NEC NP-PE401H MP300CM Installation Manual
NEC NP-PE401H Manual
 |
View all NEC NP-PE401H manuals
Add to My Manuals
Save this manual to your list of manuals |
NEC NP-PE401H manual content summary:
- NEC NP-PE401H | MP300CM Installation Manual - Page 1
NEC Display Solutions of America, Inc. Installation and Assembly Manual: Custom Ceiling Mount for NEC M260X, M260W, M271X, M300X, M300W M300XS, M300WS, M311X, M311W, P350X, P350W, P420X Projectors Model: MP300CM Features: • ImageLockTM alignment prevents picture sag or drift • Wrench access slot - NEC NP-PE401H | MP300CM Installation Manual - Page 2
these instructions. • Make sure that the supporting surface will safely support the None None None Contact Customer Service Contact Customer Service Contact Customer Service Tools Needed for Assembly • stud to Projector...8 Attaching Adapter Plate to Projector Mount...9 Projector Alignment... - NEC NP-PE401H | MP300CM Installation Manual - Page 3
Before you start check the parts list to insure all of the parts shown are included. Parts List Description A projector mount assembly B 4 mm security allen wrench C #10-32 x 3/8" serrated washer head socket pin screw D #10-32 x 1/4" socket pin screw E flat washer F #14 x 2.5 phillips hex head - NEC NP-PE401H | MP300CM Installation Manual - Page 4
Installation to Extension Column / Ceiling Plate 1 NOTE: Refer to accompanying instructions with ceiling plates (sold separately) for installing these models to ceiling. Screw projector mount assembly (A) onto extension column as shown in figure 1.1. Tighten swivel stop screw against extension - NEC NP-PE401H | MP300CM Installation Manual - Page 5
To Wood Joist Ceilings WARNING • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • Tighten wood screws so that projector mount assembly is firmly attached, but do not overtighten. Overtightening - NEC NP-PE401H | MP300CM Installation Manual - Page 6
minimum. Lighter density concrete may not hold concrete anchor. • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. 3 Place projector mount assembly (A) on ceiling as a template and mark the center of the two - NEC NP-PE401H | MP300CM Installation Manual - Page 7
two 1/4-20 hex thin nylon-insert locknuts (not included) on two 1/4-20 threaded rods (not included) to the desired height of projector mount assembly. Attach projector mount assembly (A) to the two 1/4-20 threaded rods using two 1/4-20 hex thin nylon-insert locknuts as shown in figure 4.1 or - NEC NP-PE401H | MP300CM Installation Manual - Page 8
serrated socket pin screws (BB) and retaining spacers (CC) as shown below. Tighten using 4 mm allen wrench (B). NOTE: Retaining spacers (CC) go between the projector and adapter plate (AA). BB AA CC Visit the Peerless Web Site at www.peerlessmounts.com 8 of 10 ISSUED: 10-01-10 SHEET #: 056 - NEC NP-PE401H | MP300CM Installation Manual - Page 9
OF MOUNT FRONT OF MOUNT A EE CAPTIVE SCREW 8 IMPORTANT: For security installations, insert one #10-32 x 1/4" socket pin screw (D) through projector mount assembly (A) and into connection block (EE) as shown in detail 1. Tighten screw using 4mm security allen wrench (B). A D EE DETAIL - NEC NP-PE401H | MP300CM Installation Manual - Page 10
KNOB FOR ROLL ADJUSTMENT 9-1 To prevent tampering with the pitch and roll adjustments: Tighten the two tamper resistant security screws on the projector mount assembly using 4 mm security allen wrench (B) to lock the pitch and roll adjustments as shown below. Note: Tighten screws firmly, but
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
 |
 |
ISSUED: 10-01-10
SHEET #: 056-9034-4
07-29-11
Visit the Peerless Web Site at www.peerlessmounts.com
1 of 10
For customer care call 1-800-865-2112
Installation and Assembly Manual:
Custom Ceiling Mount for NEC M260X, M260W, M271X, M300X,
M300W M300XS, M300WS, M311X, M311W, P350X, P350W, P420X
Projectors
Model: MP300CM
Features:
• ImageLock
TM
alignment prevents picture sag or drift
• Wrench access slot for easier flush mount installations
• Exclusive aluminum track quick release
NEC Display Solutions of America, Inc.
Max UL Load Capacity:
50 lb (22.7 kg)