NEC LED-FE015i3 User Manual

NEC LED-FE015i3 Manual

Get NEC LED-FE015i3 PDF manuals and user guides View all NEC LED-FE015i3 manuals
Add to My Manuals
Save this manual to your list of manuals

NEC LED-FE015i3 manual content summary:

  • NEC LED-FE015i3 | User Manual - Page 1
    User's Manual LED Module [Models for indoor use] LED-FE012i3 LED-FE015i3 LED-FE019i3 MODELS: LED-FE012i3, LED-FE015i3, LED-FE019i3
  • NEC LED-FE015i3 | User Manual - Page 2
    ; however, should you notice any questionable points, errors or omissions, please contact us. (4) The image shown in this manual is indicative only. If there is inconsistency between the image and the actual product, the actual product shall govern. (5) Notwithstanding articles (3) and (4), we will
  • NEC LED-FE015i3 | User Manual - Page 3
    About the Symbols To ensure safe and proper use of the product, this manual uses a number of symbols to prevent injury to you and others as well described below. Be sure to understand them thoroughly before reading this manual. WARNING CAUTION Failing to heed this symbol and handling the product
  • NEC LED-FE015i3 | User Manual - Page 4
    In case foreign matter has entered into the product, immediately disconnect the power supply and stop using the product. After the installation, if a problem such as loose screws occurs, immediately ask a technician or your retailer for repair. Do not put objects into the product. Otherwise, it may
  • NEC LED-FE015i3 | User Manual - Page 5
    from your body before touching the Pixel cards by touching an aluminum sash, a door knob, or some other metal object. This product can only be serviced in the country where it was purchased. English - 3
  • NEC LED-FE015i3 | User Manual - Page 6
    display areas. When you install the product or when you use it for the first time after leaving it unused for a long time, follow the instructions below. The LED lamps may absorb and hold moisture during the LED module installation or if not used for a long time. Therefore, in such cases
  • NEC LED-FE015i3 | User Manual - Page 7
    Contents The supplied parts are as follows. In case one of these parts is missing or damaged, contact the retailer. CAUTION Depending on the system you ordered, there is a cabinet without the upper connector. [Cabinet] [Pixel card] 8 cards per cabinet English - 5
  • NEC LED-FE015i3 | User Manual - Page 8
    connection, 1000 mm for horizontal connection) [Cabinet alignment bracket] [Screw for Adjustment plates] [Connection screw for LED modules] [USB drive] Contains the data, the user's manual (this document), and the control software for the product you have purchased. English - 6
  • NEC LED-FE015i3 | User Manual - Page 9
    Name Interface connectors 12 Signal input/output 34 Power input (output) 5 Status lamp (red) 6 Status lamp (blue) 7 Status lamp (green) 8 Test button 9 Handle 0 Guide pin Rear Description Input and output connectors for the signal and AC power. To input the signal from the LED controller or the
  • NEC LED-FE015i3 | User Manual - Page 10
    A) The connectors are equipped on the top and bottom sides. There are guide pins on the top. Power hub board Power unit Receiving card (2) When (Type B) There are no connectors on the top side. There are no guide pins. Power hub board Power unit Receiving card (3) When connecting a LAN
  • NEC LED-FE015i3 | User Manual - Page 11
    Specifications LED-FE012i3 LED-FE015i3 LED-FE019i3 LED configuration Pixel pitch Number of displayed pixels (resolution/module) Brightness Contrast ratio Brightness adjustment range Gamma correction Color temperature Viewing angle Signal interface Signal input Signal output Power
  • NEC LED-FE015i3 | User Manual - Page 12
    Diagram LED-FE012i3, LED-FE015i3, LED-FE019i3 608 49 342 Rear 4 x M8 18.5 24 294 24 44 520 44 (Unit: mm) English - 10
  • NEC LED-FE015i3 | User Manual - Page 13
    Adjustment plate 28 4-Φ8.5 75 75 10 (Unit: mm) English - 11
  • NEC LED-FE015i3 | User Manual - Page 14
    to EU directive 2006/66/EC and amendments, the battery can't be disposed improperly. The battery shall be separated to collect by local service. Service & Support in Europe Please contact: Sharp NEC Display Solutions Europe GmbH. Landshuter Allee 12-14, D-80637 München Phone: + 49 (0) 89/99699-0 Fax
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
User’s Manual
LED Module
[Models for indoor use]
LED-FE012i3
LED-FE015i3
LED-FE019i3
MODELS: LED-FE012i3, LED-FE015i3, LED-FE019i3