NEC PX-50XM1A 50MP1
NEC PX-50XM1A Manual
 |
View all NEC PX-50XM1A manuals
Add to My Manuals
Save this manual to your list of manuals |
NEC PX-50XM1A manual content summary:
- NEC PX-50XM1A | 50MP1 - Page 1
PlasmaSync Plasma Monitor User's Manual NEC Technologies - NEC PX-50XM1A | 50MP1 - Page 2
this manual carefully before using your NEC plasma monitor and keep the manual handy for future reference. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL - NEC PX-50XM1A | 50MP1 - Page 3
supplied). DVI cable (not supplied) band band Connector core (small) core (small) Power cable (supplied) core (large) band Set side (Plasma Monitor side) To avoid damage and prolong operating life: 1. Use only with 120V 50/60Hz AC power supply it serviced by an authorized NEC Service Center. - NEC PX-50XM1A | 50MP1 - Page 4
NEC produise des panneaux à affichage plasma avec plus de 99,99 % de cellules actives, il peut y avoir des cellules qui ne produisent pas de lumière ou qui restent allumées. Pour des raisons de sécurité et pour éviter d'endommager l'appareil, lire attentivement les instructions NEC pour le service - NEC PX-50XM1A | 50MP1 - Page 5
à plasma) Pour éviter des dommages et prolonger la durée de service de l'appareil: 1. N'utiliser qu'une source d'alimentation de 120 V 50/ 60 service agréé NEC. 5. Ne pas frapper ou rayer la surface de la écran plasma, car des défauts risquent de se produire sur la surface de la écran plasma. - NEC PX-50XM1A | 50MP1 - Page 6
Plasma Monitors NEC Technologies, Inc. (hereinafter NECTECH) warrants this product to be free from defects in material and workmanship under the following terms and, subject to the conditions set forth below, agrees to repair or replace (at NECTECH's sole option) any part instructions supplied with - NEC PX-50XM1A | 50MP1 - Page 7
Options to the Plasma Monitor .... 1 Introduction 2 Introduction to the PlasmaSync 50MP1 Plasma Monitor 2 The features you'll enjoy include 2 Contents of the Package 2 Options 2 Part Names and Function 3 Front View 3 Rear View / Terminal Board 4 Remote Control Unit 5 Battery Installation - NEC PX-50XM1A | 50MP1 - Page 8
to Attach Options to the Plasma Monitor You can attach your optional mounts or stand to the plasma monitor in one of the following installation and mounting it is strongly recommended to use a trained, authorized NEC dealer. Failure to follow correct mounting procedures could result in damage to - NEC PX-50XM1A | 50MP1 - Page 9
HD input (2). Contents of the Package Ⅺ PlasmaSync™ 50MP1 plasma monitor Ⅺ Power cord Ⅺ RGB cable (Mini D-Sub 15-pin to Mini D-Sub 15pin connector) Ⅺ Adapter for Macintosh Ⅺ Remote control unit with two AAA Batteries Ⅺ User's manual Ⅺ Remote cable Ⅺ Safety metal fittings* Ⅺ Screws for safety metal - NEC PX-50XM1A | 50MP1 - Page 10
as the EXIT buttons in the On-Screen Menu (OSM) mode. t POWER/STANDBY indicator When the power is on Lights green. When the power is in the standby mode ... Lights red. y Power Turns the monitor's power on and off. u Remote sensor window Receives the signals from the remote control unit. 3 - NEC PX-50XM1A | 50MP1 - Page 11
(DVI 29pin) Inputs a digital RGB signal (TMDS). G CONTROL LOCK When "CONTROL LOCK" is set "ON", the buttons on the set's control panel do not function. H REMOTE CONTROL Connect the supplied remote cable here. I EXTERNAL CONTROL This terminal is used when power ON/OFF, input selection and AUDIO MUTE - NEC PX-50XM1A | 50MP1 - Page 12
Remote Control Unit q POWER ON/OFF Switches Power ON/OFF. (This does not operate when POWER/STANDBY indicator of the main unit is off.) w RGB/PC Press this button to select RGB/PC as the source. → RGB/PC1 → RGB/PC2 → RGB/PC3 RGB/PC can also be selected using the INPUT SELECT button on the monitor. - NEC PX-50XM1A | 50MP1 - Page 13
contains dark areas above and below the picture. !8 Remote control signal transmitter Transmits the remote control signals. !9 Remote Jack Insert the plug of the supplied remote cable here when using the supplied remote control unit in the wired condition. Battery Installation and Replacement - NEC PX-50XM1A | 50MP1 - Page 14
wired remote control mode Connect the supplied remote cable to the remote control unit's remote jack and the "REMOTE CONTROL" terminal on the monitor. When the cable is connected, the mode automatically switches to wired remote control. When the wired remote control mode is used, the remote control - NEC PX-50XM1A | 50MP1 - Page 15
/PB HD VD L(MONO) R RGB 3 (Digital RGB) CONTROL LOCK ON /OFF REMOTE CONTROL EXTERNAL CONTROL To video inputs on the plasma monitor Document Camera IBM VGA or Compatibles Macintosh or Compatibles (Desk top type) Monitor adapter for Macintosh (supplied) Signal cable (supplied) To Mini D-Sub 15 pin - NEC PX-50XM1A | 50MP1 - Page 16
support XGA/SVGA/VGA you will need to install an XGA/SVGA/VGA graphics board. Consult your computer's owner's manual for your XGA/ SVGA/VGA configuration. If you need to install a new board, see the manual that comes with your new graphics board for installation instructions. 3. The plasma monitor - NEC PX-50XM1A | 50MP1 - Page 17
MONO) R RGB 3 (Digital RGB) CONTROL LOCK ON /OFF REMOTE CONTROL EXTERNAL CONTROL External speakers may be connected to the plasma monitor to reproduce sound from VIDEO, DVD impedance and a power input rating of 7 watts or more. To connect external speakers directly to the plasma monitor: 1. Strip - NEC PX-50XM1A | 50MP1 - Page 18
No connection DDC Clock DDC Data No connection T.M.D.S Data 1 T.M.D.S Data 1 + T.M.D.S Data 1 Shield No connection No connection +5V Power Ground Hot Plug Detect T.M.D.S Data 0 T.M.D.S Data 0 + T.M.D.S Data 0 Shield No connection No connection T.M.D.S Clock Shield T.M.D.S Clock + T.M.D.S Clock No - NEC PX-50XM1A | 50MP1 - Page 19
ON and OFF: 1. Plug the power cord into an active AC power outlet. 2. Press the POWER ON button (on the remote control unit) to turn on the unit. The monitor's POWER/STANDBY indicator will light up (green) when the unit is on. 3. Press the POWER OFF button (on the remote control unit or the unit) to - NEC PX-50XM1A | 50MP1 - Page 20
OFF TIMER button twice in a row. 2. The off timer is canceled. OFF TIMER0 OFF TIMER30 Note: After the power is turned off with the off timer ... A slight current is still supplied to the monitor. When you are leaving the room or do not plan to use the system for a long period of time - NEC PX-50XM1A | 50MP1 - Page 21
WIDE Operations Watching with a wide screen (manual) With this function, you can select one of four screen sizes. When watching videos or digital video discs STADIUM size screen 1. Press the WIDE button on the remote control unit. 2. Within 3 seconds ... Press the WIDE button again. The screen - NEC PX-50XM1A | 50MP1 - Page 22
4 : 3 image to fill the entire screen. 1. Press the WIDE button on the remote control unit. 2. Within 3 seconds ... Press the WIDE button again. The screen size switches on the display output of the various VESA signal standards supported by the monitor. Ⅵ "PICTURE SIZE" setting When the setting of - NEC PX-50XM1A | 50MP1 - Page 23
the selection of the input signal. The INPUT SELECT button on the monitor can also be used to change the selection. Side by side 2 VIDEO1 RGB/PC1 Sub screen Main screen Press the cursor buttons ᮤ ᮣ on the remote control unit to switch the position of the sub screen. VIDEO1 RGB/PC1 Main screen - NEC PX-50XM1A | 50MP1 - Page 24
EXIT EXIT 5. The change is stored until you adjust it again. 6. Repeat steps 2 - 5 to adjust an additional item, or press the EXIT button on the remote control unit to return to the main menu. Note: The main menu disappears by pressing the EXIT button. The following describes how to use the menus - NEC PX-50XM1A | 50MP1 - Page 25
Yes Yes Yes Yes No Yes Yes Sub menu OSM OSM ADJ. POWER MGT GRAY LEVEL CINEMA MODE RGB3 ADJ. LONG LIFE RESET Functions Default . Adjusts the vertical and horizontal positions of the menu display. 1 Sets the monitor for use as an energy-saving display when used with a OFF computer. In - NEC PX-50XM1A | 50MP1 - Page 26
picture The contrast, brightness, sharpness, color and tint can be adjusted as desired. Example: Adjusting the contrast Press the PROCEED button on the remote control unit to display the MAIN MENU on the screen, then... 1. Use the L and M buttons to select "PICTURE", then press the PROCEED button - NEC PX-50XM1A | 50MP1 - Page 27
effectively according to the environment in which you are viewing the display. Example: Setting the "THEATER" mode Press the PROCEED button on the remote control unit to display the MAIN MENU on the screen, then... 1. Use the L and M buttons to select "PICTURE", then press the PROCEED button. The - NEC PX-50XM1A | 50MP1 - Page 28
Setting the color temperature Use this procedure to set color tone produced by the plasma display. Example: Setting "1" Press the PROCEED button on the remote control unit to display the MAIN MENU on the screen, then... 1. Use the L and M buttons to select "PICTURE", then press the PROCEED button. - NEC PX-50XM1A | 50MP1 - Page 29
for bright pictures and dark pictures to achieve the desired color quality. Example: Adjusting the "WHITE BALANCE" Press the PROCEED button on the remote control unit to display the MAIN MENU on the screen, then... 1. Use the L and M buttons to select "PICTURE", then press the PROCEED button. The - NEC PX-50XM1A | 50MP1 - Page 30
to poor reception or when playing video tapes on which the picture quality is poor. Example: Setting "NR-3" Press the PROCEED button on the remote control unit to display the MAIN MENU on the screen, then... 1. Use the L and M buttons to select "PICTURE", then press the PROCEED button. The "PICTURE - NEC PX-50XM1A | 50MP1 - Page 31
The treble, bass and left/right balance can be adjusted to suit your tastes. Example: Adjusting the bass Press the PROCEED button on the remote control unit to display the MAIN MENU on the screen, then... 1. Use the L and M buttons to select "SOUND", then press the PROCEED button. The "SOUND - NEC PX-50XM1A | 50MP1 - Page 32
be adjusted and flickering of the image can be corrected. Example: Adjusting the vertical position in the normal mode Press the PROCEED button on the remote control unit to display the MAIN MENU on the screen, then... 1. Use the L and M buttons to select "SCREEN", then press the PROCEED button. The - NEC PX-50XM1A | 50MP1 - Page 33
manually monitor for presentations, etc., the monitor can be set so that the input source, screen mode, etc., do not appear. Example: Turning the on-screen display mode off Press the PROCEED button on the remote control : ON ↔ OFF FUNCTION OSM OSM ADJ. POWER MGT GRAY LEVEL CINEMA MODE RGB3 ADJ. LONG - NEC PX-50XM1A | 50MP1 - Page 34
the position of the menu display Press the PROCEED button on the remote control unit to display the MAIN MENU on the screen, then... 1. To adjust the position... Adjust using the ᮤ and ᮣ buttons. FUNCTION OSM OSM ADJ. POWER MGT GRAY LEVEL CINEMA MODE RGB3 ADJ. LONG LIFE RESET : ON :2 : OFF :3 - NEC PX-50XM1A | 50MP1 - Page 35
computer images This energy-saving (power management) function automatically reduces the monitor's power consumption if no operation is performed for a certain amount of time. Example: Turning the power management function on Press the PROCEED button on the remote control unit to display the MAIN - NEC PX-50XM1A | 50MP1 - Page 36
/STANDBY indicator Power management POWER/STANDBY Power management mode indicator operating status Description Turning the picture back on On Green Not activated. Horizontal and vertical synchronizing signals are present from the computer. - NEC PX-50XM1A | 50MP1 - Page 37
parts on the screen on which nothing is displayed when the screen is set to the 4:3 size. Example: Adjusting the "GRAY LEVEL" Press the PROCEED button on the remote control ᮣ button is pressed: → ON ↔ OFF ← FUNCTION OSM OSM ADJ. POWER MGT GRAY LEVEL CINEMA MODE RGB3 ADJ. LONG LIFE RESET : ON :1 : - NEC PX-50XM1A | 50MP1 - Page 38
the ᮤ or ᮣ buton is pressed: → 1 ↔ 2 ↔ 3 ← FUNCTION OSM OSM ADJ. POWER MGT GRAY LEVEL CINEMA MODE RGB3 ADJ. LONG LIFE RESET : ON :1 : OFF :3 : ON :2 Example: Setting "PLE" to "LOCK" Press the PROCEED button on the remote control unit to display the MAIN MENU on the screen, then proceed as follows. - NEC PX-50XM1A | 50MP1 - Page 39
remote control unit to display the MAIN MENU on the screen, then... 1. Use the L and M buttons to select "FUNCTION", then press the PROCEED button. The "FUNCTION" screen appears. 2. Use the L and M buttons to select "RESET", then press the PROCEED button. FUNCTION OSM OSM ADJ. POWER - NEC PX-50XM1A | 50MP1 - Page 40
set the input of the 5 BNC connectors to RGB or component. Example: Set the BNC SELECT mode to "COMP." Press the PROCEED button on the remote control unit to display the MAIN MENU on the screen, then... 1. Use the L and M buttons to select "OPTION", then press the PROCEED button. The "OPTION - NEC PX-50XM1A | 50MP1 - Page 41
image such as (video) mode, wide mode or digital broadcast. Example: Setting the "RGB SELECT" mode to "MOTION " Press the PROCEED button on the remote control unit to display the MAIN MENU on the screen, then... 1. Use the L and M buttons to select "OPTION", then press the PROCEED button. The - NEC PX-50XM1A | 50MP1 - Page 42
of input signals as listed in the table "Computer input signals supported by this system" on page 47. STILL To display VESA standard Example: Setting the "1080B" mode to "1035I" Press the PROCEED button on the remote control unit to display the MAIN MENU on the screen, then... 1. Use the L - NEC PX-50XM1A | 50MP1 - Page 43
signals Use this procedure to switch the setting to "ON" or "OFF". Example: Setting the "ON" mode to "OFF" Press the PROCEED button on the remote control unit to display the MAIN MENU on the screen, then... 1. Use the L and M buttons to select "OPTION", then press the PROCEED button. The "OPTION - NEC PX-50XM1A | 50MP1 - Page 44
Use these operations to set the video signal format. Example: Setting the video signal format to "3.58 NTSC" Press the PROCEED button on the remote control unit to display the MAIN MENU on the screen, then... 1. Use the L and M buttons to select "INFORMATION", then press the PROCEED button. The - NEC PX-50XM1A | 50MP1 - Page 45
4. Once the setting is completed ... Press the EXIT button to return to the main menu. To delete the main menu, press the EXIT button once more. The color system is set to "3.58 NTSC". Information Ⅵ Video signal formats Different countries use different formats for video signals. Set to the format - NEC PX-50XM1A | 50MP1 - Page 46
(3) Baud rate 9600 bps (4) Data length 8 bits (5) Parity Odd (6) Stop bit 1 bit (7) Communication code Hex 1) Connector on the plasma monitor side: EXTERNAL CONTROL connector. Type of connector: D-Sub 9-pin male No. Pin Name 1 No Connection 2 RXD (Receive data) 3 TXD (Transmit data) 4 DTR - NEC PX-50XM1A | 50MP1 - Page 47
as in 3FH and 7FH), this indicates that the commands and data of the supported equipment have been received. When the lower order 4 bits is BH (as in that is to be connected. 60H is used for the plasma monitor and 80H is used for external control equipment such as a personal computer. 1) Unit ID 1: - NEC PX-50XM1A | 50MP1 - Page 48
Gain Flag 01H DATA02 VOLUME Gain 00H: Step 0 01. Power ON Function The external control equipment switches on the power of the plasma monitor. Transmission Data 9FH 80H 60H 4EH 00H CKS ACK The plasma monitor returns the following ACK when the power is switched on. 0AH: Step 10 (Default) 2AH - NEC PX-50XM1A | 50MP1 - Page 49
10.TINT Gain Data Function The external control equipment changes the TINT gain data of the plasma monitor. Transmission Data DFH 80H 60H 7FH 03H Flag 01H DATA01: TINT Gain Flag 05H Operation Remote control operation Personal computer control operation On-Screen Display (OSD) Display of items - NEC PX-50XM1A | 50MP1 - Page 50
Gain Flag DATA02: BRIGHT Gain 01H 08H E0H: -32 FFH: -01 00H: 0 01H: +01 16. COLOR TEMP SELECT Function The external control equipment changes the COLOR TEMP of the plasma monitor. Transmission Data DFH 80H 60H 00H 01H DATA00 CKS DATA00 ACK 00H: 1 01H: 2 02H: 3 03H: PRO 7FH 60H 80H 00H 01H - NEC PX-50XM1A | 50MP1 - Page 51
18. GREEN Gain Data Function The external control equipment changes the GREEN Gain Data of the plasma monitor. Transmission Data DFH 80H 60H 7FH screen L 04: Picture in Picture sub screen R When other commands (except POWER OFF) are sent while the screens are switching with this command, the other - NEC PX-50XM1A | 50MP1 - Page 52
21. VIDEO ADJ Request Function The display returns the video adjustments information by the external control equipment's request. Transmission Data 1FH 80H 60H 45H 00H CKS ACK 7FH 60H 80H 45H 0CH DATA00 to DATA0B CKS DATA00: RED Gain(Bias) D8H: - - NEC PX-50XM1A | 50MP1 - Page 53
(DTV2) 07H: RGB 1 /PC 1 08H: RGB 2 /PC 2 0CH: RGB 3 /PC 3 24. LONG LIFE Set Function The external control equipment sets the PLE, ORBITER, and INVERSE (inverse of image brightness) of the plasma monitor. Transmission Data DFH 80H 60H 6BH 03H DATA00 DATA01 DATA02 CKS DATA00 : PLE 01H: AUTO 02H: LOCK - NEC PX-50XM1A | 50MP1 - Page 54
signal. (Except for *3) Computer input signals supported by this system Model Vertical Dots ןlines frequency Signal Type - - - - 63.9 - - - - - - - - PAL625P NTSC525P 768ן576 640ן480 50.0 59.9 31.4 NEG NEG YES YES 31.5 NEG NEG YES YES Screen mode RGB NORMAL TRUE FULL - NEC PX-50XM1A | 50MP1 - Page 55
in the table above. *6 To connect the monitor to Macintosh computer, use the supplied monitor adapter (D-Sub 15-pin) to your computer's monitor, the picture will be compressed. • This monitor has a resolution of 1365 dot ן768 line. It is recommended that the input signal should be XGA, wide XGA - NEC PX-50XM1A | 50MP1 - Page 56
the problem persists, contact your NEC dealer for service. *2 In the following case, power off the monitor immediately and contact your dealer or authorized NEC Center. The monitor turns off 5 seconds after powering on and then the POWER/STANDBY indicator blinks. It indicates that the power supply - NEC PX-50XM1A | 50MP1 - Page 57
Specifications Product Name PlasmaSync™ 50MP1 Plasma Monitor Product Code PX- 50XM1A Screen Size 43.5"(H)ן24.5"(V) inches 1106(H)ן622(V) mm diagonal 50" Aspect Ratio 16 : 9 Resolution 1365(H)ן768(V) pixels Pixel Pitch 0.032"(H)ן0.032"(V) inches 0.81(H)ן0.81(V) mm Color - NEC PX-50XM1A | 50MP1 - Page 58
- NEC PX-50XM1A | 50MP1 - Page 59
- NEC PX-50XM1A | 50MP1 - Page 60
NEC Technologies, Inc. 1250 N. Arlington Heights Road, Suite 500 Itasca, Illinois 60143-1248 51 Printed on recycled paper Printed in Japan 7S800062
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
 |
 |
PlasmaSync Plasma Monitor
User’s Manual
NEC Technologies