NEC V554-T User Manual
NEC V554-T Manual
 |
View all NEC V554-T manuals
Add to My Manuals
Save this manual to your list of manuals |
NEC V554-T manual content summary:
- NEC V554-T | User Manual - Page 1
Large Format Display User's Manual MultiSync V404-T MultiSync V484-T MultiSync V554-T MODEL: V404-T, V484-T, V554-T Please find your model name in the label on the rear side of the monitor. - NEC V554-T | User Manual - Page 2
Connection...English-47 Controlling the LCD monitor via RS-232C Remote Control English-48 Controlling the LCD monitor via LAN Control...English- English-62 Troubleshooting...English-63 Specifications - V404-T...English-65 Specifications - V484-T...English-66 Specifications - V554-T...English- - NEC V554-T | User Manual - Page 3
instructions Problems." This booklet is available from the U.S. Government Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4. Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation. MultiSync , see "readme.pdf" inside the "about - NEC V554-T | User Manual - Page 4
be read carefully in order to avoid any problems. CAUTION: Please use the power cord provided cord is not supplied with this equipment, please contact NEC. For all other cases, please use the power being used. NOTE: This product can only be serviced in the country where it was purchased. Use the - NEC V554-T | User Manual - Page 5
with ANSI/NFPA 70, the National Electrical Code (NEC), in particular Section 820.93, Grounding of Outer Conductive the wall outlet and refer servicing to qualified service personnel: • If the power not operate normally by following operating instructions. Recommended Use Ergonomics To realize - NEC V554-T | User Manual - Page 6
glass cleaner! • Please do not rub the LCD panel with hard material. • Please do not apply pressure to the LCD panel surface. • Please do not use OA cleaner as it will cause deterioration or discoloration on the LCD panel surface. Cleaning the Cabinet • Unplug the power supply • Gently - NEC V554-T | User Manual - Page 7
support. For proper installation it is strongly recommended to use a trained, NEC authorized service person. Failure to follow NEC enough to support the LCD monitor before support the weight of the unit so that the unit will be safe from harm. • For detailed information, refer to the instructions - NEC V554-T | User Manual - Page 8
the rear of the LCD monitor: Orientation • be strong enough to support the monitor and mounting problem is detected, please refer to qualified personnel for service. • Regularly check the mounting location for signs of damage or weakness that may occur over time. 3.6 mm LED Indicator Changing NEC - NEC V554-T | User Manual - Page 9
attached with the monitor in the face down position. To avoid scratching the LCD panel, always place a soft cloth, such as a blanket that is larger that can damage the monitor. When using mounting accessories other than NEC compliant and approved, they must comply with the VESA Flat Display Mounting - NEC V554-T | User Manual - Page 10
follow the instructions included with the stand. When installing the LCD monitor stand, handle the to the ST-401 user's manual for more detail. NOTE: DO or with a mounting accessory for support. Height adjustment 1. The lines on the room. 100 mm Pipe V554-T V484-T V404-T Adjust the - NEC V554-T | User Manual - Page 11
wireless remote control). See also page 13. Glows blue when the LCD monitor is in active mode*. Green and Amber blink alternately when selected in the "POWER INDICATOR" (see page 42), the LED will not glow when the LCD monitor is in active mode. *1 If "OFF" is selected in the "SCHEDULE INDICATOR" ( - NEC V554-T | User Manual - Page 12
from a computer or HDTV device having a digital RGB output. * This connector does not support analog input. I RS-232C IN (D-Sub 9 pin) Connect RS-232C input from external port. USB CM1 (2A): Power supply port. USB CM2*: Service port. Please do not connect devices. * USB functionality is available - NEC V554-T | User Manual - Page 13
Slot Slot for installing a Raspberry Pi Compute Module Interface Board and Raspberry Pi Compute Module. Please refer to https://www.nec-display.com/dl/en/manual/raspberrypi/ for more information. CAUTION: Installation must be performed by a qualified technician. Do not attempt to install a Compute - NEC V554-T | User Manual - Page 14
. N CH/ZOOM UP/DOWN Button (CH/ZOOM +/-)*1 Increases or decreases the POINT ZOOM level. Please refer to POINT ZOOM (See page 58). O GUIDE Button*1 P MUTE Button Turns on/off the mute function. Q PICTURE MODE Button Selects the picture mode, [HIGHBRIGHT], [STANDARD], [sRGB], [CINEMA], [CUSTOM1 - NEC V554-T | User Manual - Page 15
option board you are using. Refer to the option board's user's manual for further information. NOTE: The buttons with no explanation do not for the Remote Control Point the top of the remote control toward the LCD monitor's remote control sensor during button operation. Use the remote control within - NEC V554-T | User Manual - Page 16
see page 40). IMPORTANT: To avoid scratching the LCD panel, always place a soft cloth, such as AAA batteries. To install or replace batteries: NEC recommends the following battery use: • Place " making connections. • Refer to the user's manual of your equipment for further information. NOTE: - NEC V554-T | User Manual - Page 17
English 5. Cable information CAUTION: Use the provided specified cables with this color monitor so as not to interfere with radio and television reception. For mini D-Sub 15-pin, DVI, and USB please use a shielded signal cable with ferrite core. For HDMI, DisplayPort, D-Sub 9-pin and AUDIO, - NEC V554-T | User Manual - Page 18
the sound. Before making connections: * First turn off the power of all the attached equipment and make connections. * Refer to the user's manual included with each separate piece of equipment. * We strongly recommend connecting or disconnecting a USB storage device or a microSD memory card to the - NEC V554-T | User Manual - Page 19
enable you to reproduce your computer's video signal output. Some display cards may not be able to support the required resolution for proper image reproduction. Your LCD monitor shows proper image by adjusting the factory preset timing signal automatically. - NEC V554-T | User Manual - Page 20
66 and page 67). USB CM2: Service port. Please do not connect devices. In this case, please check user's manual of your computer or device, or NEC customer support for more detailed information. Please contact your NEC customer support Troubleshooting" when the touch panel function does not work - NEC V554-T | User Manual - Page 21
English Basic Operation Power ON and OFF Modes The LCD monitor power indicator will turn blue while powered on. NOTE: The Main Power switch must be in the ON position in order to power up - NEC V554-T | User Manual - Page 22
that automatically reduces the power consumption of the monitor when the keyboard or the mouse has not been used for a fixed period. This allows your LCD monitor to enter a Power Management mode if the monitor's POWER SAVE function is set to ENABLE, and a certain amount of time has passed since the - NEC V554-T | User Manual - Page 23
image, which is rotated anticlockwise by 90°. Displayable/playable files Still Supported formats File extension Supported .jpg, .jpeg, .jpe Baseline, Progressive, RGB, CMYK .png Interlace, α channel Motion image Supported formats File extension .mpg, .mpeg .wmv .mp4 .mov .flv, .f4v Video - NEC V554-T | User Manual - Page 24
Format a microSD memory card in the FAT32 format or FAT16 format. Refer to the computer's instruction user's manual or Help file on how to format a microSD memory card. Information Up to 32GB microSDHC is supported. NOTE: It is not guaranteed to work with all microSD memory card sold commercially - NEC V554-T | User Manual - Page 25
the Media Player. Refer to the computer's instruction user's manual or Help file on how to format a USB memory. Please use a USB memory with this monitor in accordance with the drawing below. If the physical size of the USB device is larger than the supported - NEC V554-T | User Manual - Page 26
on the remote control, or "AUTO" in which the images are switched automatically at a set interval (PLAY MODE is "AUTO"). • The default factory setting is "MANUAL". To perform "AUTO", set the "PLAY MODE" to "AUTO". • The images will be displayed in the order selected under "Sort" on the file display - NEC V554-T | User Manual - Page 27
English NETWORK & OTHER SETTINGS Below are the options for the Network settings and Shared Folder settings for the Media Player. To select the settings, press the remote control SET/POINT ZOOM button on the NETWORK & OTHER SETTINGS. NETWORK SETTINGS for MEDIA PLAYER Menu IP SETTING IP ADDRESS - NEC V554-T | User Manual - Page 28
Using SHARED SD card SETTINGS You can copy data to the microSD memory card, such as motion or still images, from a computer connected to the same network as the monitor. Please set the NETWORK SETTINGS for the Media Player (See page 25) first to copy data. NOTE: When the monitor is copying a - NEC V554-T | User Manual - Page 29
in a microSD memory card which is connected to the monitor. Instructions for the EMERGENCY CONTENTS can be found on the CD included with the monitor. The file is called "External_control.pdf". Information OSD The Information OSD provides information such as: Input - NEC V554-T | User Manual - Page 30
Color setting for High-definition television. Highest brightness setting. Native LCD panel color gamut. Suitable for use with color managed applications. the Grayscale Standard Display Function. For the Hardware Calibration by NEC Display Solutions GammaCompMD QA software (some OSD settings are - NEC V554-T | User Manual - Page 31
English GAMMA Allows you to manually select the brightness level of grayscale. There are five selections: , you may experience inaccurate color reproduction. - MultiProfiler software, developed by NEC Display Solutions, is highly recommended to provide extended color management features such - NEC V554-T | User Manual - Page 32
SPECTRAVIEW ENGINE is set to "OFF": Select from five different picture modes, either via the OSD menu item PICTURE MODE, or using the PICTURE MODE button on the wireless remote control. For DVI, DisplayPort1, DisplayPort2, OPTION*, VGA (RGB), HDMI1, HDMI2, C MODULE*2 STANDARD sRGB CINEMA CUSTOM1 - NEC V554-T | User Manual - Page 33
VISION EMU OFF UNIFORMITY OFF METAMERISM ON / OFF COLOR CONTROL R - + 0 Y - + 0 G - + 0 C - + 0 B - + 0 M - + 0 Select Goto Adjustment Return Close Key Guide *: This menu is only available when the optional Raspberry Pi Compute Module Interface Board and Raspberry Pi - NEC V554-T | User Manual - Page 34
parts and lowers the light parts of the image (S-Curve). DICOM SIM. DICOM GSDF curve simulated for LCD type. PROGRAMMABLE1, 2, 3 A programmable gamma curve can be loaded using optional NEC software. COLOR*2 COLOR Adjusts the color depth of the screen. Press + or - to adjust. COLOR TEMPERATURE - NEC V554-T | User Manual - Page 35
YPbPr) inputs only Controls the vertical position of the image within the Display area of the LCD. Press + to move up. Press - to move down. CLOCK VGA (RGB) input 60 INPUT RESOLUTION VGA (RGB) input only If there is a problem with signal detection, this function forces the monitor to display the - NEC V554-T | User Manual - Page 36
ADVANCED OVER SCAN Some video formats may require different scanning modes in order to best display the image. HDMI1, HDMI2, VGA (YPbPr), VIDEO, MP, OPTION*1 inputs only ON Image size is larger than what can be displayed. The image edge will appear cropped. Approximately 95% of the image will - NEC V554-T | User Manual - Page 37
English EQUALIZER TREBLE Accentuate or reduce the high frequency range of audio signals. Press the + button to increase TREBLE. Press the - button to decrease TREBLE. BASS Accentuate or reduce the low frequency sound. Press the + button to increase BASS. Press the - button to decrease BASS. - NEC V554-T | User Manual - Page 38
DATE & TIME Sets the date, time, and daylight savings region. Date & time must be set in order for the "SCHEDULE" function to operate. NOTE: If the monitor's main power has been turned off for two weeks, the DATE & TIME setting goes back to the default setting and the clock function stops working. - NEC V554-T | User Manual - Page 39
English INPUT DETECT Selects the method of input detection the monitor uses when more than one signal source is connected. NOTE: When SUPER is selected within INPUT CHANGE, this function cannot be changed. INPUT DETECT is released if HUMAN SENSOR is activated while INPUT DETECT is active. NONE - NEC V554-T | User Manual - Page 40
and portrait. Shows the OSD in landscape orientation. Shows the OSD in portrait orientation. NOTE: If PORTRAIT is set, CLOSED CAPTION is not available. Key guide is shown when the OSD menu is displayed. NOTE: This function is not available when OSD FLIP is "ON". Defines a title and a message via - NEC V554-T | User Manual - Page 41
English TILE MATRIX Allows one image to be expanded and displayed over multiple screens (up to 100) through a distribution amplifier. NOTE: Low resolution is not suitable for tiling to a large number of monitors. You can operate without a distribution amplifier at a lower number of screens. This - NEC V554-T | User Manual - Page 42
. DNS Set the IP addresses of DNS servers. AUTO: The DNS server, which is connected with the monitor, will automatically assign its IP address. MANUAL: Manually enter the IP address of the DNS server which is connected with the monitor. DNS PRIMARY Enter the primary DNS server settings of the - NEC V554-T | User Manual - Page 43
English CHANGE PASSWORD SECURITY PASSWORD SECURE MODE OFF START-UP LOCK CONTROL LOCK BOTH LOCK IR LOCK SETTINGS MODE SELECT UNLOCK ALL LOCK CUSTOM LOCK KEY LOCK SETTINGS MODE SELECT UNLOCK ALL LOCK CUSTOM LOCK DDC/CI DisplayPort2, DVI, VGA (RGB) Inputs only PING IP ADDRESS EXECUTE IP ADDRESS RESET - NEC V554-T | User Manual - Page 44
function when ROOM LIGHT SENSING is MODE1 or MODE2. The backlight of the LCD screen can be set to increase or decrease depending on the amount of ambient or off. If OFF is selected, the LED will not glow when the LCD monitor is in active mode. SCHEDULE INDICATOR Turns the LED on or off depending - NEC V554-T | User Manual - Page 45
to "The touch panel does not respond" in "Troubleshooting" when the touch panel function does not work. the operating system cannot be shut down manually. SLOT2 CH SETTING Selects signal type according right half. If the internal PC does not support either one of the signal types, the existing - NEC V554-T | User Manual - Page 46
Module. AUTO POWER ON When set to Enable, power to the Compute Module will be turned on automatically when the display power is turned on. SERVICE MENU SETTING LOCK Locks all settings under COMPUTE MODULE. USB BOOT MODE When set to Enable, the Compute Module will appear as a USB device to - NEC V554-T | User Manual - Page 47
a previous image remains visible on the screen. Unlike CRT monitors, LCD monitors' image persistence is not permanent, but a still image being hour to erase the image. As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver - NEC V554-T | User Manual - Page 48
called the REMOTE CONTROL ID mode. The REMOTE CONTROL ID mode works in conjunction with the Monitor ID, allowing control of up to 100 individual MultiSync monitors. For example, if there are many monitors being used in the same area, a remote control in normal mode would send signals to every - NEC V554-T | User Manual - Page 49
-chain connection. NOTE: Multiple monitors that are daisy-chained have a limit to the connectable monitors. Please execute AUTO ID (see page 39) before manually specifying the ID number or control by the specified ID number. Main Monitor Connector IN OUT RS-232C REMOTE IN LAN2 LAN1 Sub - NEC V554-T | User Manual - Page 50
signals. • Sound Mute ON or OFF. Connection LCD Monitor + computer. • Please turn off the monitor diagram (See page 56) or see the "External_Control.pdf" file on the CD-ROM supplied with the monitor. please use the control command. Instructions for the control command can be found on - NEC V554-T | User Manual - Page 51
English 1) Interface PROTOCOL BAUD RATE DATA LENGTH PARITY STOP BIT FLOW CONTROL RS-232C 9600 [bps] 8 [bits] NONE 1 [bit] NONE This LCD monitor uses RXD, TXD and GND lines for RS-232C control. The reverse type cable (null modem cable) (not included) should be used for RS- - NEC V554-T | User Manual - Page 52
Controlling the LCD monitor via LAN Control Connecting to a Network Using a LAN cable allows you to specify the Network Settings and the Alert Mail Settings by using an - NEC V554-T | User Manual - Page 53
name by using a compatible browser. Example 1: When the host name of the monitor has been set to "pd.nec.co.jp", access is gained to the network setting by specifying http://pd.nec.co.jp/index.html for the address or the entry column of the URL. Example 2: When the IP address - NEC V554-T | User Manual - Page 54
address for the monitor connected to the network. NOTE: Consult your network administrator if you have any trouble. IP ADDRESS Set your IP address for the monitor connected to the network when [MANUAL] is selected for [IP SETTING]. SUBNET MASK Set your subnet mask data for the monitor connected - NEC V554-T | User Manual - Page 55
HINT: For the control command diagram, please see the file "External_Control.pdf" on the CD-ROM supplied with this monitor. Alert error message CONTROL-COOLING FAN = AUTO No signal Please check "No picture" in "Troubleshooting". The Proof of Play log memory size is 1 more hour. Please get - NEC V554-T | User Manual - Page 56
will not detect the device. CRESTRON Settings Click on "CRESTRON" on the left column below HOME. CRESTRON ROOMVIEW compatibility The monitor supports CRESTRON ROOMVIEW, allowing multiple devices connected in the network to be managed and controlled from a computer or a controller. For further - NEC V554-T | User Manual - Page 57
Up to 60 alphanumeric characters can be used. Network SERVICE Settings Click on "NETWORK SERVICE" on the left column below HOME. PJLink CLASS Machine and Information System Industries Association (JBMIA) in 2005. The device supports all commands of PJLink. PD LIST Information Click on "PD LIST" - NEC V554-T | User Manual - Page 58
30 32 03 0a 0d ASCII Control command This monitor supports control command, which is listed in the "External_Control.pdf" file on the CD-ROM supplied with the monitor, but also supports common ASCII control command, which is used for controlling the NEC monitor or projector from a connected PC. For - NEC V554-T | User Manual - Page 59
standby at the same time. If the monitor goes into standby while an HDMI CEC supported device is recording, the device is kept on. Please refer to the user's manual supplied with the HDMI CEC supported device for further information. The function sends digital audio signal through the HDMI cable - NEC V554-T | User Manual - Page 60
POINT ZOOM Using the "SET/POINT ZOOM" button on the remote control enlarges part of the screen image. Press the CH+/- button to zoom in or out. The image can be expanded up to 10 times. 1 Press the [SET/POINT ZOOM] button on the remote control. The icon looks like a magnifier. 2 Move the magnifier - NEC V554-T | User Manual - Page 61
④ IN1 ⑤ Normal Picture ⑥ Normal Audio ⑦ 2014/1/1/0h/0m/0s h 10h: MEDIA PLAYER is stop NOTE: For the Proof of Play function, please see the "External_Control.pdf" on the CD-ROM supplied with this monitor. English-59 - NEC V554-T | User Manual - Page 62
INTELLIGENT WIRELESS DATA This function allows to get the monitor status via wireless communication, even while the monitor's main power is off or is not yet installed. Even some OSD items may be set by using this feature. NOTE: Sensor position: See page 9 and page 10. Please contact your - NEC V554-T | User Manual - Page 63
No When the monitor output a signal from the DisplayPort out, Please select input signal DisplayPort1 or OPTION. This monitor's signal output function is supporting contents which is protected by HDCP. In this case, up to 3 monitors are connectable. When using an option, Please set SLOT2 CH SETTING - NEC V554-T | User Manual - Page 64
monitor are exactly the same as on the color printout (with sRGB supporting operating system and sRGB printer). This allows you to adjust the colors to any VESA standard (FDMIv1) third party mounting arm or bracket. NEC recommends using mounting equipment which complies with TÜV-GS (Germany) and/or - NEC V554-T | User Manual - Page 65
Troubleshooting supported resolution has been selected on the display card or system being used. If in doubt, please refer to the user's manual • Please be aware that LCD Technology may experience a phenomenon with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving - NEC V554-T | User Manual - Page 66
a minimum. • Check to see if the computer supports an audio signal through DisplayPort. If unsure, contact your TIMER" function is enabled and the power to the LCD monitor is turned off when the power supply is interrupted . Refer to your USB device user's manual. • Check if the USB upstream port - NEC V554-T | User Manual - Page 67
Product Specifications LCD Module card Hub Port: microSD card. Up to 32GB microSDHC is supported. USB Hub USB1: USB 2.0 Downstream port USB2: USB 2.0 Upstream port USB CM1 2A): Power supply port, 5V/2A (max.) USB CM2: USB service port for maintenance USB MP: Media Player/Firmware update port Power - NEC V554-T | User Manual - Page 68
Specifications LCD Module card Hub Port: microSD card. Up to 32GB microSDHC is supported. USB Hub USB1: USB 2.0 Downstream port USB2: USB 2.0 Upstream port USB CM1 ( 2A): Power supply port, 5V/2A (max.) USB CM2: USB service port for maintenance USB MP: Media Player/Firmware update port Power Supply - NEC V554-T | User Manual - Page 69
V554-T Product Specifications LCD card Hub Port: microSD card. Up to 32GB microSDHC is supported. USB Hub USB1: USB 2.0 Downstream port USB2: USB 2.0 Upstream port USB CM1 2A): Power supply port, 5V/2A (max.) USB CM2: USB service port for maintenance USB MP: Media Player/Firmware update port Power - NEC V554-T | User Manual - Page 70
latest independent standards from agencies such as ISO (International Organisation for Standardization) and TCO (Swedish Trades Union). Disposing of your old NEC product The aim of recycling is to gain an environmental benefit by means of re-use, upgrading, reconditioning or reclamation of material - NEC V554-T | User Manual - Page 71
legislation. According to EU directive 2006/66/EC and amendments, the battery can't be disposed improperly. The battery shall be separated to collect by local service. English-69 - NEC V554-T | User Manual - Page 72
[Notice] About the MPEG-4 AVC, MPEG‑4 Visual license included in this product 1. MPEG-4 AVC THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL USE OF A CONSUMER OR OTHER USES IN WHICH IT DOES NOT RECEIVE REMUNERATION TO (i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
 |
 |
MODEL: V404-T, V484-T, V554-T
Large Format Display
User’s Manual
MultiSync V404-T
MultiSync V484-T
MultiSync V554-T
Please find your model name in the label on the rear side of the monitor.