Home » NEC Manuals » Projectors » NEC NP-PA521U » Manual Viewer

NEC NP-PA521U User's Manual

NEC NP-PA521U Manual

View all NEC NP-PA521U manuals

Add to My Manuals
Save this manual to your list of manuals

NEC NP-PA521U manual content summary:

NEC NP-PA521U | User's Manual - Page 1
Projector PA721X/PA621X/PA671W PA621U/PA571W/PA521U PA722X/PA622X/PA672W PA622U/PA572W/PA522U User's Manual Model No. NP-PA721X/NP-PA621X/NP-PA671W/NP-PA621U/NP-PA571W/ NP-PA521U/NP-PA722X/NP-PA622X/NP-PA672W/NP-PA622U/NPPA572W/NP-PA522U
NEC NP-PA521U | User's Manual - Page 2
the trademarks or registered trademarks of their respective holders. NOTES (1) The contents of this user's manual may not be reprinted in part or whole without permission. (2) The contents of this user's manual are subject to change without notice. (3) Great care has been taken in the preparation of
NEC NP-PA521U | User's Manual - Page 3
this manual carefully before using your NEC projector and keep the manual handy ARE HIGH-VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol warns the user provided. The information should be read carefully to avoid problems. WARNING: TO PREVENT FIRE OR SHOCK, DO NOT
NEC NP-PA521U | User's Manual - Page 4
Solutions of America, Inc. in this manual. Failure to comply with this government please contact your supplier. Important Safeguards These safety instructions are to ensure the long life of your addition, the ceiling must be strong enough to support the projector and the installation must be in
NEC NP-PA521U | User's Manual - Page 5
a wire or screwdriver into your projector. If something should fall into your projector, disconnect it immediately and have the object removed by a qualified service personnel. • Do not place any objects on top of the projector. • Do not touch the power plug during a thunderstorm. Doing so can cause
NEC NP-PA521U | User's Manual - Page 6
the projector does not operate normally when you follow the instructions described in this user's manual. - If the projector has been dropped or the cabinet • Do not send the projector in the soft case by parcel delivery service or cargo shipment. The projector inside the soft case could be damaged.
NEC NP-PA521U | User's Manual - Page 7
Please dispose according to Local, State or Federal Laws. Lamp Replacement • Use the specified lamp for safety and performance. • To replace the lamp, follow all instructions provided on page 159. • Be sure to replace the lamp and filter when the message [THE LAMP HAS REACHED THE END OF ITS US- ABLE
NEC NP-PA521U | User's Manual - Page 8
Information Health precautions to users viewing 3D images Before viewing, be sure to read health care precautions that may be found in the user's manual included with your LCD shutter eyeglasses or your 3D compatible content such as DVDs, video games, computer's video files and the like. To avoid
NEC NP-PA521U | User's Manual - Page 9
the Box?...1  Introduction to the Projector 2 Congratulations on Your Purchase of the Projector 2 Features you'll enjoy 2 About this user's manual 3  Part Names of the Projector 4 Front/Top...4 Rear...5 Control Panel/Indicator Section 6 Terminal Panel Features 7  Part Names of the Remote
NEC NP-PA521U | User's Manual - Page 10
Table of Contents  Using the Optional Remote Mouse Receiver (NP01MR 30  Correcting Horizontal and Vertical Keystone Distortion [CORNERSTONE 32 Cornerstone...32  Displaying Two Pictures at the Same Time 35 Selecting the PIP or PICTURE BY PICTURE Mode [MODE 35 [POSITION]...36  Preventing the
NEC NP-PA521U | User's Manual - Page 11
Table of Contents [IMAGE OPTIONS 94 [VIDEO]...98 6 Menu Descriptions & Functions [SETUP 100 [BASIC]...100 [MENU]...102 [INSTALLATION(1 103 [INSTALLATION(2 106 [OPTIONS(1)]...108 [OPTIONS(2)]...110 7 Menu Descriptions & Functions [INFO 112 [USAGE TIME]...112 [SOURCE(1)]...113 [SOURCE(2)]...113 [
NEC NP-PA521U | User's Manual - Page 12
Cabinet Dimensions 198  Mounting the cable cover (sold separately 199  Pin Assignments of D-Sub COMPUTER Input Connector 200  Troubleshooting...201 Indicator Messages 201 Common Problems & Solutions 203 If there is no picture, or the picture is not displayed correctly 205 6 PC Control Codes
NEC NP-PA521U | User's Manual - Page 13
) (For Other countries than North America: 7N8N1551 and 7N8N1562) • Quick Setup Guide (For North America: 7N8N1571) (For Other countries than North America: 7N8N1571 and 7N8N1581) NEC Projector CD-ROM User's manual (PDF) and the utility software (7N951971) For North America only Registration card
NEC NP-PA521U | User's Manual - Page 14
technicians in order to ensure proper operation and reduce the risk of bodily injury. In addition, the ceiling must be strong enough to support the projector and the installation must be in accordance with any local building codes. Please consult your dealer for more information. Features you
NEC NP-PA521U | User's Manual - Page 15
Media Player 11's "media sharing" function. • CRESTRON ROOMVIEW compatibility The projector supports CRESTRON ROOMVIEW, allowing multiple devices connected in the network to be managed and controlled from a computer. About this user's manual The fastest way to get started is to take your time and do
NEC NP-PA521U | User's Manual - Page 16
 Part Names of the Projector Front/Top The lens is sold separately. The description below is for when the NP13ZL lens is mounted. 1. Introduction Lens Shift Dial (vertical/horizontal) (→ page 18) Zoom Lever/Zoom Ring (→ page 21) Remote Sensor (→ page 9) Ventilation (outlet) Heated air is
NEC NP-PA521U | User's Manual - Page 17
, 155) Cable cover connection (right and left) Screw holes and grooves for the optional cable cover (→ page 212) * This security slot supports the MicroSaver ® Security System. 1. Introduction Remote Sensor (located on the front and the rear) (→ page 9) Ventilation (outlet) Heated air is exhausted
NEC NP-PA521U | User's Manual - Page 18
Control Panel/Indicator Section 2 345 8 6 9 11 1. (POWER) Button (→ page 14, 25) 2. POWER Indicator (→ page 13, 14, 25, 214) 3. STATUS Indicator (→ page 214) 4. LAMP Indicator (→ page 159, 215) 5. TEMP. Indicator (→ page 215) 6. SOURCE Button (→ page 16) 7. AUTO ADJ. Button (→ page 24) 8.
NEC NP-PA521U | User's Manual - Page 19
Terminal Panel Features 10 11 12 1 2 34 1. Introduction 89 7 13 14 5 6 15 16 1. HDMI 1 IN Connector (Type A) (→ page 144, 145, 149) 2. HDMI 2 IN Connector (Type A) (→ page 144, 145, 149) 3. DisplayPort IN Connector (→ page 144) 4. BNC IN [R/Cr/CV, G/Y/Y, B/Cb/C, H, V] Connectors (BNC × 5)
NEC NP-PA521U | User's Manual - Page 20
 Part Names of the Remote Control 1 3 5 4 8 9 12 13 16 17 19 22 23 25 27 30 31 33 35 37 40 38 43 44 1. Infrared Transmitter (→ page 9) 2. POWER ON Button (→ page 14) 3. STANDBY Button (→ page 25) 4. FREEZE Button (→ page 27) 5. BLANK Button (→ page XXX) 6. MUTE Button (→ page XXX) 7. AV-MUTE
NEC NP-PA521U | User's Manual - Page 21
1. Introduction Battery Installation 1 2 3 Press the catch and remove Install new ones (AA). Ensure Slip the cover back over the batteries until it the battery cover. that you have the batteries' polar- snaps into place. ity (+/−) aligned correctly. NOTE: Do not mix different types of
NEC NP-PA521U | User's Manual - Page 22
to use a wireless LAN. NOTE: • Image Express Utility Lite and Image Express Utility for Mac do not support "Meeting Mode" which is provided in Image Express Utility 2.0. Download service For the update information about these software programs, visit our website: URL: http://www.nec-display.com/dl
NEC NP-PA521U | User's Manual - Page 23
Windows Vista Ultimate Windows Vista Enterprise Windows XP Home Edition Service Pack 3 or later Windows XP Professional Service Pack 3 or later • Only 32-bit version • Windows power-saving function is not supported. • Windows 7/Windows Vista Pentium M 1.2 GHz equivalent or higher required Dual
NEC NP-PA521U | User's Manual - Page 24
2. Projecting an Image (Basic Operation) This section describes how to turn on the projector and to project a picture onto the screen.  Flow of Projecting an Image Step 1 • Connecting your computer / Connecting the power cord (→ page 13) Step 2 • Turning on the projector (→ page 14) Step 3 •
NEC NP-PA521U | User's Manual - Page 25
2. Projecting an Image (Basic Operation)  Connecting Your Computer/Connecting the Power Cord 1. Connect your computer to the projector. This section will show you a basic connection to a computer. For information about other connections, see "(2) Making Connections" on page 143. Connect the
NEC NP-PA521U | User's Manual - Page 26
 Turning on the Projector 1. Remove the lens cap. 2. Projecting an Image (Basic Operation) 2. Press the (POWER) button on the projector cabinet or the POWER ON button on the remote control. The POWER indicator will turn to blue and the projector will become ready to use. TIP: • When the message
NEC NP-PA521U | User's Manual - Page 27
2. Projecting an Image (Basic Operation) Note on Startup screen (Menu Language Select screen) When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one of the 27 menu languages. To select a menu language, follow these steps: 1. Use the ,
NEC NP-PA521U | User's Manual - Page 28
2. Projecting an Image (Basic Operation)  Selecting a Source Selecting the computer or video source NOTE: Turn on the computer or video source equipment connected to the projector. Detecting the Signal Automatically Press the SOURCE button once. The projector will search for the available input
NEC NP-PA521U | User's Manual - Page 29
2. Projecting an Image (Basic Operation)  Adjusting the Picture Size and Position Use the lens shift dial, the adjustable tilt foot lever, the zoom lever/zoom ring and the focus ring to adjust the picture size and position. In this chapter drawings and cables are omitted for clarity. Adjusting the
NEC NP-PA521U | User's Manual - Page 30
2. Projecting an Image (Basic Operation) Adjusting the vertical position of a projected image (Lens shift) CAUTION Perform the adjustment from behind or from the side of the projector. Adjusting from the front could expose your eyes to strong light which could injure them. Lens shift dial (
NEC NP-PA521U | User's Manual - Page 31
2. Projecting an Image (Basic Operation) TIP: • The diagram below shows the lens shift adjustment range for the PA722X/PA721X/PA622X/PA621X (projection mode: desktop front). To raise the projection position higher than this, use the tilt feet. (→ page 21) • For the PA672W/PA671W/PA572W/PA571W/PA622U
NEC NP-PA521U | User's Manual - Page 32
2. Projecting an Image (Basic Operation) Applicable lens: NP11FL With the NP11FL lens, adjust the focus and picture distortion. Preparations: Turn the lens shift dials (vertical and horizontal) on the projector to return the lens shift to the center. Approximate lens center position (explained here
NEC NP-PA521U | User's Manual - Page 33
2. Projecting an Image (Basic Operation) Zoom Turn the zoom lever or zoom ring clockwise and counterclockwise. - The separately sold NP11FL lens does not have a zoom ring. Zoom ring Adjusting the Tilt Feet 1. Turn the left and right tilt feet to adjust. The tilt feet lengthen and shorten when
NEC NP-PA521U | User's Manual - Page 34
2. Projecting an Image (Basic Operation)  Correcting Keystone Distortion When the projector is not exactly perpendicular to the screen, keystone distortion occurs. To overcome it, you can use the "Keystone" function, a digital technology that can adjust for keystone-type distortion, resulting in a
NEC NP-PA521U | User's Manual - Page 35
5. Repeat steps 2 and 4 to correct keystone distortion. 2. Projecting an Image (Basic Operation) 6. After completing Keystone correction, press the EXIT button. The Keystone screen will disappear. • To perform Keystone correction again, press the GEOMETRIC. button to display the Keystone screen
NEC NP-PA521U | User's Manual - Page 36
not be displayed correctly. • If the Auto Adjust operation cannot optimize the computer signal, try to adjust [HORIZONTAL], [VERTICAL], [CLOCK], and [PHASE] manually. (→ page 94, 95)  Turning Up or Down Volume Sound level from the speaker can be adjusted. Increase volume Decrease volume TIP: When
NEC NP-PA521U | User's Manual - Page 37
 Turning off the Projector 2. Projecting an Image (Basic Operation) To turn off the projector: 1. First, press the (POWER) button on the projector cabinet or the POWER OFF button on the remote control. The [POWER OFF / ARE YOU SURE ? / CARBON SAVINGS- SESSION 0.000[g-CO2]] message will appear.
NEC NP-PA521U | User's Manual - Page 38
2. Projecting an Image (Basic Operation)  After Use Preparation: Make sure that the projector is turned off. 1. Unplug the power cord. 2. Disconnect any other cables. • Remove the USB memory if it is inserted into the projector. 3. Mount the lens cap on the lens. 4. Before moving the projector,
NEC NP-PA521U | User's Manual - Page 39
3. Convenient Features 1 Turning off the Image and Sound Press the AV-MUTE button to turn off the image, sound, beep sound for a short period of time. Press again to restore the image and sound. The projector's power-saving function will work 10 seconds after the image is turned off. As a result,
NEC NP-PA521U | User's Manual - Page 40
2. Press the button. The area of the magnified image will be moved 3. Convenient Features 3. Press the D-ZOOM (−) button. Each time the D-ZOOM (−) button is pressed, the image is reduced. NOTE: • The image will be enlarged or reduced at the center of the screen. • Displaying the menu will cancel
NEC NP-PA521U | User's Manual - Page 41
3. Convenient Features Checking Energy-Saving Effect [CARBON METER] This feature will show energy-saving effect in terms of CO2 emission reduction (kg) when the projector's [ECO MODE] is set to [OFF], or [ON]. This feature is called as [CARBON METER]. There are two messages: [TOTAL CARBON SAVINGS]
NEC NP-PA521U | User's Manual - Page 42
3. Convenient Features  Using the Optional Remote Mouse Receiver (NP01MR) The optional remote mouse receiver enables you to operate your computer's mouse functions from the remote control. It is a great convenience for clicking through your computer-generated presentations. Connecting the remote
NEC NP-PA521U | User's Manual - Page 43
Operating your computer's mouse from the remote control You can operate your computer's mouse from the remote control. 3. Convenient Features PAGE / Button: Buttons: L-CLICK Button: R-CLICK Button: scrolls the viewing area of the window or to move to the previous or next slide in PowerPoint
NEC NP-PA521U | User's Manual - Page 44
3. Convenient Features  Correcting Horizontal and Vertical Keystone Distortion [CORNERSTONE] Use the 3D Reform feature to correct keystone (trapezoidal) distortion to make the top or bottom and the left or right side of the screen longer or shorter so that the projected image is rectangular.
NEC NP-PA521U | User's Manual - Page 45
3. Convenient Features 7. Use the button to move the projected image frame as shown on the example. 8. Press the ENTER button. 9. Use the button to select another icon which points in the direction. On the Cornerstone adjustment screen, select [EXIT] or press the EXIT button on the remote control.
NEC NP-PA521U | User's Manual - Page 46
The adjustable ranges for 3D Reform are as follows: 3. Convenient Features PA722X/PA721X/PA622X/PA621X/PA672W/PA671W/PA572W/PA571W CORNERSTONE KEYSTONE HORIZONTAL Max. +/− 40° approx. VERTICAL Max. +/− 30° approx. PA622U/PA621U/PA522U/PA521U CORNERSTONE KEYSTONE HORIZONTAL Max. +/− 35° approx
NEC NP-PA521U | User's Manual - Page 47
side and the sub picture on the right side. • The main picture signal supports the COMPUTER 1, COMPUTER 2, and COMPUTER 3 connectors. The sub picture signal supports the VIDEO IN and S-VIDEO IN connectors. • The main picture supports an RGB signal with a resolution of 1280 × 1024 pixels or less. 35
NEC NP-PA521U | User's Manual - Page 48
PIP button again to return to the normal screen (single picture). TIP: • Selecting another source will return to the normal screen. • Selecting a source not supported for the main picture or the sub picture will return to the normal screen. [POSITION] This option allows you to select the position of
NEC NP-PA521U | User's Manual - Page 49
3. Convenient Features  Preventing the Unauthorized Use of the Projector [SECURITY] A keyword can be set for your projector using the Menu to avoid operation by an unauthorized user. When a keyword is set, turning on the projector will display the Keyword input screen. Unless the correct keyword is
NEC NP-PA521U | User's Manual - Page 50
3. Convenient Features 7. Type in the same combination of buttons and press the ENTER button. The confirmation screen will be displayed. 8. Select [YES] and press the ENTER button. The SECURITY function has been enabled. To turn on the projector when [SECURITY] is enabled: 1. Press the POWER button
NEC NP-PA521U | User's Manual - Page 51
To disable the SECURITY function: 1. Press the MENU button. The menu will be displayed. 3. Convenient Features 2. Select [SETUP] → [INSTALLATION(2)] → [SECURITY] and press the ENTER button. The OFF/ON menu will be displayed. 3. Select [OFF] and press the ENTER button. The SECURITY KEYWORD screen
NEC NP-PA521U | User's Manual - Page 52
3. Convenient Features  Controlling the Projector by Using an HTTP Browser Overview The HTTP Server function provides settings and operations for: 1. Setting for wired/wireless network (NETWORK SETTINGS) To use wireless LAN connection, the optional USB Wireless LAN Unit is required. (→ page 151) To
NEC NP-PA521U | User's Manual - Page 53
3. Convenient Features Handling of the Address for Operation via a Browser Regarding the actual address that is entered for the address or entered to the URL column when operation of the projector is via a browser, the host name can be used as it is when the host name corresponding to the IP address
NEC NP-PA521U | User's Manual - Page 54
3. Convenient Features PICTURE: Controls the video adjustment of the projector. BRIGHTNESS Increases the brightness adjustment value. BRIGHTNESS Decreases the brightness adjustment value. CONTRAST Increases the contrast adjustment value. CONTRAST Decreases the contrast adjustment value. COLOR
NEC NP-PA521U | User's Manual - Page 55
NETWORK SETTINGS 3. Convenient Features • SETTINGS WIRED or WIRELESS SETTING APPLY DHCP ON DHCP OFF IP ADDRESS SUBNET MASK GATEWAY WINS AUTO DNS ON AUTO DNS OFF Set for wired LAN or for wireless LAN. Apply your settings to wired LAN or wireless LAN. Automatically assign IP address, subnet mask,
NEC NP-PA521U | User's Manual - Page 56
SSID SITE SURVEY NETWORK TYPE SECURITY TYPE INDEX KEY USERNAME PASSWORD 3. Convenient Features Enter an identifier (SSID) for wireless LAN. Communication can be done only with equipment whose SSID matches SSID for your wireless LAN. Displays a list of available SSIDs for wireless LAN on site.
NEC NP-PA521U | User's Manual - Page 57
3. Convenient Features USE DIGITAL CERTIFICATE Select this if you use a digital certificate for WPA-EAP TKIP PEAP-MSCHAP v2/WPAEAP AES PEAP-MSCHAP v2/WPA2-EAP TKIP PEAP-MSCHAP v2/WPA2-EAP AES PEAP-MSCHAP v2. • NAME PROJECTOR NAME HOST NAME DOMAIN NAME Enter a name for your projector so that your
NEC NP-PA521U | User's Manual - Page 58
• NETWORK SERVICE PJLink PASSWORD HTTP PASSWORD AMX BEACON 3. Convenient Features Set a password for PJLink by Japan Business Machine and Information System Industries Association (JBMIA) in 2005. The projector supports all the commands of PJLink Class 1. Setting of PJLink will not be affected even
NEC NP-PA521U | User's Manual - Page 59
Enterprise The specifications recommended by Microsoft as the operation environment for Windows 7/Windows Vista should be satisfied. Wired LAN or wireless LAN environment that supports TCP/IP is required. High Color (16 bits) True Color (24 bits and 32 bits) * Setting with 256 colors or less is not
NEC NP-PA521U | User's Manual - Page 60
3. Convenient Features 2. Press the  or  button to select [NETWORK] and press the ENTER button. In the screen, the [APPLICATION MENU] menu is displayed. 3. From the [APPLICATION MENU] menu, select [NETWORK PROJECTOR]. The [PROJECTOR NAME/DISPLAY RESOLUTION/PASSWORD/URL] will be displayed. 48
NEC NP-PA521U | User's Manual - Page 61
3. Convenient Features Projecting the Image with Network Projector 1. Click [Start] from the desktop of Windows 7. 2. Click [All Programs]. 3. Click [Accessories]. 4. Click [Connect to a Network Projector]. When the [Permission Connect to a Network Projector] window appears, click [Yes.]. The "
NEC NP-PA521U | User's Manual - Page 62
3. Convenient Features 7. Input the password to the password input box displayed by the operation at step 3 on page 44. 8. Click [Connect]. The network projector function works and the screen of Windows 7 is projected from the projector. • If the resolution of your computer's screen is different
NEC NP-PA521U | User's Manual - Page 63
Vista Enterprise Windows XP Professional with Service Pack 3 (Note) • In this user's manual this feature is described using Windows cannot be used with the projector. • A wireless keyboard or mouse that supports Bluetooth cannot be used with the projector. • We do not warrant that the USB
NEC NP-PA521U | User's Manual - Page 64
3. Convenient Features Setting the password to the user account of Windows 7 TIP: If a password has been set for an account, the steps 1 to 9 can be skipped. 1. Click [Start] from the desktop of Windows 7. 2. Click [Control Panel]. 3. Click [Add or remove user accounts] displayed under [User
NEC NP-PA521U | User's Manual - Page 65
3. Convenient Features 4. Click [View status] displayed in blue on the right of [Local Area Connection] in the window. The [Local Area Connection Status] window appears. 5. Click [Details...]. Write down the value for "IPv4 IP Address" (xxx.xxx.xxx.xxx) displayed. 6. Click [Close]. 7. Click [X] at
NEC NP-PA521U | User's Manual - Page 66
3. Convenient Features 2. Press the  or  button to select [NETWORK] and press the ENTER button. The [NETWORK] menu will be displayed. 3. From the [NETWORK] menu, use the wireless keyboard to select [REMOTE DESKTOP CONNECTION]. The [REMOTE DESKTOP CONNECTION] window appears. 4. Operate the wireless
NEC NP-PA521U | User's Manual - Page 67
3. Convenient Features Exiting the Remote Desktop 1. Operate the wireless keyboard to click [Start] from the desktop screen projected by the projector. 2. Click [X] on the right of the start menu. The remote desktop function is stopped. 3. Press the SOURCE button of the projector to select an input
NEC NP-PA521U | User's Manual - Page 68
• Baseline JPEG: 10000 × 10000 • Progressive JPEG: 1280 × 1280 • GIF: 1280 × 1280 • Others: 4000 × 4000 • Some files supported by the above requirements may not be displayed. Supported movie files File name extension .mpg, .mpeg. Video compression/expansion method MPEG2 .wmv .mp4 VC-1/WMV9 H.264
NEC NP-PA521U | User's Manual - Page 69
computer, refer to the document or help file that comes with your Windows. - We do not warrant that the USB port of the projector will support all USB memories in the market. - Wait at least 5 seconds after disconnecting a USB memory device before reconnecting it and vice versa. The projector may
NEC NP-PA521U | User's Manual - Page 70
4. Using the Viewer Notices on shared folder and media server • Files from a shared folder or media server may not be projected if security or antivirus software is installed on your computer. • Open the following firewall ports: - Media server Port number 1900 2869 10243 10280-10284 Protocol
NEC NP-PA521U | User's Manual - Page 71
❷ Preparing presentation materials 4. Using the Viewer 1. Create your presentation materials and save them in a supported file format to your computer. • See page 81 for supported file formats. • Make sure that PowerPoint file is displayed on the Viewer before giving your real presentation. With
NEC NP-PA521U | User's Manual - Page 72
4. Using the Viewer ❸ Projecting images stored in a USB memory device This section explains the basic operation of the Viewer. The explanation provides the operational procedure when the Viewer toolbar is set to the factory default. Preparation: Before starting the Viewer, store images to the USB
NEC NP-PA521U | User's Manual - Page 73
4. Press the ▶ button to select "USB1" and press the ENTER button. The "USB1" thumbnail screen will be displayed. TIP: • For more information about thumbnail screen, see page 66. 5. Use the ▲▼◀ or ▶ button to select an icon. • The → (arrow) symbol on the right indicates there are more pages.
NEC NP-PA521U | User's Manual - Page 74
return to the thumbnail screen, press the EXIT button. NOTE: • Files with slideshow or animation effects may not be correctly displayed on the Viewer. See "Supported PowerPoint files" on page 57, 81. • Adobe PDF file The first page will be displayed. • The PDF file will fill the width of the screen
NEC NP-PA521U | User's Manual - Page 75
/AUTO) for slides of index file works in the following way: In case of [MANUAL] for [PLAY MODE] When you select [OPTIONS] → [SLIDE SETTING] → [PLAY MODE] → [MANUAL], index files will be set for manual playback in regardless of whether [INTERVAL] is set. In case of [AUTO] selected for [PLAY MODE
NEC NP-PA521U | User's Manual - Page 76
the Viewer Scroll bar Cursor (yellow) Folder icon [Drive list screen] Path information Drive information/File information Menu guide [Thumbnail screen] Operation button guide Control bar * The operation for still image differs from that for movie. [Slide screen] • Drive list screen Displays
NEC NP-PA521U | User's Manual - Page 77
stores index files. Path information Drive information Displays the location of a folder or file. [Example] USB1 314MB FREE/492MB Menu guide Operation button guide Displays the drive. Displays free space and capcity of a drive. (USB only) Displays the description of a selected menu. Displays
NEC NP-PA521U | User's Manual - Page 78
down or up. Displays the location of a folder or file. [Example] 005.jpg 5/200 11/03/2010 13:25:12 502KB Menu guide Operation button guide Selected folder name or file name Numbers and order of files in a folder (only when folder selected) Create/Change date: M/D/Y/H/M/B Displays the
NEC NP-PA521U | User's Manual - Page 79
• Slide screen (still image/movie) Plays a file selected from a list of thumbnails or icons. • For operating a Microsoft PowerPoint file and Adobe PDF file, see page 62. 4. Using the Viewer Control bar operation • The control bar will be displayed only when a still image (or index file) and a
NEC NP-PA521U | User's Manual - Page 80
Functions of movie control bar 4. Using the Viewer Name PREV FR PLAY/PAUSE FF NEXT TIME SIZE CLOSE END Description Goes back to the beginning of a movie file. • Goes back to the beginning of the previous movie file if executed immediately after being started playing. Fast-rewinds a movie file for
NEC NP-PA521U | User's Manual - Page 81
mark Description Displays the image with its aspect ratio in the projector's displayable maximum resolution. Displays the image in its actual size. Selects manual play. Selects auto play. Specifies interval time when [AUTO] is selected for PLAY MODE. Turns on or off the repeat function. TIP • To
NEC NP-PA521U | User's Manual - Page 82
device is inserted into the USB port of the projector and when [VIEWER] is selected for [SOURCE]. • Auto play starts for the first found file supporting the file type set up for Auto Play. The file will be searched in the drive root or lower level. • When [VIEWER] is selected for
NEC NP-PA521U | User's Manual - Page 83
• SORT SETTING Sets the order of displaying thumbnails or slides. 4. Using the Viewer Name SORT Options NAME (ABC..) NAME (ZYX..) EXT. (ABC..) EXT. (ZYX..) DATE (NEW) DATE (OLD) SIZE (BIG) SIZE (SMALL) Description Displays the files alphabetically by name in ascending order. Displays the files
NEC NP-PA521U | User's Manual - Page 84
the path for later use. • For sharing a folder, refer to your user guide or help file accompanied with your Windows computer. • Use a keyboard to give ] from the menu. • Digital signature (SMB signature) is not supported. Connecting the projector to the shared folder 1. Press the VIEWER button
NEC NP-PA521U | User's Manual - Page 85
2. Displays the [OPTIONS] menu. Press the ▼ button to select the 4. Using the Viewer (OPTIONS) icon and press the ENTER button. • When the OPTIONS menu is displayed, the drive list will not be displayed. 3. Display the [SHARED FOLDER SETTING] screen. Press the ▼ button to select the (SHARED FOLDER
NEC NP-PA521U | User's Manual - Page 86
6. Exit the setting. Press the ▼ button to select [OK] and press the ENTER button. This will close the [SHARED FOLDER] screen. • If an error message appear, your settings are not correct. Try again. 4. Using the Viewer 74
NEC NP-PA521U | User's Manual - Page 87
Disconnecting the shared folder from the projector 4. Using the Viewer • Disable the number of a shared folder you wish to disconnect Press the ▼ button to select [ENABLE] and press the ENTER button to clear it. NOTE: • When a PowerPoint file or PDF file is displayed, do not disconnect your LAN
NEC NP-PA521U | User's Manual - Page 88
❺ Projecting data from media server 4. Using the Viewer Media server LAN Media server Wireless LAN Projector Media server Preparation For projector: Connect the projector to the network. For computer: Prepare image files or movie files to be projected, and set up "Media Sharing" in Windows
NEC NP-PA521U | User's Manual - Page 89
3. Select "Share my media" check box, and then select OK. 4. Using the Viewer A list of accessible devices will be displayed. 4. Select "PA600 Series" and then "Allow". A check mark will be added to the "PA600 Series" icon. • The "PA600 Series" is a projector name specified in [NETWORK SETTINGS].
NEC NP-PA521U | User's Manual - Page 90
Setting up "Media Sharing" in Windows Media Player 12 1. Start Windows Media Player 12. 4. Using the Viewer 2. Select "Stream", and then select "Automatically allow devices to play my media". The "Allow All Media Devices" windows will be displayed. 3. Select "Automatically allow all computers and
NEC NP-PA521U | User's Manual - Page 91
Connecting the projector to the media server Press the VIEWER button on the remote control. The VIEWER will start. 4. Using the Viewer • Another way to start the VIEWER is to press the SOURCE button a few times on the projector cabinet. (→ page 16) • This will start searching for a computer with "
NEC NP-PA521U | User's Manual - Page 92
Disconnecting the projector from the media server 1. Display the OPTIONS menu. 4. Using the Viewer Press the ▼ button to select the [OPTIONS] icon and select the ENTER button. 2. Display the MEDIA SERVER setting screen. Press the ▼ button to select the MEDIA SERVER icon and press the ENTER button
NEC NP-PA521U | User's Manual - Page 93
vary in size or width, causing layout corruption Some characters or fonts may not be displayed. • Some functions included in font are not supported. Example: There are some restrictions on animation, selection, or hyperlink. • It may take longer time to feed pages compared with a computer • In some
NEC NP-PA521U | User's Manual - Page 94
5. Using On-Screen Menu  Using the Menus NOTE: The on-screen menu may not be displayed correctly while interlaced motion video image is projected. 1. Press the MENU button on the remote control or the projector cabinet to display the menu. NOTE: The commands such as ENTER, EXIT in the bottom show
NEC NP-PA521U | User's Manual - Page 95
2 Menu Elements Tab Available buttons Source Highlight 5. Using On-Screen Menu Slide bar Solid triangle Menu mode Radio button Wireless symbol ECO mode symbol High Altitude symbol Thermometer symbol Off Timer remaining time Key Lock symbol Menu windows or dialog boxes typically have the
NEC NP-PA521U | User's Manual - Page 96
5. Using On-Screen Menu 3 List of Menu Items Some menu items are not available depending on the input source. Menu Item SOURCE COMPUTER1 COMPUTER2 COMPUTER3(BNC) HDMI DisplayPort VIDEO S-VIDEO VIEWER NETWORK ENTRY LIST TEST PATTERN MODE Default STANDARD PRESET * GENERAL REFERENCE *
NEC NP-PA521U | User's Manual - Page 97
ON OFF, ON ON OFF, ON OFF OFF, ON AUTO 45 SEC MANUAL, AUTO 5 SEC, AUTO 15 SEC, AUTO 45 SEC BLUE BLUE, BLACK LAN, WIRELESS LAN, WPS, NETWORK INFORMATION, PROJECTOR NAME, DOMAIN, ALERT MAIL, NETWORK SERVICE OFF OFF, ON OFF OFF, ON 38400bps 4800bps, 9600bps, 19200bps, 38400bps, 115200bps
NEC NP-PA521U | User's Manual - Page 98
SETUP INFO. RESET OPTIONS(2) STANDBY MODE DIRECT POWER ON AUTO POWER ON(COMP1/3) AUTO POWER OFF DEFAULT SOURCE SELECT LAMP LIFE REMAINING USAGE TIME LAMP HOURS USED FILTER HOURS USED TOTAL CARBON SAVINGS INPUT TERMINAL RESOLUTION HORIZONTAL FREQUENCY VERTICAL FREQUENCY SOURCE(1) SYNC
NEC NP-PA521U | User's Manual - Page 99
5. Using On-Screen Menu 4 Menu Descriptions & Functions [SOURCE] COMPUTER 1, 2, and 3 Selects the computer connected to your COMPUTER 1, 2, or COMPUTER 3 input connector signal. NOTE: When the component input signal is connected to the COMPUTER IN, COMPUTER 2 IN, or COMPUTER 3 IN connector, select [
NEC NP-PA521U | User's Manual - Page 100
5. Using On-Screen Menu Using the Entry List When any source adjustments are made, the adjustments are automatically registered in the Entry List.The (adjustment values of) registered signals can be loaded from the Entry List whenever necessary. However, only up to 100 patterns can be registered in
NEC NP-PA521U | User's Manual - Page 101
Entering the currently projected signal into the Entry List [STORE] 1. Press the  or  button to select any number. 5. Using On-Screen Menu 2. Press the  or  button to select [STORE] and press the ENTER button. Calling up a signal from the Entry List [LOAD] Press the  or  button to select a
NEC NP-PA521U | User's Manual - Page 102
Cutting a signal from the Entry List [CUT] 5. Using On-Screen Menu 1. Press the  or  button to select a signal you wish to delete. 2. Press the or  button to select [CUT] and press the ENTER button. The signal will be deleted from the Entry List and the deleted signal will be displayed on the
NEC NP-PA521U | User's Manual - Page 103
5. Using On-Screen Menu 5 Menu Descriptions & Functions [ADJUST] [PICTURE] [MODE] This function allows you to determine how to save settings for [DETAIL SETTINGS] of [PRESET] for each input. STANDARD Saves settings for each item of [PRESET] (Preset 1 through 7) PROFESSIONAL Saves all the settings
NEC NP-PA521U | User's Manual - Page 104
5. Using On-Screen Menu [GENERAL] Storing Your Customized Settings [REFERENCE] This function allows you to store your customized settings in [PRESET 1] to [PRESET 7]. First, select a base preset mode from [REFERENCE], then set [GAMMA CORRECTION] and [COLOR TEMPERATURE]. HIGH-BRIGHT Recommended for
NEC NP-PA521U | User's Manual - Page 105
[COLOR CORRECTION] Corrects the color for all signals. Adjusts the tone for the colors red, green, blue, yellow, magenta and cyan. 5. Using On-Screen Menu RED Adjusts the color in red areas, centered around the red. This can be used to adjust to a yellow- or magenta-tinged red. GREEN Adjusts the
NEC NP-PA521U | User's Manual - Page 106
[IMAGE OPTIONS] 5. Using On-Screen Menu Adjusting Clock and Phase [CLOCK/PHASE] This allows you to manually adjust CLOCK and PHASE. CLOCK Use this item to fine tune the computer image or to remove any vertical banding that might appear. This function
NEC NP-PA521U | User's Manual - Page 107
Adjusting Horizontal/Vertical Position [HORIZONTAL/VERTICAL] Adjusts the image location horizontally and vertically. 5. Using On-Screen Menu - An image can be distorted during the adjustment of [CLOCK] and [PHASE]. This is not malfunction. - The adjustments for [CLOCK], [PHASE], [HORIZONTAL], and
NEC NP-PA521U | User's Manual - Page 108
5. Using On-Screen Menu Selecting the Aspect Ratio [ASPECT RATIO] Use this function to select the screen's vertical:horizontal aspect ratio. Select the screen type (4:3 screen, 16:9 screen or 16:10 screen) at the screen setting before setting the aspect ratio. (→ page 104) The projector
NEC NP-PA521U | User's Manual - Page 109
LETTER BOX 5. Using On-Screen Menu The image of a letterbox signal (16:9) is stretched equally in the horizontal and vertical directions to fit the screen. WIDE SCREEN The image of a squeeze signal(16:9) is stretched left and right in 16:9. ZOOM The image of a squeeze signal (16:9) is stretched
NEC NP-PA521U | User's Manual - Page 110
[VIDEO] 5. Using On-Screen Menu Using Noise Reduction [NOISE REDUCTION] This function is used to reduce video noise. RANDOM NR Reduces flickering random noise in an image. MOSQUITO NR Reduces mosquito noise that appears around the edges of an image during DVD playback. BLOCK NR Reduces block
NEC NP-PA521U | User's Manual - Page 111
5. Using On-Screen Menu [VIDEO LEVEL] This function selects video signal level when the projector's HDMI and DisplayPort input connectors and an external device are connected. AUTO The video level is switched automatically based on the information from the device outputting the signal. Depending on
NEC NP-PA521U | User's Manual - Page 112
5. Using On-Screen Menu 6 Menu Descriptions & Functions [SETUP] [BASIC] Correcting Vertical Keystone Distortion Manually [KEYSTONE] You can correct vertical distortion manually. (→ page 22) TIP: When this option is highlighted, pressing the ENTER button will display its slide bar for adjustment.
NEC NP-PA521U | User's Manual - Page 113
3 MINUTES] message will be displayed on the bottom of the screen. Selecting Menu Language [LANGUAGE] You can choose one of 27 languages for on-screen instructions. NOTE: Your setting will not be affected even when [RESET] is done from the menu. 101
NEC NP-PA521U | User's Manual - Page 114
[MENU] 5. Using On-Screen Menu Selecting Menu Color [COLOR SELECT] You can choose between two options for menu color: COLOR and MONOCHROME. Turning On / Off Source Display [SOURCE DISPLAY] This option turns on or off input name display such as COMPUTER 1, COMPUTER2, COMPUTER3, HDMI, DisplayPort,
NEC NP-PA521U | User's Manual - Page 115
option allows you to select how long the projector waits after the last touch of a button to turn off the menu. The preset choices are [MANUAL], [AUTO 5 SEC], [AUTO 15 SEC], and [AUTO 45 SEC]. The [AUTO 45 SEC] is the factory preset. Selecting a Color or Logo for Background [BACKGROUND] Use
NEC NP-PA521U | User's Manual - Page 116
DESKTOP FRONT DESKTOP REAR 5. Using On-Screen Menu CEILING REAR CEILING FRONT Selecting Aspect Ratio and Position for Screen [SCREEN] Screen type Sets the aspect ratio of the projection screen. 4:3 screen For a screen with a 4:3 aspect ratio 16:9 screen For a screen with a 16:9 aspect ratio
NEC NP-PA521U | User's Manual - Page 117
5. Using On-Screen Menu ON: Turns on this function to make the screen darker. The [BRIGHTNESS] and the [CONTRAST] can be adjusted. CONTRAST Adjusts the bright part of the picture. BRIGHTNESS Adjusts the dark part of the picture. Adjusting 1. Prepare black and white images so that the images can be
NEC NP-PA521U | User's Manual - Page 118
] is done from the menu. Selecting Communication Speed [COMMUNICATION SPEED] This feature sets the baud rate of the PC Control port (D-Sub 9P). It supports data rates from 4800 to 115200 bps. The default is 38400 bps. Select the appropriate baud rate for your equipment to be connected (depending on
NEC NP-PA521U | User's Manual - Page 119
5. Using On-Screen Menu NOTE: • When [ON] is selected for [CONTROL ID], the projector cannot be operated by using the remote control that does not support the CONTROL ID function. (In this case the buttons on the projector cabinet can be used.) • Your setting will not be affected even when [RESET]
NEC NP-PA521U | User's Manual - Page 120
Using On-Screen Menu Setting Auto Adjust [AUTO ADJUST] This feature sets the Auto Adjust mode so that the computer signal can be automatically or manually adjusted for noise and stability. You can automatically make adjustment in two ways: [NORMAL] and [FINE]. OFF The computer signal will not be
NEC NP-PA521U | User's Manual - Page 121
5. Using On-Screen Menu NOTE: • When [HIGH ALTITUDE] is selected for [FAN MODE], a symbol icon will be displayed at the bottom of the menu. • It is recommended that you select High speed mode if you use the projector non-stop for consecutive days. • Set [FAN MODE] to [HIGH ALTITUDE] when using the
NEC NP-PA521U | User's Manual - Page 122
[OPTIONS(2)] 5. Using On-Screen Menu Selecting Power-saving in [STANDBY MODE] The projector has three standby modes: [NORMAL], [POWER-SAVING] and [NETWORK STANDBY]. The POWER-SAVING mode is the mode that allows you to put the projector in the power-saving condition which consumes less power than
NEC NP-PA521U | User's Manual - Page 123
5. Using On-Screen Menu Turning On the Projector By Applying Computer Signal [AUTO POWER ON(COMP1/3)] When the projector is in Standby mode, applying a computer signal from a computer connected to the COMPUTER1 IN or COMPUTER3 IN input will power on the projector and simultaneously project the
NEC NP-PA521U | User's Manual - Page 124
5. Using On-Screen Menu 7 Menu Descriptions & Functions [INFO.] Displays the status of the current signal and lamp usage. This item has nine pages. The information included is as follows: TIP: Pressing the HELP button on the remote control will show the [INFO.] menu items. [USAGE TIME] [LAMP LIFE
NEC NP-PA521U | User's Manual - Page 125
[SOURCE(1)] 5. Using On-Screen Menu INPUT TERMINAL HORIZONTAL FREQUENCY SYNC TYPE SCAN TYPE ENTRY NO. [SOURCE(2)] RESOLUTION VERTICAL FREQUENCY SYNC POLARITY SOURCE NAME SIGNAL TYPE BIT DEPTH LINK RATE [WIRED LAN] VIDEO TYPE VIDEO LEVEL LINK LANE IP ADDRESS GATEWAY SUBNET MASK MAC ADDRESS 113
NEC NP-PA521U | User's Manual - Page 126
[WIRELESS LAN(1)] 5. Using On-Screen Menu IP ADDRESS GATEWAY [WIRELESS LAN(2)] SUBNET MASK MAC ADDRESS SSID WEP/WPA SIGNAL LEVEL [VERSION(1)] NETWORK TYPE CHANNEL FIRMWARE FIRMWARE2 DATA SUB-CPU 114
NEC NP-PA521U | User's Manual - Page 127
[VERSION(2)] 5. Using On-Screen Menu FIRMWARE3 [OTHERS] PROJECTOR NAME SERIAL NUMBER CONTROL ID (when [CONTROL ID] is set) MODEL NO. LAN UNIT TYPE 115
NEC NP-PA521U | User's Manual - Page 128
5. Using On-Screen Menu 8 Menu Descriptions & Functions [RESET] Returning to Factory Default [RESET] The RESET feature allows you to change adjustments and settings to the factory preset for a (all) source (s) except the following: [CURRENT SIGNAL] Resets the adjustments for the current signal to
NEC NP-PA521U | User's Manual - Page 129
5. Using On-Screen Menu Clearing the Filter Usage Hours [CLEAR FILTER HOURS] Resets the filter usage back to zero. Selecting this option displays submenu for a confirmation. Select [YES] and press the ENTER button. The [OFF] item is selected for [FILTER MESSAGE] at the time of shipment. When [OFF]
NEC NP-PA521U | User's Manual - Page 130
5. Using On-Screen Menu ❾ Application Menu When [NETWORK] is selected from the [SOURCE] menu, the application menu [APPLICATION MENU] will be displayed. The application menu allows you to set up the User Supportware, Network Settings (NETWORK SETTINGS) and Tools (TOOLS). The User Supportware is
NEC NP-PA521U | User's Manual - Page 131
5. Using On-Screen Menu NETWORK PROJECTOR This shows information for projector name, resolution, and network (wired/wireless) which are required to use Network Projector. Use this information to set up for your computer. REMOTE DESKTOP CONNECTION This allows you to set up for computer name entry and
NEC NP-PA521U | User's Manual - Page 132
NETWORK SETTINGS 5. Using On-Screen Menu Important: • Consult with your network administrator about these settings. • When using a wired LAN connection, connect a LAN cable (Ethernet cable) to the LAN port (RJ-45) of the projector. (→ page 150) TIP: The network settings you make will not be
NEC NP-PA521U | User's Manual - Page 133
WIRED LAN or WIRELESS LAN (ADVANCED menu only) 5. Using On-Screen Menu * To use the wireless LAN functions, connect a separately sold wireless LAN unit to the projector. (→ page 151) PROFILES • Up to two settings for the LAN port or USB wireless LAN unit - can be stored in memory of the
NEC NP-PA521U | User's Manual - Page 134
5. Using On-Screen Menu DHCP IP ADDRESS SUBNET MASK GATEWAY WNS CONFIGURATION AUTO DNS DNS CONFIGURATION ADVANCED* RECONNECT • When selecting [WPS], the network will be connected by using settings stored automatically with the WPS function. Selecting [WPS] will allow the projector to access the
NEC NP-PA521U | User's Manual - Page 135
SITE SURVEY SECURITY SSID NETWORK TYPE CHANNEL 5. Using On-Screen Menu Displays a list of available SSIDs for wireless LAN on site. Select - an SSID which you can access. To select an SSID, highlight [SSID] and use the  to select [OK] and press the ENTER button. Wireless access point Ad Hoc
NEC NP-PA521U | User's Manual - Page 136
5. Using On-Screen Menu When [WEP(64bit)] or [WEP(128bit)] is selected for [SECURITY TYPE] KEY SELECT KEY1, KEY2, KEY3, KEY4 Selects one WEP key from the four keys below. Enter a WEP key. • Maximum number of characters Option Alphanumeric (ASCII) WEP 64bit 5 WEP 128bit 13 Hexadecimal (HEX)
NEC NP-PA521U | User's Manual - Page 137
device. After completing saving the file, remove the USB memory device from the computer. Important: • The file formats of digital certificate that are supported by the projector are DER and PKCS#12 only. • The projector cannot handle any digital certificate whose file size exceeds 8 KB. • CRL
NEC NP-PA521U | User's Manual - Page 138
4. Select [SITE SURVEY] and press the ENTER button. 5. Using On-Screen Menu The "SSID" list will be displayed. 5. Select a connecting SSID, and then select [OK]. Finally press the ENTER button. • Select the SSID for which WPA-PSK or WPA2-PSK is set. • Select [INFRASTRUCTURE ( )] for [NETWORK TYPE
NEC NP-PA521U | User's Manual - Page 139
11.Select the [AUTHENTICATION] tab. 5. Using On-Screen Menu The [AUTHENTICATION] page will be displayed. Select either [EAP-TLS] or [PEAP-MSCHAPv2] for [EAP TYPE]. The setting items vary depending on the EAP type. See the table below. EAP Type Setting Item Note EAP-TLS User Name 1 character
NEC NP-PA521U | User's Manual - Page 140
Menu A list of files (thumbnail screen) will be displayed. • For operating the thumbnail screen, see "4. Using the Viewer" in the "User's Manual" (PDF). • To return to the [AUTHENTICATION] page, press the EXIT button. NOTE: Installing a digital certificate You can install each digital certificate
NEC NP-PA521U | User's Manual - Page 141
5. Using On-Screen Menu 17.On the thumbnail screen, select a digital certificate (DER format file) saved in your USB memory device and press the ENTER button. • Select your root CA certificate here. The selected digital certificate will be installed on the projector. 18.After completing required
NEC NP-PA521U | User's Manual - Page 142
the ENTER button. The drive list screen will be displayed. • For operating the thumbnail screen, see "4. Using the Viewer" in the "User's Manual" (PDF). • To return to the [AUTHENTICATION] page, press the EXIT button. NOTE: Installing a digital certificate You can install each digital certificate
NEC NP-PA521U | User's Manual - Page 143
5. Using On-Screen Menu 18.After completing required settings, select [OK] and press the ENTER button. The [WIRELESS] page will be returned. 19.Select [RECONNECT] and press the ENTER button. 20.Select [OK] and press the ENTER button. This will complete setting [PEAP-MSCHAPv2] for [EAP TYPE] in [WPA-
NEC NP-PA521U | User's Manual - Page 144
5. Using On-Screen Menu WPS When the wireless LAN access point connected to the projector supports WPS (Wi-Fi Protected Setup TM), you can use PIN method or push button method to set up the wireless LAN for the projector. PIN
NEC NP-PA521U | User's Manual - Page 145
PROJECTOR NAME (ADVANCED menu only) PROJECTOR NAME Set a unique projector name. DOMAIN (ADVANCED menu only) Set a host name and domain name of the projector. HOST NAME DOMAIN NAME Set a host name of the projector. Set a domain name of the projector. 5. Using On-Screen Menu Up to 16 alphanumeric
NEC NP-PA521U | User's Manual - Page 146
ALERT MAIL (ADVANCED menu only) 5. Using On-Screen Menu ALERT MAIL HOST NAME DOMAIN NAME SENDER'S ADDRESS SMTP SERVER NAME RECIPIENT'S ADDRESS 1, 2, 3 TEST MAIL This option will notify your computer of lamp replace time or error - messages via e-mail when using wireless or wired LAN. Placing a
NEC NP-PA521U | User's Manual - Page 147
NETWORK SERVICE (ADVANCED menu only) 5. Using On-Screen Menu HTTP SERVER PJLink AMX is established by Japan Business Machine and Information System Industries Association (JBMIA) in 2005. The projector supports all the commands of PJLink Class 1. • Setting of PJLink will not be affected even when
NEC NP-PA521U | User's Manual - Page 148
TOOLS 5. Using On-Screen Menu ADMINISTRATOR MODE This allows you to select MENU MODE, save settings, and set a password for the administrator mode. MENU MODE NOT SAVE SETTING VALUES NEW PASSWORD/ CONFIRM PASSWORD Select either [BASIC] or [ADVANCED] menu. (→ page 84) Placing a check mark will not
NEC NP-PA521U | User's Manual - Page 149
PROGRAM TIMER 5. Using On-Screen Menu This option turns on/off the projector and changes video signals, and selects ECO mode automatically at a specified time. NOTE: • Before using [PROGRAM TIMER], make sure that the [DATE AND TIME] feature is set. (→ page 140) • Make sure that the projector is in
NEC NP-PA521U | User's Manual - Page 150
projector is turned on by using the program timer and if you want to turn off the projector, set the off-time or do it manually so as not to leave the projector on for a long period of time. 138
NEC NP-PA521U | User's Manual - Page 151
Activating the program timer 5. Using On-Screen Menu 1. Select [ENABLE] on the [PROGRAM TIMER] screen and press the ENTER button. The [ENABLE] will be activated. 2. Select [OK] and press the ENTER button. The [PROGRAM TIMER] screen will be changed to the [TOOL] screen. NOTE: • Clearing [ENABLE]
NEC NP-PA521U | User's Manual - Page 152
DATE ANDTIME 5. Using On-Screen Menu You can set the current time, month, date, and year. NOTE: The projector has a built-in clock. The clock will keep working for about 2 weeks after the main power is turned off. If the main power is off for 2 weeks or more, the built-in clock will cease. If the
NEC NP-PA521U | User's Manual - Page 153
attachment is on. For the types of lenses that can be mounted and instructions on removing them, see the lense's operating instructions. - Other types of lenses cannot be mounted on this projector. Mounting the way in, keeping the positioning slit at the same angle. Guiding notch 141 Yellow mark
NEC NP-PA521U | User's Manual - Page 154
4. Turn the lens clockwise. Turn until a click is heard. The lens is now fastened onto the projector. TIP: Mounting the lens theft prevention screw Fasten the lens theft prevention screw included with the projector to the bottom of the projector so that the lens cannot be removed easily. Removing
NEC NP-PA521U | User's Manual - Page 155
6. Installation and Connections  Making Connections The projector can be connected to a computer using the computer cable (included), a BNC cable (5-core type) (commercially available), HDMI cable (commercially available) or DisplayPort cable (commercially available). Analog RGB signal connection •
NEC NP-PA521U | User's Manual - Page 156
. • If the computer has a mini-jack type audio output connector, we recommend connecting the audio cable to that connector. • This projector does not support NEC video unit (model ISS-6020) video decoded outputs. • When a video deck is connected via a scan converter, etc., the display may not be
NEC NP-PA521U | User's Manual - Page 157
6. Installation and Connections Cautions when connecting an HDMI cable • Use a certified High Speed HDMI® Cable or High Speed HDMI® Cable with Ethernet. Cautions when connecting a DisplayPort cable • Use a certified DisplayPort cable. • Depending on the computer, some time may be required until the
NEC NP-PA521U | User's Manual - Page 158
Connecting an External Monitor 6. Installation and Connections HDMI OUT AUDIO OUT HDMI cable (not supplied) Stereo mini-plug audio cable (not supplied) HDMI IN AUDIO IN Computer cable (VGA) (supplied) You can connect a separate, external monitor to your projector to simultaneously view on a
NEC NP-PA521U | User's Manual - Page 159
on the projector. NOTE: The AUDIO IN L and R jacks (RCA) are shared between the Video and S-Video inputs. NOTE: Refer to your VCR owner's manual for more information about your equipment's video output requirements. NOTE: • An image may not be displayed correctly when a Video or S-Video source is
NEC NP-PA521U | User's Manual - Page 160
Connecting Component Input COMPUTER IN 6. Installation and Connections AUDIO IN AUDIO IN 15-pin - to - RCA (female) × 3 cable adapter (ADP-CV1E) Component video RCA × 3 cable (not supplied) DVD player RCA (female) - to - BNC (male) connector (not supplied) Stereo mini plug - to - RCA audio cable
NEC NP-PA521U | User's Manual - Page 161
type PC to the HDMI IN connector of your projector. NOTE: The HDMI IN connector supports Plug & Play (DDC2B). HDMI 1 IN HDMI 2 IN HDMI cable (not supplied) dark areas. For more information on settings, refer to the instruction manual of the audio video equipment to be connected. • When connecting
NEC NP-PA521U | User's Manual - Page 162
6. Installation and Connections Connecting to a Wired LAN The projector comes standard with a LAN port (RJ-45) which provides a LAN connection using a LAN cable. To use a LAN connection, you are required to set the LAN on the projector menu. Select [APPLICATION MENU] → [NETWORK SETTINGS] → [WIRED
NEC NP-PA521U | User's Manual - Page 163
6. Installation and Connections Connecting to a Wireless LAN (sold separately) The separately sold wireless LAN unit allows you to use a wireless LAN environment. When using the projector in a wireless LAN environment, the IP address and other settings must be made on the projector. Important: • If
NEC NP-PA521U | User's Manual - Page 164
6. Installation and Connections 1. Press the button to set the projector to the standby mode, then disconnect the power cord. Wait for the projector to fully cool off. Filter cover 2. Remove the filter cover. Pressing the buttons on the left and right sides of the filter cover upwards, pull the
NEC NP-PA521U | User's Manual - Page 165
6. Installation and Connections WIRELESS To remove the wireless LAN unit 1. Remove the filter unit following steps 1 to 3 above. 2. Remove the wireless LAN unit. WIRELESS If the wireless LAN unit is hard to remove, place a cloth, etc., over needlenose pliers to grasp the wireless LAN unit and
NEC NP-PA521U | User's Manual - Page 166
Example of wireless LAN connection (Network Type → Infrastructure) (→ page 123) USB Wireless LAN Unit 6. Installation and Connections PC with wireless LAN card inserted PC with built-in wireless LAN function Wireless access point Wired LAN Example of wireless LAN connection (Network Type → Ad
NEC NP-PA521U | User's Manual - Page 167
intake vents. Doing so will cause build-up heat inside the projector. • When using the projector on its left side, attach a stand supporting the projector. • Lock the lens shift after completing lens shift adjustment. Specifications of stand for projecting portrait images For designing a stand for
NEC NP-PA521U | User's Manual - Page 168
Reference drawing [Side View] [Front View] 4-M4 screw hole 6. Installation and Connections [Bottom View] 310 mm or longer Filter cover Rear foot Remove tilt foot 130 or longer Filter cover (open) Horizontal adjuster Locking Lens Shift 1. Pull and remove the lever cover. 2. Loosen the screw. •
NEC NP-PA521U | User's Manual - Page 169
3. Move the lever upward until it stops and then secure the screw. • While holding the lever upward, tighten the screw. • To adjust the lens shift again, loosen the screw and do this. 6. Installation and Connections 4. Put the lever cover back. 157
NEC NP-PA521U | User's Manual - Page 170
7. Maintenance This section describes the simple maintenance procedures you should follow to clean the filters, the lens, the cabinet, and to replace the lamp and the filters.  Cleaning the Filters The air-filter sponge keeps dust and dirt from getting inside the projector and should be frequently
NEC NP-PA521U | User's Manual - Page 171
(2)Push the left edges of the filters and remove the two hard honeycomb filters. - The filters cannot be removed by pressing the left and right edges. 4. Use a vacuum cleaner to vacuum all the dust inside. Get rid of dust in the accordion filter NOTE: • Whenever you vacuum the filter, use the soft
NEC NP-PA521U | User's Manual - Page 172
8. Put the filter cover back to the projector cabinet. Insert the 4 catches on the top of the filter cover into the grooves in the projector, then press the left and right buttons to close. • Push the filter cover until it clicks into place. 9. Clear the filter usage hours. Plug the power cord into
NEC NP-PA521U | User's Manual - Page 173
7. Maintenance 2 Cleaning the Lens • Turn off the projector before cleaning. • The projector has a plastic lens. Use a commercially available plastic lens cleaner. • Do not scratch or mar the lens surface as a plastic lens is easily scratched. • Never use alcohol or glass lens cleaner as doing so
NEC NP-PA521U | User's Manual - Page 174
7. Maintenance 4 Replacing the Lamp and the Filters When the lamp reaches the end of its life, the LAMP indicator in the cabinet will blink red and the message "THE LAMP HAS REACHED THE END OF ITS USABLE LIFE. PLEASE REPLACE THE LAMP AND FILTER. USE THE SPECIFIED LAMP FOR SAFETY AND PERFORMANCE."
NEC NP-PA521U | User's Manual - Page 175
circumvent this interlock. (2)Remove the lamp housing by holding it. CAUTION: Make sure that the lamp housing is cool enough to before removing it. Interlock Guide hole 163
NEC NP-PA521U | User's Manual - Page 176
7. Maintenance 3. Install a new lamp housing. (1)Insert a new lamp housing until the lamp housing is plugged into the socket. (2)Position so that the guide hole in the bottom right of the lamp house is over the protrusion on the projector then press all the way in. (3)Secure it in
NEC NP-PA521U | User's Manual - Page 177
7. Maintenance To replace the filters: Four filters are packaged with the replacement lamp. Honeycomb filter (coarse mesh): Large and small sizes (attached to the outside of the filter unit) Accordion filter (fine mesh): Large and small sizes (attached to the inside of the filter unit) NOTE: •
NEC NP-PA521U | User's Manual - Page 178
7. Maintenance (2)Push the left edges of the filters and remove the two hard honeycomb filters (large and small). • The filters cannot be removed by pressing the left and right edges. 4. Remove dust from the filter unit and the filter cover. Clean both outside and inside. 5. Attach four new filters
NEC NP-PA521U | User's Manual - Page 179
8. User Supportware  Installing Software Program Installation for Windows software The software programs except Image Express Utility 2 for Mac support Windows 7, Windows Vista, and Windows XP. NOTE: • To install or uninstall each software program, the Windows user account must have "Administrator"
NEC NP-PA521U | User's Manual - Page 180
program and click it. 4 Click "Uninstall/Change" or "Uninstall". • When the "User Account Control" windows is displayed, click "Continue". Follow the instructions on the screens to complete the uninstallation. • For Windows XP 1 Click "Start" and then "Control Panel". The Control Panel window will
NEC NP-PA521U | User's Manual - Page 181
Installation for Macintosh software Image Express Utility 2 for Mac supports Mac OS X. 1 Insert the accompanying NEC Projector CD-ROM into your CD-ROM drive. The menu window will be displayed. 2 Double-click the CD-ROM
NEC NP-PA521U | User's Manual - Page 182
can be used also with a serial connection. Connect the projector to a LAN. Connect the projector to the LAN by following the instructions in "Connecting to a Wired LAN" (→ page 150), "Connecting to a Wireless LAN (sold separately)" (→ page 151) and "9 Application Menus - NETWORK SETTINGS" (→ page
NEC NP-PA521U | User's Manual - Page 183
Start Virtual Remote Tool Start using the shortcut icon • Double-click the shortcut icon on the Windows Desktop. 8. User Supportware Start from the Start menu • Click [Start] → [All Programs] or [Programs] → [NEC Projector User Supportware] → [Virtual Remote Tool] → [Virtual Remote Tool]. When
NEC NP-PA521U | User's Manual - Page 184
Exiting Virtual Remote Tool 1 Click the Virtual Remote Tool icon The pop-up menu will be displayed. on the Taskbar. 8. User Supportware 2 Click "Exit". The Virtual Remote Tool will be closed. Viewing the help file of Virtual Remote Tool • Displaying the help file using the taskbar 1 Click the
NEC NP-PA521U | User's Manual - Page 185
Correction Tool in Image Express Utility Lite)". Connect the projector to a LAN. Connect the projector to the LAN by following the instructions in "Connecting to a Wired LAN" (→ page 150), "Connecting to a Wireless LAN (sold separately)" (→ page 151) and "9 Application Menus - NETWORK SETTINGS
NEC NP-PA521U | User's Manual - Page 186
8. User Supportware When connecting with the projector is establised, you can operate the control window to control the projector. NOTE: • When [POWER-SAVING] or [NETWORK STANDBY] is selected for [STANDBY MODE] from the menu, the projector that is turned off will not be displayed in the select
NEC NP-PA521U | User's Manual - Page 187
8. User Supportware  Projecting an Image from an Angle (Geometric Correction Tool in Image Express Utility Lite) The Geometric Correction Tool (GCT) function allows you to correct distortion of images projected even from an angle. What you can do with GCT • The GCT feature includes the following
NEC NP-PA521U | User's Manual - Page 188
3. Use the mouse to click the [ • ] mark of which corner you wish to move. The currently selected [ • ] mark will turn red. 8. User Supportware (In the above example, Windows screens are omitted for clarification.) 4. Drag the selected [ • ] mark to the point you wish to correct and drop it. •
NEC NP-PA521U | User's Manual - Page 189
is off while Desktop Control Utility 1.0 is running. Connecting the projector to a LAN Connect the projector to the LAN by following the instructions in "Connecting to a Wired LAN" (→ page 150), "Connecting to a Wireless LAN" (→ page 151) and "9 Application Menus - NETWORK SETTINGS" (→ page 120) 177
NEC NP-PA521U | User's Manual - Page 190
Using the projector to operate your computer's desktop screen 8. User Supportware IMPORTANT: • In case of Windows 7/Windows Vista, disable the user account control before using Desktop Control Utility 1.0. Windows Vista has "User Account Control" function to protect the computer. The user account
NEC NP-PA521U | User's Manual - Page 191
starting password, reinstall the Desktop Control Utility 1.0. A screen like the one below is displayed when the software is started on a PC installed with Windows XP Service Pack 2 (SP2) (or later). Click "Unblock" if this is displayed. 179
NEC NP-PA521U | User's Manual - Page 192
3 Input the starting password of Desktop Control Utility 1.0, and click [OK]. The "Current password" window will be displayed. 8. User Supportware NOTE: The character string displayed in the password field varies each time Desktop Control Utility 1.0 is started. 4 Write down the character string
NEC NP-PA521U | User's Manual - Page 193
• Operating the projector (connecting computer) 1 Connect a USB mouse that is commercially available to the projector. USB 8. User Supportware 2 Turn on the power to the projector. Set the LAN setting of the projector in advance. 3 Press the SOURCE button on the projector unit. The Source list
NEC NP-PA521U | User's Manual - Page 194
5 Click [DESKTOP CONTROL UTILITY]. The "DESKTOP CONTROL UTILITY menu" screen will be displayed. 8. User Supportware 6 Click "ENTRY". A password input screen will be displayed. 7 Input the password you have written down in step 4 of "Operation on computer". • Click the [BS] button on the right side
NEC NP-PA521U | User's Manual - Page 195
8. User Supportware 10 Click the computer at the connection destination and then [OK]. The desktop screen of the computer at the connection destination will be displayed. • Operating the projector (manipulating desktop screen) The displayed desktop screen can be manipulated by using the USB mouse
NEC NP-PA521U | User's Manual - Page 196
8. User Supportware (cut-off icon Disconnects communication with the computer. (Shift icon When the highlight is moved to this icon and the ENTER button is pressed, shift lock status is set. The shift lock is canceled if the highlight is moved to this icon and the ENTER
NEC NP-PA521U | User's Manual - Page 197
• Operating the projector (exiting Desktop Control Utility 1.0) 8. User Supportware 1 Click the projector icon [ ] on the taskbar while the desktop screen is displayed. 2 Click [Exit]. Desktop Control Utility 1.0 will be terminated. 3 Press the EXIT button on the projector unit or on the remote
NEC NP-PA521U | User's Manual - Page 198
Pro 4 can be used with a serial connection. Connect the projector to a LAN. Connect the projector to the LAN by following the instructions in "Connecting to a Wired LAN" (→ page 150), "Connecting to a Wireless LAN (sold separately)" (→ page 151) and "9 Application Menus - NETWORK SETTINGS" (→ page
NEC NP-PA521U | User's Manual - Page 199
on this projector. Refer to the information on this page and use a lens suited for the installation environment (screen size and throw distance). For instructions on mounting the lens, see page 141. Lens types and throw distance PA722X/PA721X/PA622X/PA621X Screen size 30" 40" 60" 80" 100" 120
NEC NP-PA521U | User's Manual - Page 200
9. Appendix PA672W/PA671W/PA572W/PA571W Screen size 30" 40" 60" 80" 100" 120" 150" 200" NP11FL 0.7 1.0 1.4 1.7 2.1 2.6 240" 300" 400" 500" NP12ZL 0.7 - 1.0 1.0 - 1.3 1.5 - 2.0 2.0 - 2.6 2.5 - 3.3 3.1 - 4.0 3.8 - 5.0 5.1 - 6.7 6.2 - 8.0 7.7 - 10.1 10.3 - 13.4 12.9 - 16.8 Lens model name NP13ZL
NEC NP-PA521U | User's Manual - Page 201
Projection range for the different lenses NP11FL PA622U/PA621U/PA522U/PA521U: 0.7-2.6 m PA672W/PA671W/PA572W/PA571W: 0.7-2.6 m PA722X/PA721X/PA622X/PA621X: 0.6-2.5 m NP30ZL PA622U/PA621U/PA522U/PA521U: 1.0-11.3 m PA672W/PA671W/PA572W/PA571W: 1.0-11.3 m PA722X/PA721X/PA622X/PA621X: 1.0-10.9 m 40
NEC NP-PA521U | User's Manual - Page 202
Tables of screen sizes and dimensions 9. Appendix PA722X/PA721X/PA622X/PA621X Screen height 4:3 screen size (diagonal) Screen width Size (inches) 30 40 60 80 100 120 150 200 240 300 400 500 Screen width (inches) 24 32 48 64 80 96 120 160 192 240 320 400 (cm) 61.0 81.3 121.9 162.6 203.2 243
NEC NP-PA521U | User's Manual - Page 203
9. Appendix Lens shifting range This projector is equipped with a lens shift function for adjusting the position of the projected image by turning the lens shift dials. The lens can be shifted within the range shown below. Description of symbols: V indicates vertical (height of the projected image),
NEC NP-PA521U | User's Manual - Page 204
Ceiling/front projector 9. Appendix 0.1V 0.3H 1H 0.3H 0.1H 0.1H PA622U/PA621U/PA522U/PA521U Desk/front projection Ceiling/front projector 1V 0.6V Height of projected image Width of projected image Width of projected image 0.5V 1V 0.1V Height of projected image 0.1H 0.1H 0.3H*1 1H
NEC NP-PA521U | User's Manual - Page 205
 Compatible Input Signal List Analog Computer Signal VGA SVGA XGA XGA+ Signal WXGA Quad-VGA SXGA SXGA+ WXGA+ WXGA++ UXGA WSXGA+ WUXGA 2K Full HD MAC 13" MAC 16" MAC 19" MAC 21" MAC 23" Resolution ( dots ) 640 × 480 800 × 600 1024 × 768 *1 1152 × 864 1280 × 768 *2 1280 × 800 *2 1360 × 768 *5
NEC NP-PA521U | User's Manual - Page 206
HDMI VGA SVGA XGA HD Signal WXGA Quad-VGA SXGA SXGA+ WXGA+ WXGA++ WSXGA+ UXGA Full HD WUXGA 2K QXGA iPad 9.7" 4M WQHD iMac 27" WQXGA 4K HDTV(1080p) HDTV(1080i) HDTV (720p) SDTV (480p) SDTV (576p) SDTV(480i) SDTV(576i) Resolution ( dots ) 640 × 480 800 × 600 1024 × 768 *1 1280 × 720 *2 1280 ×
NEC NP-PA521U | User's Manual - Page 207
9. Appendix DisplayPort VGA SVGA XGA HD Signal WXGA Quad-VGA SXGA SXGA+ WXGA+ WXGA++ WSXGA+ UXGA Full HD WUXGA 2K QXGA iPad 9.7" 4M WQHD iMac 27" WQXGA 4K HDTV(1080p) HDTV (720p) SDTV (480p) SDTV (576p) Resolution ( dots ) 640 × 480 800 × 600 1024 × 768 *1 1280 × 720 *2 1280 × 768 *2 1280 ×
NEC NP-PA521U | User's Manual - Page 208
PA672W/PA671W/PA572W/PA571W: 1,024,000 (1280 dots × 800 lines) PA622U/PA621U/PA522U/PA521U: 2,304,000 (1920 dots × 1200 lines) Manual (zoom range depends on lens) Manual Manual PA722X/PA721X/PA672W/PA671W/PA622U/PA621U: 355 W PA622X/PA621X/PA572W/PA571W/PA522U/PA521U: 330 W (264W when Eco mode is on
NEC NP-PA521U | User's Manual - Page 209
9. Appendix Model name Computer/ Component HDMI Video input Video output Audio input Audio output Video input DisplayPort Audio input Video input Audio input BNC (CV) Video input Audio input BNC (Y/C) Video input Audio input PC control connector USB port USB port for wireless LAN
NEC NP-PA521U | User's Manual - Page 210
 Cabinet Dimensions Unit: mm (inch) 9. Appendix 368.1 (14.5) 359 (14.1) 162 (6.4) 142 (5.6) 78.5 (3.1) 200 (7.9) 499 (19.6) Lens center 250 (9.8) Lens center 198 Holes for ceiling mount Unit: mm (inch)
NEC NP-PA521U | User's Manual - Page 211
 Mounting the cable cover (sold separately) 9. Appendix Mounting the separately sold cable cover on the projector allows you hide the cables for a cleaner appearance. CAUTION • After mounting the cable cover, be sure to fasten using the screws provided. If not, the cable cover could fall,
NEC NP-PA521U | User's Manual - Page 212
9. Appendix  Pin Assignments of D-Sub COMPUTER Input Connector Mini D-Sub 15 Pin Connector 11 12 13 14 15 6 7 8 9 10 1 23 45 Signal Level Video signal : 0.7Vp-p (Analog) Sync signal : TTL level Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 RGB Signal (Analog) Red Green or Sync on Green Blue
NEC NP-PA521U | User's Manual - Page 213
9. Appendix  Troubleshooting This section helps you resolve problems you may encounter while setting up or Cover problem The lamp cover is not properly mounted. Mount it properly. (→ Page 161) Fan problem The cooling fan has stopped turning. Contact an NEC projector customer support center
NEC NP-PA521U | User's Manual - Page 214
has failed Lamp replacement grace The lamp has reached the end of its service life and period is now in the replacement grace period (100 hours). Replace to a cool place. If the problem still persists, contact an NEC projector customer support center. Lit Orange High surrounding
NEC NP-PA521U | User's Manual - Page 215
page 214.) Problem Check These Items refer to the user guide accompanied with your computer or graphics card, or contact the support center for your computer manufacturer. Install the updated driver or OS on your own responsibility. We are not liable for any trouble
NEC NP-PA521U | User's Manual - Page 216
) • Check the computer's resolution and frequency. Make sure that the resolution you are trying to display is supported by the projector. (→ page 207) • Adjust the computer image manually with the Horizontal/Vertical in the [IMAGE OPTIONS]. (→ page 95) • Install new batteries.(→ page 9) • Make sure
NEC NP-PA521U | User's Manual - Page 217
changes to take affect. For setting display modes other than those supported by your Macintosh and the projector, changing the DIP switch × 768 unless "mirroring" is off on your PowerBook. Refer to owner's manual supplied with your Macintosh computer for mirroring. • Folders or icons are hidden on
NEC NP-PA521U | User's Manual - Page 218
6 PC Control Codes and Cable Connection PC Control Codes Function POWER ON POWER OFF INPUT SELECT COMPUTER 1 INPUT SELECT COMPUTER 2 INPUT SELECT COMPUTER 3 INPUT SELECT HDMI INPUT SELECT DisplayPort INPUT SELECT VIDEO INPUT SELECT S-VIDEO INPUT SELECT VIEWER INPUT SELECT NETWORK PICTURE MUTE ON
NEC NP-PA521U | User's Manual - Page 219
service personnel, check the following list to be sure repairs are needed also by referring to the "Troubleshooting" section in your user's manual. This checklist below will help us solve your problem contrast. Input source's resolution and frequency are supported by the projector. Image is too dark.
NEC NP-PA521U | User's Manual - Page 220
In the space below please describe your problem in detail. 9. Appendix Information on application and environment where your projector is used Projector Model number: Serial No.: Date of purchase: Lamp operating time (hours):
NEC NP-PA521U | User's Manual - Page 221
© NEC Display Solutions, Ltd. 2013 7N951971