire, electric shock or personal injury.

7. Make sure the cord is located so it will not be stepped on, tripped over

or subjected to damage or stress.

8. An extension cord should not be used unless absolutely necessary.

Use of an improper extension cord could result in a risk of a fire

and/or electric shock. If an extension cord must be used, make sure

that:

•

The pins on the plug of the extension cord are the same number, size

and shape as those on the plug of the charger.

•

The extension cord is properly wired and in good electrical condition.

•

The cord size is 18 AWG for lengths up to 100 feet, and 16 AWG for

lengths up to 150 feet.

9. The supply cord of this charger cannot be replaced. If the cord is

damaged, call Motorola Product Services at 1-800-353-2729 in the USA

or 1-888-390-6456 TTY (text telephone).

Potentially Explosive Atmospheres

Turn off your radio prior to entering any area with a potentially explosive

atmosphere. Only radio types that are especially qualified should be

used in such areas as “Intrinsically Safe.” Do not remove, install or

charge batteries in such areas. Sparks in a potentially explosive

atmosphere can cause an explosion or fire resulting in bodily injury or

even death.

Note:

The areas with potentially explosive atmospheres referred to

above include fueling areas such as below decks on boats, fuel or

chemical transfer or storage facilities, areas where the air contains

chemicals or particles (such as grain, dust or metal powders) and any

other area where you would normally be advised to turn off your vehicle

engine. Areas with potentially explosive atmospheres are often—but not

always—posted.

Blasting Caps and Areas

To avoid possible interference with blasting operations, turn off your

radio when you are near electrical blasting caps, in a blasting area, or in

areas posted “Turn off two-way radios.” Obey all signs and instructions.

Operational Cautions

Antennas

Do not use any portable radio that has a damaged antenna. If a damaged

antenna comes into contact with your skin, a minor burn can result.

Batteries

All batteries can cause property damage and/or bodily injury such as

burns if a conductive material—like jewelry, keys or beaded chains—

touch exposed terminals. The conductive material may complete an

electrical circuit (short circuit) and become quite hot. Exercise care in

handling any charged battery, particularly when placing it inside a

pocket, purse or other container with metal objects.

Your Motorola radio operates on General Mobile Radio Service (GMRS)

frequencies and is subject to the Rules and Regulations of the Federal

Communications Commission (FCC). The FCC requires that all operators

using GMRS frequencies obtain a radio license before operating their

equipment. To obtain the FCC forms, please request Form

605

and

159

,

which includes all of the forms and instructions you will need.

If you wish to have the document faxed or mailed, or if you have

questions, please use the following contact information:

You may also visit the FCC’s Web site at http://www.fcc.gov.

Changes or modifications not expressly approved by Motorola may void

the user’s authority granted by the FCC to operate this radio and should

not be made. To comply with FCC requirements, transmitter adjustments

should be made only by or under the supervision of a person certified as

technically qualified to perform transmitter maintenance and repairs in

the provide land mobile and fixed services as certified by an organization

representative of the user of those services. Replacement of any

transmitter component (crystal, semiconductor, etc.) not authorized by

the FCC equipment authorization for this radio could violate FCC rules.

Note:

Use of this radio outside the country where it was intended to be

distributed is subject to government regulations and may be prohibited.

Data Operation

If applicable, when using any data feature of the radio with or without

an accessory cable,

position the radio and its antenna at least one

inch (2.5 cm) from the body

.

Approved Accessories

For a list of approved Motorola accessories, visit out Web site at

www.Motorola.com.

Electromagnetic Interference/Compatibility

Note:

Nearly every electronic device is susceptible to electromagnetic

interference (EMI) if inadequately shielded, designed or otherwise

configured for electromagnetic compatibility. This device complies with

Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful interference; and

2. This device must accept any interference received, including

interference that may cause undesired operation.

Facilities

To avoid electromagnetic interference and/or compatibility conflicts,

turn off your radio in any facility where posted notices instruct you to

do so. Hospitals or health care facilities may be using equipment that is

sensitive to external RF energy.

Aircraft

When instructed to do so, turn off your radio when onboard on aircraft.

Any use of a radio must be in accordance with applicable regulations

per airline crew instructions.

Medical Devices – Pacemakers

The Advanced Medical Technology Association recommends that a

minimum separation of 6 inches (15 cm) be maintained between a

handheld wireless radio and a pacemaker. These recommendations are

consistent with the independent research by and recommendations of

the U.S. Food and Drug Administration.

People with pacemakers should:

•

ALWAYS keep the radio more than 6 inches (15 cm) from their

pacemaker when the radio is turned ON.

•

Not carry the radio in the breast pocket.

•

Use the ear opposite the pacemaker to minimize the potential for

interference.

•

Turn the radio OFF immediately if there is any reason to suspect that

interference is taking place.

Medical Devices – Hearing Aids

Some digital wireless radios may interfere with some hearing aids. In

the event of such interference, you may want to consult your hearing

aid manufacturer to discuss alternatives.

Other Medical Devices

If you use any other personal medical device, consult the manufacturer

of your device to determine if it is adequately shielded from RF energy.

Your physician may be able to assist you in obtaining this information.

Safety and General Use While Driving

Check the laws and regulations regarding the use of radios in the area

where you drive, and always obey them. If you do use your radio while

driving, please:

•

Give full attention to driving and to the road.

•

Use hands-free operation, if available.

•

Pull off the road and park before making or answering a call if driving

conditions so require.

Do not place a portable radio in the area over an air bag or in the air

bag deployment area. Air bags inflate with great force. If a portable

radio is placed in the air bag deployment area and the air bag inflates,

the radio may be propelled with great force and cause serious injury to

occupants of the vehicle.

For a Fax:

Contact the Fax-On

Demand system

1-202-418-0177

For Mail Service:

Call the FCC Forms

Hotline

1-800-418-FORM (3676)

If You Have Questions

about the FCC License:

Call the FCC

1-888-CALL-FCC

(225-5322)

Channel

Frequency

Description

Channel

Frequency

Description

1

462.5625

MHz

GMRS/FRS

12

467.6625

MHz

FRS

2

462.5875

MHz

GMRS/FRS

13

467.6875

MHz

FRS

3

462.6125

MHz

GMRS/FRS

14

467.7125

MHz

FRS

4

462.6375

MHz

GMRS/FRS

15

462.5500

MHz

GMRS

5

462.6625

MHz

GMRS/FRS

16

462.5750

MHz

GMRS

6

462.6875

MHz

GMRS/FRS

17

462.6000

MHz

GMRS

7

462.7125

MHz

GMRS/FRS

18

462.6250

MHz

GMRS

8

467.5625

MHz

FRS

19

462.6500

MHz

GMRS

9

467.5875

MHz

FRS

20

462.6750

MHz

GMRS

10

467.6125

MHz

FRS

21

462.7000

MHz

GMRS

11

467.6375

MHz

FRS

22

462.7250

MHz

GMRS

VOX

i

QT

ON

OFF

PTT

PTT

PTT

PTT

PTT

PTT

PTT

PTT

PTT

–

+

–

+

–

+

–

+

–

+

–

+

–

+

MENU

MENU

MENU

MENU

MENU

MENU

PTT

MENU

MENU

MENU

MENU

Use

to:

• Scan to see if

anyone is on the

selected channel

Use

to:

• Select Menu

options

• Exit the Menu

(when pressed

while in a Menu)

• Lock and unlock

the keypad (when

held down and

not in a Menu)

– Battery Meter

Numbers for

Channel,

Call Tone

Numbers for

Codes

– Scan

VOX

i

VOX

i

MENU

– Hands-Free Use

Without

Accessories

– Call Tone,

Keypad Tone

– Channel Indicator

– Lock

– Talk Confirmation Tone

(Roger Beep)

ON

OFF

– On/Off for

each feature

QT

– Noise Filtering

Channels and Frequencies

3 =

High Sensitivity

for quiet environments

2 =

Medium Sensitivity

for most environments

1 =

Low Sensitivity

for noisy environments

Note:

When you connect a VOX accessory, the radio is automatically

set to the last chosen sensitivity level.

See Special Features section on Accessories.

Continued on back

FV600

®

2.

1.

3.

4.

5.

6.

7.

8.

9.

10.

MON

MON

MON

MON

Motorola SX600TPR User Guide

Motorola SX600TPR Manual

Motorola SX600TPR manual content summary: