Home » NEC Manuals » Projectors » NEC NP-UM361Xi-TM » Manual Viewer

NEC NP-UM361Xi-TM Interactive Software / EyeRIS NEC Edition

NEC NP-UM361Xi-TM Manual

View all NEC NP-UM361Xi-TM manuals

Add to My Manuals
Save this manual to your list of manuals

NEC NP-UM361Xi-TM manual content summary:

NEC NP-UM361Xi-TM | Interactive Software / EyeRIS NEC Edition - Page 1
IWB Setup Software/EyeRIS NEC edition OPERATION MANUAL This manual describes installation and operation procedures of the driver / the calibration software Supported model • NP03Wi • NP04Wi • UM352W (for the remote pen function) • NP01TM © NEC Display Solutions, Ltd. 2015 ver.2 7/15 1
NEC NP-UM361Xi-TM | Interactive Software / EyeRIS NEC Edition - Page 2
the software. Access to our projector support page in our website with the below URL: http://www.nec-display.com/dl/en/index.html Find the software for the IWB Setup Software, EyeRIS, download and install it onto the computer according to the displayed instructions
NEC NP-UM361Xi-TM | Interactive Software / EyeRIS NEC Edition - Page 3
the terms in the License Agreement" and click "Next>" Displays the selection screen of the installation destination folder. 5. Click [Next>]. After that, follow the displayed instructions to complete installation. When the installation is complete, an EyeRIS icon is added to the desktop. 3
NEC NP-UM361Xi-TM | Interactive Software / EyeRIS NEC Edition - Page 4
] in the start menu, and double-click [Add or Remove Programs]. 2. Right-click [EyeRIS] and click [Uninstall] in the list. After that, follow the displayed instructions to complete uninstallation. 3. When uninstallation is completed properly, reboot the computer. 4
NEC NP-UM361Xi-TM | Interactive Software / EyeRIS NEC Edition - Page 5
and follow the displayed instructions for the sequel the computer Switch to the troubleshooting screen Indicate status of the calibration is not performed, or the trouble shooting is displayed on Close EyeRIS automatic calibration Exit EyeRIS Perform manual calibration Perform calibration of the
NEC NP-UM361Xi-TM | Interactive Software / EyeRIS NEC Edition - Page 6
the message in below is displayed on the screen, refer to the Troubleshooting on page 10 and check if the screen is installed within the recognition influence of external light. Perform Calibration Manually [Manual Calibration] 1. Click [Start Manual] button on the displayed calibration menu.
NEC NP-UM361Xi-TM | Interactive Software / EyeRIS NEC Edition - Page 7
the USB cable is disconnected, it may cause of unstable computer motion. • If a check mark is added to the "Auto Run" in the trouble shooting screen, the software starts automatically when the computer is started up. • Drawing software is required to use the interactive white board function. Drawing
NEC NP-UM361Xi-TM | Interactive Software / EyeRIS NEC Edition - Page 8
the Touch Module at the top of the screen according to the installation manual supplied with the Touch Module. Then adjust the Touch module to emit the be performed. If error is happened during the automatic calibration, the manual calibration menu will be displayed. (→ page 6) Pull out the USB cable
NEC NP-UM361Xi-TM | Interactive Software / EyeRIS NEC Edition - Page 9
(2) Select the distance from the touch module to the blue dot on the screen. If you change the setting, the blue dot position will move upward or downward. For using the small screen, select the "FAR". For using the large screen, select the "Close". (3) Turn the adjustment dial A counterclockwise
NEC NP-UM361Xi-TM | Interactive Software / EyeRIS NEC Edition - Page 10
stylus pen. A red square is indicated on the troubleshooting screen and it can be checked all area of projector orientation is DESKTOP, a red square on the trouble shooting screen is indicated at the 180° opposite from problem by performing automatic calibration, try to perform manual calibration. 10