NEC LED-E015i-135IN Installation Kit Manual

NEC LED-E015i-135IN Manual

Get NEC LED-E015i-135IN PDF manuals and user guides View all NEC LED-E015i-135IN manuals
Add to My Manuals
Save this manual to your list of manuals

NEC LED-E015i-135IN manual content summary:

  • NEC LED-E015i-135IN | Installation Kit Manual - Page 1
    Installation and Maintenance manual LED Display Kit [Models for indoor use] LED-E012i-108 LED-E012i-217 LED-E015i-135 LED-E018i-162 LED-E025i-217 MODELS: LED-E012i, LED-E015i, LED-E018i, LED-E025i
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 2
    2. Installation Setup...10 3. Wiring...22 4. Installing the pixel card 27 Screen Configuration English-29 Image Setting English-38 Maintenance English-40 Troubleshooting English-43 1. Display problems...43 2. State monitoring using the software 44 Specifications English-49 Diagram English-50
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 3
    About the Symbols To ensure safe and proper use of the product, this manual uses a number of symbols to prevent injury to you and others as well described below. Be sure to understand them thoroughly before reading this manual. WARNING CAUTION Failing to heed this symbol and handling the product
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 4
    In case foreign matter has entered into the product, immediately disconnect the power supply and stop using the product. After the installation, if a problem such as loose screws occurs, immediately ask a technician or your retailer for repair. Do not put objects into the product. Otherwise, it may
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 5
    near heaters. This product is designed to be used indoors. Do not use it outdoors. Otherwise, it may cause a malfunction. This product can only be serviced in the country where it was purchased. English - 3
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 6
    About the LED lamps LED lamps are sensitive to static electricity and surge voltage, which may damage their components and decrease their reliability. Take measures against static electricity during the installation. Do not touch the LED display areas. The LED lamps may absorb and hold moisture
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 7
    Contents The supplied parts are as follows. In case one of these parts is missing or damaged, contact the retailer. Parts Bottom frame Specifications Quantity LED-E012i-108 LED-E015i-135 LED-E018i-162 LED-E012i-217 LED-E025i-217 1 1 1 2 Bottom frame connecting part - - - 1 Bottom
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 8
    ) 4 connector 48 56 100 144 25 36 90 132 1 1 - - - - 20 30 5 6 - - 2 - 1 6 1 1 6 12 72 256 64 240 - 1 1 - - 4 48 56 8 8 8 - - 8 1 16 WAGO (3pcs) 2 3 6 8 USB flash memory Safety Manual Packing list 1 1 1 1 1 1 1 1 1 1 1 1 English - 6
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 9
    Parts Name 1 34 5 2 6 7 5 34 1 Pixel card 2 Cabinet 3 LAN cable input/output 4 LAN cable input (not used with this product) 5 Power cord input/output 6 Hub board 7 Power unit English - 7
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 10
    by enough people to ensure safety. • Make sure that the beams or the other structures to which the product is installed have enough strength to support the weight of the product, and make sure that the product is securely fixed. • Do not install directly the product to a surface that has not
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 11
    % & D min. distance to ceiling 500 mm E min. distance to floor 700 mm English - 9
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 12
    2. Installation Setup 2.1 Mark the positions of the anchor points on the wall • Mark the positions of the holes you will make for the anchor points (refer to the figures below and the "Anchor points number and positions" table on the next page). • Before making the holes, check the verticality of
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 13
    337.5 mm 337.5 mm 337.5 mm 337.5 mm 337.5 mm 337.5 mm 337.5 mm 1200 mm 1200 mm 1200 mm Anchor points positions: LED-E012i-217, LED-E025i-217 Anchor points number and positions Frame set LED-E012i-108 Anchor points (horizontal x vertical) Horizontal distance Vertical distance Anchor size 2×4
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 14
    2.3 Install the mounting bars (1) Install the mounting bars on the anchor points on the wall. (2) Check the distance between the mounting bars using the alignment bars. Alignment bar 1200 mm Alignment bar Alignment bar Alignment bar 1800 mm LED-E012i-108 Alignment bar Alignment bar 1200 mm
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 15
    Alignment bar Alignment bar 1200 mm 1200 mm 1200 mm LED-E012i-217, LED-E025i-217 (3) Check the evenness using a spirit level and the alignment bars together. Adjust the positions if required. M10 screws Wall mounted: Mounting bar installation (LED-E015i-135) English - 13
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 16
    2.4 Install the bottom frame Remove the bottom frame cover and install the bottom frame using M6 screws. How to remove the bottom cover (1) Remove the screws securing the bottom frame cover. (2) Raise the front of the bottom frame cover. (3) Pull the bottom frame cover toward you to remove it.
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 17
    M6 screws Bottom frame When using the 8 x 8 frame set, use the bottom frame connecting part to install the bottom frame. Bottom frame connecting screw (PM3) (8 red circles) Bottom frame connecting screw (KM3) (8 blue circles) Bottom frame connecting part 2.5 Install the cabinet hanger pins to the
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 18
    2.6 Install the cabinets Hook the hanger pins, which have been inserted into the cabinets, into the holes on the mounting bars starting from the lowest row. Fix temporarily the cabinets of the first row to the bottom frame. English - 16
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 19
    Hook the hanger pins of the cabinets of the second row to the mounting bars. Secure the LED cabinets together using connection screws for LED modules. Do not tighten the screws completely. After you have installed two rows of cabinets, align the surfaces of the cabinets using the cabinet alignment
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 20
    How to connect the power cord (1) Raise the lever. (2) Insert the wire. (3) Return the lever to its previous position. Wire sizes compatible with the power connector (WAGO) are as follows. Solid core: φ1.6 to 2.0 mm IV 7-stranded core: 2.0 to 3.5 mm2 WARNING Pay attention to the wire colors of
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 21
    Insert the slot nuts inside the over frame into the holes of the connection screws for the LED modules and fix them with M3 screws. Slot nuts Install the corner parts to the over frame (top) and install it on the top of the cabinets. Slot nut installation locations LED-E012i-108 LED-E015i-135
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 22
    2.7 Assembly diagrams LED-E012i-108 1200 1449.75 1356 2412 2400 AAAA AAAA AAAA AAAA 1456 700 800 166.75 1449.75 Through hole for the LAN cable 600 600 600 LED-E015i-135 1800 1787.3 1693.5 50 3012 3000 AAAAA AAAAA AAAAA AAAAA AAAAA 1793.5 166.8 700 800 1787.3 Through hole for the
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 23
    LED-E018i-162 1200 1200 2124.75 2031 3612 3600 AAAAAA AAAAAA AAAAAA AAAAAA AAAAAA AAAAAA 2131 700 800 166.75 2124.75 2806 Through hole for the LAN cable 600 600 600 600 600 LED-E012i-217, LED-E025i-217 1200 1200 1200 2799.75 2706 50 4812 4800 AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 24
    3. Wiring LED-E012i-108 RV RV RV RV RV RV RV RV RV RV RV RV RV RV RV RV PSU PSU PSU PSU PSU PSU PSU PSU PSU PSU PSU PSU PSU PSU PSU PSU by client Control PC by client HDMI 1 LED-E015i-135 RV RV RV RV RV RV RV RV RV RV RV RV RV RV RV LED Controller Main RV RV
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 25
    100V/15A or 200V/15A 100V/15A or 200V/15A 100V/15A or 200V/15A 100V/15A or 200V/15A 100V/15A or 200V/15A 100V/15A or 200V/15A 100V/15A or 200V/15A 100V/15A or 200V/15A LED-E012i-217 RV RV RV RV RV RV RV RV RV RV RV RV RV RV RV RV RV RV RV RV RV RV RV RV RV RV RV RV RV
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 26
    (1) Power cord connection Connect the power cords to the LED modules on the first row. The power cord must be securely plugged. Connect the power cords between the LED modules. English - 24
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 27
    (2) LAN cable connection Connect the LAN cables for the signal between the LED modules. Use the through holes to pass the cables between the modules. Six through holes for the LAN cables LAN connectors [Connection example 1] Connecting from bottom to top using multiple ports English - 25
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 28
    [Connection example 2] Connecting all the LED modules using a single LAN cable LAN cable from the LED controller Hub board Connect the cable to the LAN connector on the left. Do not use the LAN connector on the right. Insert the LAN cable into the through hole and connect it to the LAN connector on
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 29
    the back of the pixel card and on the hub board are orientated toward the same direction, and that the two guide pins of the pixel card are aligned to the guide holes of the cabinet (two for each pixel card). The pixel card is secured by the 14 magnets on each
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 30
    Magnet Guide pin Magnet Guide hole (3) Check that the pixel card stays securely in place and then turn the maintenance tool off. English - 28
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 31
    Screen Configuration Check that all the connections are completed, and then turn on the LED modules and the LED controller. Power distributor LED controller CONTROL INPUT OUTPUT Control signal Video signal WARNING Pay attention to the wire colors of the power cord when connecting the cord. If
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 32
    Setting the screen configuration Perform the setting using the LCT-Mars control software by Novastar. Log in with the administrator privileges. Display the login screen as follows: User(U) → Advanced Synchronous System UserLogin(A). Enter the password ("admin" by default) to log in with the
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 33
    Select "Standard Screen" under "Screen Type" (d). The settings in "Sending Card Number" (e) and "Ethernet Port No." (f) vary depending on the connected LED controller. (d) (h) (e) (f) (g) (i) Enter the value in the table below under "Receiving Card Size" (g). Product name LED-E012i LED-E015i
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 34
    [Configuration example] The setting values are given for the following example where 16 LED-E012i modules (pixel pitch of 1.25 mm) are installed in a 4 (columns) x 4 (rows) configuration. CONTROL INPUT OUTPUT (1) With a pixel pitch of 1.25 mm, enter Width=480 and Height=270 under "Receiver Card
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 35
    (2) Since the configuration is 4 (columns) x 4 (rows), enter Columns=4 and Rows=4. A 4 (columns) x 4 (rows) screen configuration is displayed. English - 33
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 36
    (3) If multiple LED controllers are used, select the number of the connected LED controllers. Since only one controller is used in this example, it is not necessary to set "Sending Card Number" (e). (4) Configure the connection. (4)-1 Connecting from bottom to top using multiple ports The system is
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 37
    Follow the same procedure for Port3 and Port4. English - 35
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 38
    (4)-2 Connecting all the LED modules using a single LAN cable The system is connected to port 1 of the LED controller. Select "1" (port 1) under "Ethernet Port No." (f). Click (select) the connection pattern under "Quick Connection" (i). Since the modules are connected from the bottom left to the
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 39
    The selection is done automatically to obtain the screen below. (j) (k) (l) (5) Save the settings. (a) Click the "Send to HW" button (j). When the dialog box indicating that the process finished successfully is displayed, click OK. (b) Check that the image is correctly displayed, and then click
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 40
    Image Setting You can adjust the brightness, the gamma correction value, and the color temperature. Click "Brightness" on the top screen to display the following window. (b) (a) Click "Advanced Settings" to expand the screen. (c) (e) (d) English - 38
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 41
    Click "Advanced Settings" ( ) (a) to expand the setting screen. (1) Brightness Set the brightness of the screen using the slider (b). Increasing the value increases the brightness. (2) Gamma correction Set the gamma correction value using the slider (c). Increasing the value makes the dark parts of
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 42
    maintenance tool is fully charged before starting the work. Pixel card falls if the battery runs out. Hold the pixel card with your hand to support in case it falls. CAUTION: Do not turn the maintenance tool off until you hold the pixel card. Otherwise, the pixel card may fall and
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 43
    Removing the power supply Disconnect the LAN cable connected to the hub board. Remove the 10 screws securing the hub board, and then remove the hub board. Then, remove the two screws securing the terminal cover. Hub board Terminal cover Disconnect the power cables connected to the power supply and
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 44
    Removing the receiving card Remove the receiving card from the hub board. Remove the four screws securing the receiving card, and then remove the receiving card from the hub board. Receiving card English - 42
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 45
    Troubleshooting 1. Display problems Problem Nothing is displayed on all the LED modules. Nothing is displayed on one LED module. No image is displayed on one pixel card. Control (communication)
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 46
    2. State monitoring using the software In case of a problem, you will be able to determine the location where it occurred by monitoring the state of the system. 2-1 Display under normal conditions The display is
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 47
    with the input signal to the LED controller When the display is red, there is a problem with the LED controller. To display more details, click "Monitoring", and then click "Sending card" on the screen that is displayed. No video signal is
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 48
    display more details, click "Monitoring", and then click "Receiving card" on the screen that is displayed. In the example shown on the left, the following problems must be considered. - Signal loss between the screen of the 1st row 3rd column and the screen of the 1st row 2nd column → Check the
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 49
    with the internal temperature of the LED modules There is a problem with the LED module operation. To display more details, click "Monitoring", and then the brightness setting. If changing the brightness setting could not solve the problem, contact your retailer or the Customer Service. English - 47
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 50
    (4) Communication problem When the display is grey, the communication is not established. → Check that the USB cable is connected. → Check that the LED controller is turned on. English - 48
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 51
    Specifications Models for indoor use Module LED configuration Pixel pitch Number of displayed pixels (resolution/module) Brightness Contrast ratio Brightness adjustment range Gamma correction Color temperature Viewing angle Signal interface Signal input Signal output Power supply Power
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 52
    Diagram LED-E012i / LED-E015i / LED-E018i / LED-E025i 337.5 29 600 43.0 32.0 16.0 4-M5 8-M5 13.0 37.0 37.5 English - 50 (Unit: mm)
  • NEC LED-E015i-135IN | Installation Kit Manual - Page 53
    LED-E012i / LED-E015i / LED-E018i / LED-E025i Cabinet alignment bracket 8 4-Φ5 35 35 6 (Unit: mm) English - 51
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
Installation and
Maintenance manual
LED Display Kit
[Models for indoor use]
LED-E012i-108
LED-E012i-217
LED-E015i-135
LED-E018i-162
LED-E025i-217
MODELS: LED-E012i, LED-E015i, LED-E018i, LED-E025i