Netgear DG834Gv3 DG834Gv3 Reference Manual

Netgear DG834Gv3 - 54 Mbps Wireless ADSL Firewall Modem Manual

Get Netgear DG834Gv3 - 54 Mbps Wireless ADSL Firewall Modem PDF manuals and user guides View all Netgear DG834Gv3 manuals
Add to My Manuals
Save this manual to your list of manuals

Netgear DG834Gv3 manual content summary:

  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 1
    Reference Manual for the ADSL Modem Wireless Router DG834G NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA 202-10155-01 January 2006
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 2
    NETGEAR is a trademark of Netgear, Inc. Microsoft, Windows, and Windows installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions with FCC radiation exposure limits set forth for an uncontrolled environment
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 3
    o exigibles de la Directiva 1999/5/CE. Greek] NETGEAR, Inc 54 Mbps ADSL Modem Wireless Router Model DG834G 1999/5/ΕΚ. Français [French] Par la présente NETGEAR, Inc. déclare que l'appareil 54 Mbps ADSL Modem Wireless Router Model DG834G est conforme aux exigences essentielles et aux autres
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 4
    , Inc. izjavlja, da je ta 54 Mbps ADSL Modem Wireless Router Model DG834G v skladu z bistvenimi zahtevami in ostalimi relevantnimi doloèili direktive 1999/5/ ES. Slovensky [Slovak] NETGEAR, Inc. týmto vyhlasuje, že 54 Mbps ADSL Modem Wireless Router Model DG834G spåòa základné požiadavky a všetky
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 5
    to the standards set by the instructions for correct handling. Customer Support Refer to the Support Information Card that shipped with your 54 Mbps ADSL Modem Wireless Router Model DG834G. World Wide Web NETGEAR DG834G v3 January 2006 Modem Router 54 Mbps ADSL Modem Wireless Router Model DG834G
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 6
    vi v1.0, January 2006
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 7
    How to Print this Manual 1-2 Chapter 2 Introduction About the Modem Router 2-1 Key Features ...2-2 A Powerful, True Firewall 2-2 802.11 Standards-based Wireless Networking 2-3 Easy Installation and Management 2-3 Protocol Support ...2-4 Virtual Private Networking (VPN 2-5 Auto Sensing and Auto
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 8
    Your Network Protecting Access to Your 54 Mbps ADSL Modem Wireless Router Model DG834G ....4-1 How to Change the Built-In Password 4-1 Changing the Administrator Login Timeout 4-2 Configuring Basic Firewall Services 4-3 Blocking Keywords, Sites, and Services 4-3 How to Block Keywords and Sites
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 9
    7-2 Gateway-to-Gateway VPN Tunnels 7-3 Planning a VPN ...7-4 VPN Tunnel Configuration 7-6 How to Set Up a Client-to-Gateway VPN Configuration 7-7 Step 1: Configuring the Client-to-Gateway VPN Tunnel on the DG834G v3 ...........7-7 Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 10
    8-8 Restoring the Default Configuration and Password 8-9 Using the Reset button 8-9 Problems with Date and Time 8-9 Appendix A Technical Specifications Appendix B NETGEAR VPN Configuration DG834G v3 to FVL328 B-1 Configuration Profile B-1 Step-By-Step Configuration B-2 DG834G v3 with FQDN to
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 11
    Summary (Telecommuter Example B-14 Setting Up the Client-to-Gateway VPN Configuration (Telecommuter Example) ........ B-15 Step 1: Configuring the Client-to-Gateway VPN Tunnel on the VPN Router at the Employer's Main Office B-15 Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 12
    6 v1.0, January 2006
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 13
    network, Internet, firewall, and VPN technologies tutorial information is provided in the Appendices and on the Netgear website. Note: Product updates are available on the NETGEAR, Inc. Web site at http://kbserver.netgear.com/products/DG834G v3.asp. This guide uses the following typographical
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 14
    or death. This manual is written for the ADSL Modem Wireless Router according to these specifications: Table 1-2. Manual Scope Product Version Manual Publication Date 54 Mbps ADSL Modem Wireless Router Model DG834G January 2006 How to Print this Manual To print this manual you can choose one
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 15
    Manual for the ADSL Modem Wireless Router DG834G - Click the print icon in the upper left of the window. Tip: If your printer supports printing two pages on a single sheet of paper, you can save paper and printer ink by selecting this feature. • Printing the Full Manual. Use the Complete PDF Manual
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 16
    Reference Manual for the ADSL Modem Wireless Router DG834G 1-4 About This Manual v1.0, January 2006
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 17
    this manual. About the Modem Router The 54 Mbps ADSL Modem Wireless Router Model DG834G provides continuous, high-speed 10/100 Ethernet access between your Ethernet devices. With minimum setup, you can install and use the modem router within minutes. The ADSL Modem Wireless Router provides multiple
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 18
    Router DG834G Key Features The ADSL Modem Wireless Router provides the following features: • A built-in ADSL modem • A powerful, true firewall • 802.11g standards-based wireless networking • Easy, Web-based setup for installation and management • Extensive Internet protocol support • Trustworthy VPN
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 19
    be entered manually or generated by passphrase • Support for Wi-Fi Protected Access Pre-Shared Key (WPA-PSK) encryption and 802.1x authentication • Wireless access can be restricted by MAC address Easy Installation and Management You can install, configure, and operate the DG834G v3 within minutes
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 20
    Reference Manual for the ADSL Modem Wireless Router DG834G • Visual monitoring The modem router's front panel LEDs provide an easy way to monitor its status and activity. • Flash erasable programmable read-only memory (EPROM) for firmware upgrades. Protocol Support The DG834G v3 supports
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 21
    with many other VPN products. • Supports 3DES encryption for maximum security. • VPN Wizard based on VPNC recommended settings. Auto Sensing and Auto Uplink™ LAN Ethernet Connections With its internal 4-port 10/100 switch, the DG834G v3 can connect to either a 10 Mbps standard Ethernet network
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 22
    Modem Wireless Router DG834G Content Filtering With its content filtering feature, the DG834G v3 prevents objectionable content from reaching your PCs. The modem router allows you to control access to Internet content by screening for keywords within Web addresses. You can configure the modem router
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 23
    Reference Manual for the ADSL Modem Wireless Router DG834G What's in the Box? The product package should contain the following items: • 54 Mbps ADSL Modem Wireless Router Model DG834G • AC power adapter (varies by region) • Category 5 (Cat 5) Ethernet cable • Telephone cable with RJ-11 connector •
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 24
    Reference Manual for the ADSL Modem Wireless Router DG834G The Router's Front port. Indicates that the Wireless port is initialized. The Wireless Access Point is turned off. The Local port has detected a link with a 100 Mbps device. Data is being transmitted or received at 100 Mbps. The Local port
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 25
    Reference Manual for the ADSL Modem Wireless Router DG834G The Router's Rear Panel The rear panel of the 54 Mbps ADSL Modem Wireless Router Model DG834G (Figure 2-2) contains port connections. 2 4 1 3 5 Figure 2-2 Viewed from left to right, the rear panel contains the following elements: 1. RJ
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 26
    Internet, refer to the ADSL Modem Wirelesss Router Setup Manual on the DG834G ADSL Modem Wireless Router Resource CD or online as shown in the following table. Table 2-2. Language Dutch English French German Italian Spanish Swedish URL http://documentation.netgear.com/dg834g/nld/208-10039-01/ http
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 27
    how to configure the wireless features of your 54 Mbps ADSL Modem Wireless Router Model DG834G. Considerations for a Wireless Network In planning your wireless network, you should consider the level of security required. You should also select the physical placement of your modem router in order
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 28
    Reference Manual for the ADSL Modem Wireless Router DG834G The time it takes to establish a wireless connection can vary depending on both your security settings and placement. WEP connections can take slightly longer to establish. Also, WEP encryption can consume more battery power on a notebook
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 29
    Manual for the ADSL Modem Wireless Router DG834G wireless device driver and software availability may be limited. Understanding Wireless Settings To configure the Wireless interface of your modem router, click the Wireless Settings link in the Setup section of the main menu. The Wireless Settings
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 30
    Reference Manual for the ADSL Modem Wireless Router DG834G The following parameters are in the Wireless Settings menu: • Wireless Network. - Name (SSID). The Service Set ID, also known as the wireless network name. Enter a value of up to 32 alphanumeric characters. The same Name (SSID) must be
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 31
    Modem Wireless Router DG834G - Wireless Isolation. If enabled, Wireless Stations will not be able to communicate with each other or with Stations on the wired network. This feature should normally be disabled. • Wireless Station Access List. - By default, any wireless computer that is configured
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 32
    . The default SSID is Wireless. Note: The SSID of any wireless access adapters must match the SSID you configure in the 54 Mbps ADSL Modem Wireless Router Model DG834G. If they do not match, you will not get a wireless connection to the DG834G v3. 3-6 Wireless Configuration v1.0, January
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 33
    How to Restrict Wireless Access to Your Network By default, any wireless PC that is configured with the correct SSID will be allowed access to your wireless network. For increased security, the 54 Mbps ADSL Modem Wireless Router Model DG834G provides several ways to restrict wireless access to your
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 34
    'see' your DG834G v3. You must configure your wireless devices to match the wireless network name (SSID) you configure in the ADSL Modem Wireless Router. Note: The SSID of any wireless access adapters must match the SSID you configure in the 54 Mbps ADSL Modem Wireless Router Model DG834G. If they
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 35
    Reference Manual for the ADSL Modem Wireless Router DG834G 2. From the Wireless Settings menu, Wireless Station Access List section, click the Setup Access List button to display the list, shown below: Figure 3-4 3. Select the Turn Access Control On check box to enable restricting wireless
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 36
    Reference Manual for the ADSL Modem Wireless Router DG834G You can copy and paste the MAC addresses from the modem router's Attached Devices menu into the MAC Address box of this menu. To do this, configure each wireless computer to obtain a wireless link to the modem router. The computer should
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 37
    Reference Manual for the ADSL Modem Wireless Router DG834G Restricting wireless access prevents intruders from connecting to your network. However, the wireless data transmissions are still vulnerable to snooping. Using the WEP data encryption settings described below will prevent a determined
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 38
    of http://192.168.0.1 with its default user name of admin and default password of password, or using whatever LAN address and password you have set up. 2. Click the Wireless Settings link in the Setup section of the main menu for the DG834G v3 modem router. 3. In the Security Options section, select
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 39
    the one included in Windows XP only allow entry of one key which must match the default key you set in the DG834G v3. 9. Click Apply to save your settings. Note: When configuring the modem router from a wireless computer, if you configure WEP settings, you will lose your wireless connection when you
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 40
    Manual for the ADSL Modem Wireless Router DG834G How to Configure WPA-802.1x Note: Not all wireless adapters support WPA. Consult the product document for your wireless adapter for instructions on configuring WPA settings. To configure WPA-802.1x, follow these steps: 1. Log in at the default
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 41
    . It also describes how to configure Trend Micro Home Network Security. Protecting Access to Your 54 Mbps ADSL Modem Wireless Router Model DG834G For security reasons, the modem router has its own user name and password. Also, after a period of inactivity for a set length of time, the administrator
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 42
    Reference Manual for the ADSL Modem Wireless Router DG834G 2. From the Main Menu of the browser interface, under the Maintenance heading, select Set Password to bring up the menu shown. Figure 4-2 3. To change the password, first enter the old password, and then enter the new password twice. 4.
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 43
    Reference Manual for the ADSL Modem Wireless Router DG834G Configuring Basic Firewall Services Basic firewall services you can configure include access blocking and scheduling of firewall security. These topics are presented below. Blocking Keywords, Sites, and Services The modem router provides a
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 44
    Manual for the ADSL Modem Wireless Router DG834G 2. Select the Block Sites link of the Security menu. Figure 4-3 3. To enable keyword blocking, select one of the following: • Per Schedule-to turn on keyword blocking according to the settings . Up to 32 entries are supported in the Keyword list. 5.
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 45
    Reference Manual for the ADSL Modem Wireless Router DG834G You can specify one trusted user, which is a computer that will be exempt from blocking and logging. Since the trusted user will be identified by an IP address, you should configure that computer with a fixed IP address. 7. Click Apply to
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 46
    Reference Manual for the ADSL Modem Wireless Router DG834G To access the rules configuration of the DG834G v3, click the Firewall Rules link on the main menu, then click Add for either an Outbound or Inbound Service. Figure 4-4 • To edit an existing rule, select its button on the left side of the
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 47
    Reference Manual for the ADSL Modem Wireless Router DG834G Remember that allowing inbound services opens holes in your firewall. Only enable those ports that are necessary for your network. Following are two application examples of inbound rules: Inbound Rule Example: A Local Public Web Server If
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 48
    Reference Manual for the ADSL Modem Wireless Router DG834G • WAN Users-These settings determine which packets are covered by choices are: - Never - no log entries will be made for this service. - Always - any traffic for this service type will be logged. - Match - traffic of this type which matches
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 49
    Reference Manual for the ADSL Modem Wireless Router DG834G Considerations for Inbound Rules If your external Outbound Rules (Service Blocking) The DG834G v3 allows you to block the use of certain Internet services by computers on your network. This is called service blocking or port filtering. You
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 50
    Reference Manual for the ADSL Modem Wireless Router DG834G Outbound Rule Example: Blocking Instant The list already displays many common services, but you are not limited to these choices. Use the Add Custom Service feature to add any additional services or applications that do not already appear
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 51
    Reference Manual for the ADSL Modem Wireless Router DG834G • WAN Users-These settings determine which packets are covered The choices are: - Never - no log entries will be made for this service. - Always - any traffic for this service type will be logged. - Match - traffic of this type that matches
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 52
    Name of admin, default password of password, or using whatever Password and LAN address you have chosen for the modem router. 2. Select the Services link of the Security menu to display the Services menu shown: Figure 4-9 • To create a new Service, click the Add Custom Service button. 4-12 v1
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 53
    Reference Manual for the ADSL Modem Wireless Router DG834G • To edit an existing Service, select its button on the left side of the table and click Edit Service. • To delete an existing Service, select its button on the left side of the table and click Delete Service. 3. Use the page shown below to
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 54
    Reference Manual for the ADSL Modem Wireless Router DG834G 2. Select the Schedule link of the Security menu to display menu shown below. Figure 4-11 3. Select your time zone. This setting will be used for the blocking schedule according to your local time zone and for time-stamping log entries.
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 55
    via home routers. Note: The 54 Mbps ADSL Modem Wireless Router Model DG834G supports Home Network Security. To take advantage of this feature you must register an account with Trend Micro. For more information, refer to the Home Network Security Quick Start Guide on the NETGEAR Resource CD, or to
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 56
    Reference Manual for the ADSL Modem Wireless Router DG834G To begin using Home Network Security, configure the Security Service and Parental Controls menus on your ADSL Modem Wireless Router. Each screen has a GUI button to click that will take you to the Trend Micro Web site to open your Trend
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 57
    Reference Manual for the ADSL Modem Wireless Router DG834G • Enable Trend Micro Security Services. Select this check box and then click Apply to enable the Security Service features on this page (automatic updates and Client Virus Protection Status information). • Automatically check for update
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 58
    Reference Manual for the ADSL Modem Wireless Router DG834G Parental Controls Settings Click Parental Controls under Content Filtering on the Main menu to get the Trend Micro Parental Controls menu shown below: Click this banner to install the Trend Micro dashboard and set up your Trend Micro account
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 59
    Reference Manual for the ADSL Modem Wireless Router DG834G To select custom profile, click Use Custom Settings and then select the check boxes as desired. (For additional choices, click More Categories). • To allow unrestricted Internet access, click No Restrictions. 3. Click Apply. To configure
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 60
    Reference Manual for the ADSL Modem Wireless Router DG834G • To create a custom profile, click Use Custom Settings and then select the check boxes as illegal or questionable access to, or use of, communications equipment and software, or that provide information on how to bypass proxy server features
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 61
    Manual for the ADSL Modem Wireless Router DG834G • Illegal/Questionable: Sites that advocate or advise on performing illegal acts such as service nationality, ethnic origin, and so forth. • Weapons: Sites that sell, review, or describe guns, knives, martial arts devices, and related accessories. Does
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 62
    Reference Manual for the ADSL Modem Wireless Router DG834G 4-22 v1.0, January 2006 Protecting Your Network
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 63
    54 Mbps ADSL Modem Wireless Router Model DG834G. Backing Up, Restoring, or Erasing Your Settings The configuration settings of the ADSL Modem Wireless Router are stored in a configuration file in the modem router. This file can be backed up to your computer, restored, or reverted to factory default
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 64
    the factory default configuration settings without knowing the login password or IP address, you must use the Default Reset button on the rear panel of the modem router. See "The Router's Rear Panel" on page 2-9. Upgrading the Modem Router's Firmware The software of the ADSL Modem Wireless Router is
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 65
    Manual for the ADSL Modem Wireless Router DG834G How to Upgrade the Modem Router Firmware NETGEAR recommends that you back up your configuration before doing a firmware upgrade. After the upgrade is complete, you may need to restore your configuration settings. 1. Download and unzip the new software
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 66
    Reference Manual for the ADSL Modem Wireless Router DG834G Network Management Information The DG834G v3 provides a variety of status and usage information which is discussed below. Viewing Modem Router Status and Usage Statistics From the Main Menu, under Maintenance, click Modem Router Status to
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 67
    Reference Manual for the ADSL Modem Wireless Router DG834G This screen shows the following parameters: Table 5-1. Menu 3.2 - Modem Router Status Fields Field Account Name Firmware Version ADSL Port MAC Address IP Address Network Type IP Subnet Mask Domain Name Server (DNS) LAN Port MAC Address IP
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 68
    Point feature is disabled or not. If not enabled, the Wireless LED on the front panel will be off. Indicates if the DG834G v3 is configured to broadcast its SSID. Click the Show Statistics button to display modem router usage statistics, as shown below: Figure 5-4 5-6 v1.0, January 2006 Managing
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 69
    Reference Manual for the ADSL Modem Wireless Router DG834G This screen shows the following statistics: Table 5-2. Router Statistics Fields Field Description WAN or LAN Port The statistics for the WAN (Internet) and LAN ports. Status The link status of the port. TxPkts The number of packets
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 70
    Reference Manual for the ADSL Modem Wireless Router DG834G Click the Connection Status button to display modem router connection status, shown below: Figure 5-5 This screen shows the following statistics: Table 5-3. Connection Status Fields for PPPoA Field Connection Time Connecting to Sender
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 71
    Manual for the ADSL Modem Wireless Router DG834G Viewing Attached Devices The Attached Devices menu contains a table of all IP devices that the modem router and Saving Logged Information The modem router will log security-related events such as denied incoming service requests, hacker probes, and
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 72
    Reference Manual for the ADSL Modem Wireless Router DG834G An example of the logs file is shown below. Figure 5-7 5-10 v1.0, January 2006 Managing Your Network
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 73
    Manual for the ADSL Modem Wireless Router DG834G Log address of the initiating device for this log entry. Source port and The service port number of the initiating device, and whether it interface originated settings. Clear the current settings. Managing Your Network v1.0, January 2006 5-11
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 74
    Manual for the ADSL Modem Wireless Router DG834G of the modem router • Modem Router operation (start up, get time, etc.) • Known DoS attacks and Port Scans Saving Activation and Administration Tue, 2002-05-21 18:48:39 - NETGEAR activated [This entry indicates a power-up or reboot with initial time
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 75
    Reference Manual for the ADSL Modem Wireless Router DG834G Dropped Packets Wed, 2002-05-22 07:15:15 - TCP packet dropped - Source:64.12.47.28,4787,WAN Destination:134.177.0.11,21,LAN - [Inbound Default rule match] Sun, 2002-05-22 12:50:33 - UDP packet dropped - Source:64.12.47.28,10714,WAN
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 76
    Reference Manual for the ADSL Modem Wireless Router DG834G • Turn e-mail notification on. Select this check box if you want to receive e-mail logs and alerts from the modem router. • Send alerts and logs via email. - Send To This E-mail Address Enter the e-mail address where you want to send the
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 77
    Reference Manual for the ADSL Modem Wireless Router DG834G Running Diagnostic Utilities and Rebooting the Modem Router The ADSL Modem Wireless Router has a diagnostics feature. You can use the diagnostics menu to perform the following functions from the modem router: • Ping an IP Address to test
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 78
    allow a user or users on the Internet to configure, upgrade and check the status of your 54 Mbps ADSL Modem Wireless Router Model DG834G. Tip: Be sure to change the modem router's default password to a very secure password. The ideal password should contain no dictionary words from any language, and
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 79
    a custom port by entering that number in the box provided. Choose a number between 1024 and 65535, but do not use the number of any common service port. The default is 8080, which is a common alternate for HTTP. 6. Click Apply to have your changes take effect. When accessing your modem router from
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 80
    Reference Manual for the ADSL Modem Wireless Router DG834G 5-18 v1.0, January 2006 Managing Your Network
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 81
    of your 54 Mbps ADSL Modem Wireless Router Model DG834G. Configuring Advanced Security The 54 Mbps ADSL Modem Wireless Router Model DG834G provides a variety of advanced features, such as: • Setting up a Demilitarized Zone (DMZ) Server • Connecting Automatically, as Required • Disabling Port Scan
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 82
    discarded by the modem router unless the traffic is a response to one of your local computers or a service that you have configured in the Ports menu. Instead of discarding this traffic, you can have it forwarded to one computer on your network. This computer is called the Default DMZ Server. How
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 83
    Reference Manual for the ADSL Modem Wireless Router DG834G 2. From the Main Menu, under Advanced, click the WAN Setup link to view the page shown: Figure 6-1 3. Select the Default DMZ Server check box. 4. Type the IP address for that server. 5. Click Apply to save your changes. Connect
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 84
    it is necessary for your ISP connection. Configuring LAN IP Settings The LAN IP Setup menu allows configuration of LAN IP services such as DHCP and RIP. These features can be found under the Advanced heading in the Main Menu of the browser interface. The modem router is shipped preconfigured to use
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 85
    Reference Manual for the ADSL Modem Wireless Router DG834G These addresses are part of the Internet 6-2 The LAN TCP/IP Setup parameters are: • IP Address This is the LAN IP address of the modem router. Warning: If you change the LAN IP address of the modem router while connected through the browser
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 86
    Manual for the ADSL Modem Wireless Router DG834G • RIP Direction RIP (Router Information Protocol) allows a modem router to exchange routing information with other routers. The RIP Direction selection controls how the Modem Router sends and receives RIP packets. Both is the default. - When set
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 87
    Reference Manual for the ADSL Modem Wireless Router DG834G Specify the pool of IP addresses to be assigned by setting the Starting IP Address and Ending IP Address. These addresses should be part of the same IP address subnet as the router's LAN IP address. Using the default addressing scheme, you
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 88
    Reference Manual for the ADSL Modem Wireless Router DG834G 4. Click Apply to enter the reserved address into the table. Note: The reserved address will not be assigned until the next time the computer contacts the router's DHCP server. Reboot the computer or access its IP configuration and force a
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 89
    Reference Manual for the ADSL Modem Wireless Router DG834G Configuring Dynamic DNS If your network has a permanently assigned IP address, you can register a domain name and have that name linked with your IP address by
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 90
    Reference Manual for the ADSL Modem Wireless Router DG834G 2. From the Main Menu of the browser interface, under Advanced, select Dynamic DNS to display the page below. Figure 6-4 3. Access the Web site of one of the dynamic DNS service providers whose names appear in the 'Service Provider' box,
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 91
    Manual for the ADSL Modem Wireless Router DG834G Using Static Routes Static Routes provide additional routing information to your router. Under normal circumstances, the router has adequate routing information after it has been configured for Internet access, and you do not need to configure
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 92
    Reference Manual for the ADSL Modem Wireless Router DG834G How to Configure Static Routes 1. Log in to the router at its default LAN address of http://192.168.0.1 with its default User Name of admin, default password of password, or using whatever User Name, Password and LAN address you have chosen
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 93
    Reference Manual for the ADSL Modem Wireless Router DG834G d. Select Active to configuration. The default setting for UPnP is enabled. If disabled, the Router will not allow any device to automatically control the resources, such as port forwarding (mapping), of the Router. Advanced Configuration
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 94
    Reference Manual for the ADSL Modem Wireless Router DG834G • Advertisement Period: The Advertisement Period is how often the Router will advertise (broadcast) its UPnP information. This value can range from 1 to 1440 minutes. The default period is for 30 minutes. Shorter durations will ensure that
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 95
    VPN you want to set up, along with the VPN Committee (VPNC) recommended default parameters set by the VPN Wizard. • "VPN Tunnel Configuration" on page 7-6 summarizes the three ways to configure a VPN tunnel: VPN Wizard (recommended for most situations), Auto Policy, and Manual Policy. • "How to Set
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 96
    Manual for the ADSL Modem Wireless Router DG834G Overview of VPN Configuration Two common scenarios for configuring VPN tunnels are between a remote personal computer and a network gateway and between two or more network gateways. The DG834G v3 supports both of these types of VPN configurations
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 97
    more NETGEAR VPN-enabled routers is a good way to connect branch or home offices and business partners over the Internet. VPN tunnels also enable access to network resources across the Internet. In this case, use DG834G v3s on each end of the tunnel to form the VPN tunnel end points. See "How to Set
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 98
    Reference Manual for the ADSL Modem Wireless Router DG834G Planning a VPN When you set up a VPN, it is helpful to plan the network configuration and record the configuration parameters on a worksheet: Table 7-1. VPN Tunnel Configuration Worksheet Connection Name: Pre-Shared Key: Secure
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 99
    Reference Manual for the ADSL Modem Wireless Router DG834G • Will the configure your VPN tunnels? - The VPN Wizard using VPNC defaults (see Table 7-2) - The typical automated Internet Key Exchange (IKE) setup (see "Using Auto Policy to Configure VPN Tunnels" on page 7-38) - A Manual Keying setup
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 100
    Reference Manual for the ADSL Modem Wireless Router DG834G VPN Tunnel Configuration There are two tunnel configurations and three ways to configure them: • Use the VPN Wizard to configure a VPN tunnel (recommended for most situations): - See "How to Set Up a Client-to-Gateway VPN Configuration" on
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 101
    Reference Manual for the ADSL Modem Wireless Router DG834G How to Set Up a Client-to-Gateway VPN Configuration 22.23.24.25 DG834G VPN Tunnel 0.0.0.0 192.168.3.1 PCs Figure 7-3 PC (Running NETGEAR ProSafe VPN Client) Setting up a VPN between a remote PC running the NETGEAR ProSafe VPN Client
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 102
    Reference Manual for the ADSL Modem Wireless Router DG834G Table 7-3. VPN Tunnel Configuration Worksheet Connection Name: Pre-Shared Key: Secure Association -- Main Mode or Manual Keys: Perfect Forward Secrecy -- Enabled or Disabled: NETBIOS -- Enabled or Disabled: Encryption Protocol -- DES or
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 103
    Reference Manual for the ADSL Modem Wireless Router DG834G 1. Log in to the DG834G v3 at its LAN address of http://192.168.0.1 with its default user name of admin and password of password. Click the VPN Wizard link in the main menu to display this screen. Click Next to proceed. Figure 7-4 2. Fill
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 104
    Reference Manual for the ADSL Modem Wireless Router DG834G The Summary screen below displays. Figure 7-6 7-10 v1.0, January 2006 Virtual Private Networking
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 105
    Manual for the ADSL Modem Wireless Router DG834G To view the VPNC recommended authentication and encryption settings used by the VPN Wizard, click the "here" link. Click Back to return to the Summary screen. 1 hour Figure 7-7 3. Click Done on the Summary screen to complete the configuration
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 106
    Reference Manual for the ADSL Modem Wireless Router DG834G To view or modify the tunnel settings, select the radio button next to the tunnel entry and click Edit. Note: Refer to "Using Auto Policy to Configure VPN Tunnels" on page 7-38 to enable the IKE keepalive capability on an existing VPN tunnel
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 107
    Modem Wireless Router DG834G b. From the Edit menu of the Security Policy Editor, click Add, then Connection. Figure 7-9 A "New Connection" listing appears in the list of policies. Rename the "New Connection" so that it matches the Connection Name you entered in the VPN Settings of the DG834G v3
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 108
    WAN IP Address of the DG834G v3 in the field directly below the ID Type menu. In this example, 22.23.24.25 would be used. k. The resulting Connection Settings are shown in Figure 7-10. 3. Configure the Security Policy in the NETGEAR ProSafe VPN Client software: a. In the Network Security Policy
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 109
    Reference Manual for the ADSL Modem Wireless Router DG834G a. In the Network Security Policy list on the left side of the Security Policy Editor window, click on My Identity. Figure 7-11 b. Choose None in the Select Certificate menu. c. Select IP Address in the ID Type menu. If you are using a
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 110
    Manual for the ADSL Modem Wireless Router DG834G e. Click the Pre-Shared Key button. In the Pre-Shared Key dialog box, click the Enter Key button. Enter the DG834G v3's Pre-Shared Key and click OK. In this example, 12345678 is entered. This field is case sensitive. Figure 7-12 5. Configure the VPN
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 111
    Reference Manual for the ADSL Modem Wireless Router DG834G c. In the Authentication Method menu, select Pre-Shared key. d. In the Encrypt Alg menu, select the type of encryption to correspond with what was configured for the Encryption Protocol in the DG834G v3 in Table 7-3 on page 7-8. In this
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 112
    Manual for the ADSL Modem Wireless Router DG834G f. In the Hash Alg menu, select SHA-1. g. In the Encapsulation menu, select Tunnel. h. Leave the Authentication Protocol (AH) checkbox unchecked. 7. Save the VPN Client Settings. From the File menu at the top of the Security Policy Editor window
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 113
    the login screen of the Modem Router (unless another PC already has the DG834G v3 management interface open). Information on the progress and status of the VPN client connection can be viewed by opening the NETGEAR ProSafe Log Viewer. To launch this function, click on the Windows Start button, then
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 114
    Manual for the ADSL Modem Wireless Router DG834G 9. The Connection Monitor screen for this connection is shown below: Figure 7-18 In this example you can see the following: • The DG834G v3 has a public IP WAN address of 22.23.24.25. • The DG834G v3 has a LAN IP address of 192.168.3.1. • The VPN
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 115
    Reference Manual for the ADSL Modem Wireless Router DG834G How to Set Up a Gateway-to-Gateway VPN Configuration Note: This section uses the VPN Wizard to set up the VPN tunnel using the VPNC default parameters listed in Table 7-2 on page 7-5. If you have special requirements not covered by these
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 116
    Reference Manual for the ADSL Modem Wireless Router DG834G Table 7-4. VPN Tunnel Configuration Worksheet Connection Name: Pre-Shared Key: Secure Association -- Main Mode or Manual Keys: Perfect Forward Secrecy -- Enabled or Disabled: NETBIOS -- Enabled or Disabled: Encryption Protocol -- DES or
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 117
    Reference Manual for the ADSL Modem Wireless Router DG834G Figure 7-20 2. Fill in the Connection Name and the pre-shared key, select the type of target end point, and click Next to proceed. Enter
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 118
    Manual for the ADSL Modem Wireless Router DG834G 3. Fill in the IP Address or FQDN for the target VPN endpoint WAN connection and click Next. Enter the WAN IP address of the remote VPN tunnel, and click Next. Enter the LAN IP settings of the remote VPN gateway: • IP Address (e.g., 192.168.3.1) •
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 119
    Reference Manual for the ADSL Modem Wireless Router DG834G The Summary screen below displays. Figure 7-24 Virtual Private Networking v1.0, January 2006 7-25
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 120
    Reference Manual for the ADSL Modem Wireless Router DG834G To view the VPNC recommended authentication and encryption settings used by the VPN Wizard, click Summary screen (see Figure 7-24) to complete the configuration procedure. The VPN Settings menu below displays showing that the new tunnel is
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 121
    Reference Manual for the ADSL Modem Wireless Router DG834G Note: Refer to "Using Auto Policy to Configure VPN Tunnels" on page 7-38 to enable the IKE keepalive capability on an existing VPN tunnel. 6. Repeat for the DG834G v3 on LAN B and pay special attention to use the following network settings
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 122
    Reference Manual for the ADSL Modem Wireless Router DG834G a. Open the DG834G v3 management interface and click on VPN Status to get the VPN Status/Log screen (Figure 7-27). Figure 7-27 b. Click on VPN Status (Figure 7-29) to get the Current VPN Tunnels (SAs) screen (Figure 7-28). Click on Connect
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 123
    Manual for the ADSL Modem Wireless Router DG834G VPN Tunnel Control Activating a VPN Tunnel There are three ways to activate a VPN tunnel: • Use the VPN Status page. • Activate the VPN tunnel by pinging the remote endpoint. • Start using the VPN tunnel. Note: Refer to "Using Auto Policy to Configure
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 124
    Reference Manual for the ADSL Modem Wireless Router DG834G 3. Click on VPN Status (Figure 7-29) to get the Current VPN Tunnels (SAs) screen (Figure 7-30). Click on Connect for the VPN tunnel you want to activate. Figure 7-30 Activate the VPN Tunnel by Pinging the Remote Endpoint Note: This section
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 125
    the PC and enter the LAN IP address of the remote DG834G v3. After a short wait, you should see the login screen of the Modem Router (unless another PC already has the DG834G v3 management interface open). • Gateway-to-Gateway Configuration-test the VPN tunnel by pinging the remote network from a PC
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 126
    Reference Manual for the ADSL Modem Wireless Router DG834G b. ping 192.168.3.1. Figure 7-33 Note: The pings may fail the first time. If so, then try the pings a second time. Start Using a VPN Tunnel to Activate It To use a VPN tunnel, use a Web browser to go to a URL whose IP address or range is
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 127
    Manual for the ADSL Modem Wireless Router DG834G Verifying the Status of a VPN Tunnel To use the VPN Status page to determine the status of a VPN tunnel, perform the following steps: 1. Log in to the Modem Router. 2. Open the DG834G v3 management interface and click on VPN Status to get the VPN
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 128
    ADSL Modem Wireless Router DG834G 3. Click on VPN Status (Figure 7-29) to get the Current VPN Tunnels (SAs) screen. Figure 7-35 This table lists the following data for each active VPN Tunnel. • SPI-each SA has a unique SPI (Security Parameter Index) for traffic in each direction. For "Manual" key
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 129
    Reference Manual for the ADSL Modem Wireless Router DG834G Deactivating a VPN Tunnel Sometimes a VPN tunnel must be deactivated for testing purposes. There are two ways to deactivate a VPN tunnel: • Policy table on VPN Policies page • VPN Status page Using the Policy Table on the VPN Policies Page
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 130
    Manual for the ADSL Modem Wireless Router DG834G 2. Open the DG834G v3 management interface and click on VPN Status to get the VPN Status/ Log screen (Figure 7-37). Figure 7-37 3. Click VPN Status (Figure 7-37) to get the Current VPN Tunnels (SAs) screen (Figure 7-38). Click Drop for the VPN
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 131
    Reference Manual for the ADSL Modem Wireless Router DG834G Note: When NETBIOS is enabled (which it is in the VPNC defaults implemented by the VPN Wizard), automatic traffic will reactivate the tunnel. To prevent reactivation from happening, either disable NETBIOS or disable the policy for the tunnel
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 132
    Modem Wireless Router DG834G How to Set Up VPN Tunnels in Special Circumstances When the VPN Wizard and its VPNC defaults (see Table 7-2) are not appropriate for your special circumstances, use one of the following alternatives: • Auto Policy-for a typical automated Internet Key Exchange (IKE) setup
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 133
    Reference Manual for the ADSL Modem Wireless Router DG834G Figure 7-40 Virtual Private Networking v1.0, January 2006 7-39
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 134
    Reference Manual for the ADSL Modem Wireless Router DG834G The DG834G v3 VPN tunnel network connection fields are defined as follows: General. These settings identify this policy and determine its major characteristics. • Policy Name-Enter a unique name to identify this policy. This name is not
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 135
    Reference Manual for the ADSL Modem Wireless Router DG834G Remote LAN. This identifies which PCs on the remote Responder-both incoming and outgoing connections are allowed. Exchange Mode-ensure the remote VPN endpoint is set to use "Main Mode". Diffie-Hellman (DH) Group-the Diffie-Hellman algorithm
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 136
    Manual for the ADSL Modem Wireless Router DG834G Remote Identity Type-select the desired option to match the "Local Identity Type" setting on the remote VPN endpoint. • IP Address-the Internet IP address of the remote VPN endpoint. • Fully Qualified Domain Name-the Domain name of the remote VPN
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 137
    Reference Manual for the ADSL Modem Wireless Router DG834G Example of Using Auto Policy A 14.15.16.17 DG834G VPN Firewall VPN Tunnel 22.23.24.25 B DG834G VPN Firewall 192.168.0.1 192.168.3.1 PCs PCs Figure 7-41 1. Set the LAN IPs on each DG834G v3 to different subnets and configure each
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 138
    Reference Manual for the ADSL Modem Wireless Router DG834G 2. Open the DG834G v3 on LAN A management interface and click on VPN Policies. Figure 7-42 3. Click Add Auto Policy. 4. Enter policy settings (see Figure 7-43). • General - Policy Name = GtoG - Remote VPN Endpoint Address Type = Fixed IP
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 139
    Reference Manual for the ADSL Modem Wireless Router DG834G - Authentication Algorithm = MD5 - Pre-shared Key = 12345678 Figure 7-43 Virtual Private Networking v1.0, January 2006 7-45
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 140
    Reference Manual for the ADSL Modem Wireless Router DG834G 5. Click Apply. The Get VPN Policies web page is displayed. Figure 7-44 6. Repeat for the DG834G v3 on LAN B and pay special attention to use the following network settings as appropriate. • General, Remote Address Data (e.g., 14.15.16.17)
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 141
    Reference Manual for the ADSL Modem Wireless Router DG834G a. Open the DG834G v3 management interface and click on VPN Status to display the VPN Status/Log screen (Figure 7-45). Figure 7-45 b. Click VPN Status (Figure 7-45) to display the Current VPN Tunnels (SAs) screen (Figure 7-46). Click on
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 142
    for the ADSL Modem Wireless Router DG834G Using Manual Policy to Configure VPN Tunnels As an alternative to IKE, you may use Manual Keying, in which you must specify each phase of the connection. A "Manual" VPN policy requires all settings for the VPN tunnel to be manually input at each end (both
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 143
    Manual for the ADSL Modem Wireless Router DG834G General. The DG834G v3 VPN tunnel network connection fields are defined as follows: • Policy Name-enter a unique name to identify this policy. This name is not supplied to the remote VPN the remote LAN. Typically, this setting is used when you wish to
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 144
    Reference Manual for the ADSL Modem Wireless Router DG834G • Subnet address-enter an IP address in the "Single/Start IP address" field, and the desired network mask in the "Subnet Mask" field. The remote VPN endpoint must have these IP addresses entered as its "Local" addresses. ESP Configuration.
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 145
    about troubleshooting your 54 Mbps ADSL Modem Wireless Router Model DG834G. After each problem description, instructions are provided to help you diagnose and solve the problem. For the common problems listed, go to the section indicated. • Is the router on? • Have I connected the router correctly
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 146
    the router's configuration to factory defaults. This will set the router's IP address to 192.168.0.1. This procedure is explained in "Using the Reset button" on page 8-9. If the error persists, you might have a hardware problem and should contact technical support. LAN or Internet Port LEDs Not
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 147
    was changed and you do not know the current IP address, clear the router's configuration to factory defaults. This will set the router's IP address to 192.168.0.1. This procedure is explained in "Using the Reset button" on page 8-9. • Make sure your browser has Java, JavaScript, or ActiveX enabled
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 148
    Reference Manual for the ADSL Modem Wireless Router DG834G If the router does not save changes you have made in the Web Configuration Interface, check the following: • When entering configuration settings, be sure to click the Apply button before moving to another menu or tab, or your changes are
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 149
    Reference Manual for the ADSL Modem Wireless Router DG834G Internet LED Off If the Internet LED is off, disconnect all telephones on the line. If this solves the problem, reconnect the telephones one at a time, being careful to use a microfilter on each telephone. If the microfilters are connected
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 150
    Reference Manual for the ADSL Modem Wireless Router DG834G • If you have selected a login program, you may have incorrectly set the Service Name, User Name and Password. See "Troubleshooting PPPoE or PPPoA", below. • Your ISP may check for your computer's host name. Assign the computer Host Name of
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 151
    Manual for the ADSL Modem Wireless Router DG834G Troubleshooting Internet Browsing If your modem router can Router You can ping the router from your computer to verify that the LAN path to your router is set up correctly. To ping the router from a PC running Windows 95 or later: 1. From the Windows
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 152
    are on for your network interface card and for the hub ports (if any) that are connected to your workstation and router. • Wrong network configuration - Verify that the Ethernet card driver software and TCP/IP software are both installed and configured on your PC or workstation. - Verify that the IP
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 153
    PC. Refer to your ADSL Modem Wirelesss Router Setup Manual (see Table 2-2 on page 2-10). Restoring the Default Configuration and Password This section explains how to restore the factory default configuration settings, changing the router's administration password to password and the IP address to
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 154
    Reference Manual for the ADSL Modem Wireless Router DG834G • Date shown is January 1, 2000 Cause: The router has not yet successfully reached a Network Time Server. Check that your Internet access settings are configured correctly. If you have just completed configuring the router, wait at least
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 155
    specifications for the 54 Mbps ADSL Modem Wireless Router Model DG834G. Network Protocol and Standards Compatibility Data and Routing Protocols: TCP/IP, RIP-1, RIP-2, DHCP, PPPoE or PPPoA, RFC 1483 Bridged or Routed Ethernet, and RFC 1577 Classical IP over ATM Power Adapter North America
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 156
    Reference Manual for the ADSL Modem Wireless Router DG834G A-2 Technical Specifications v1.0, January 2006
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 157
    Appendix B NETGEAR VPN Configuration DG834G v3 to FVL328 This appendix is a case study on how to configure a secure IPSec VPN tunnel from a NETGEAR DG834G v3 to a FVL328. This case study follows the VPN Consortium interoperability profile guidelines (found at http://www.vpnc.org/InteropProfiles/
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 158
    B-1 Note: Product updates are available on the NETGEAR, Inc. web site at http://kbserver.netgear.com/DG834G v3.asp. Step-By-Step Configuration 1. Configure the DG834G v3 as in the Gateway-to-Gateway procedures using the VPN Wizard (see "How to Set Up a Gateway-to-Gateway VPN Configuration" on page
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 159
    Reference Manual for the ADSL Modem Wireless Router DG834G toFVL328 10.5.6.1 172.23.9.1 Click VPN Policies under Advanced - VPN to invoke this screen toFVL328 22.23.24.25 10 5 6 172 23 9 Figure B-2 NETGEAR VPN Configuration B-3 v1.0, January 2006
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 160
    Manual for the ADSL Modem Wireless Router DG834G 2. Configure the FVL328 as in the Gateway-to-Gateway procedures for the VPN Wizard (see "How to Set Up a Gateway-to-Gateway VPN Configuration : • IP Address = 10.5.6.1 • Subnet Mask = 255.255.255.0 B-4 NETGEAR VPN Configuration v1.0, January 2006
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 161
    Reference Manual for the ADSL Modem Wireless Router DG834G toDG834 22.23.24.25 14.15.16.17 Click IKE Policies under VPN to invoke this screen toDG834 22.23.24.25 14.15.16.17 toDG834 172.23.9.1 10.5.6.1 Click VPN Policies under VPN to invoke this screen toDG834 toDG834 14.15.16.17 172 23 9
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 162
    Reference Manual for the ADSL Modem Wireless Router DG834G 3. Test the VPN tunnel by pinging the remote network from a PC attached to the DG834G v3. a. Open the command prompt (Start -> Run -> cmd) b. ping 172.23.9.1 Figure B-4 Note: The pings may fail the first time. If this happens, try the pings
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 163
    Reference Manual for the ADSL Modem Wireless Router DG834G Table B-2. Profile Summary VPN Consortium Scenario: Type of VPN Security Scheme: IP Addressing: NETGEAR-Gateway A NETGEAR-Gateway B Scenario 1 LAN-to-LAN or Gateway-to-Gateway (not PC/Client-to-Gateway) IKE with Preshared Secret/Key (not
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 164
    Reference Manual for the ADSL Modem Wireless Router DG834G The Use of a Fully Qualified Domain Name (FQDN) Many ISPs (Internet Service Providers) provide connectivity to their customers using dynamic instead of static IP addressing. This means that a user's IP address does not remain constant over
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 165
    Reference Manual for the ADSL Modem Wireless Router DG834G 3. On the DG834G v3, configure the Dynamic DNS settings. a. Browse to the Dynamic DNS Setup Screen (see Figure B-6) in the Advanced menu. Figure B-6 b. Configure this screen with appropriate account and hostname settings and then click
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 166
    Reference Manual for the ADSL Modem Wireless Router DG834G 4. On the FVL328, configure the Dynamic DNS settings. Assume a properly configured DynDNS account. a. Browse to the Dynamic DNS Setup Screen (see Figure B-8) in the Advanced menu. Figure B-8 b. Select the DynDNS.org radio button (see Figure
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 167
    Reference Manual for the ADSL Modem Wireless Router DG834G Figure B-9 c. Click Show Status. The resulting screen should show Update OK: good (see Figure B-10). Figure B-10 NETGEAR VPN Configuration v1.0, January 2006 B-11
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 168
    Reference Manual for the ADSL Modem Wireless Router DG834G 5. Configure the DG834G v3 as in the Gateway-to-Gateway procedures using the VPN Wizard (see "How to Set Up a Gateway-to-Gateway VPN Configuration" on page 7-21), being certain to use appropriate network addresses for the environment. The
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 169
    Reference Manual for the ADSL Modem Wireless Router DG834G Figure B-11 Note: The pings may fail the first time. If this happens, try the pings a second time. NETGEAR VPN Configuration v1.0, January 2006 B-13
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 170
    Modem Wireless Router DG834G Configuration Summary (Telecommuter Example) The configuration in this document follows the addressing and configuration mechanics defined by the VPN Consortium. Gather all the necessary information before you begin the configuration process. Verify whether the firmware
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 171
    Reference Manual for the ADSL Modem Wireless Router DG834G • Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC at the Telecommuter's Home Office configures the NETGEAR ProSafe VPN Client endpoint. Step 1: Configuring the Client-to-Gateway VPN Tunnel on the VPN Router at the
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 172
    Reference Manual for the ADSL Modem Wireless Router DG834G fromDG834G (in the example) Dynamic IP address IKE Keep Alive is optional; must match Remote LAN IP Address when enabled (remote PC must respond to
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 173
    Reference Manual for the ADSL Modem Wireless Router DG834G 2. Click Apply when done to get the VPN Policies screen. Figure B-14 To view or modify the tunnel settings, select the radio button next to the tunnel entry and click Edit. NETGEAR VPN Configuration v1.0, January 2006 B-17
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 174
    Reference Manual for the ADSL Modem Wireless Router DG834G Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC at the Telecommuter's Home Office This procedure describes how to configure the 54 Mbps ADSL Modem Wireless Router Model DG834G. We will assume the PC running the client has
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 175
    ADSL Modem Wireless Router DG834G b. From the Edit menu of the Security Policy Editor, click Add, then Connection. A New Connection listing appears in the list of policies. Rename the New Connection so that it matches the Connection Name you entered in the VPN Settings of the DG834G v3 on Gateway
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 176
    Gateway Hostname and enter ntgr.dyndns.org (in this example). k. The resulting Connection Settings are shown in Figure B-16. 3. Configure the Security Policy in the 54 Mbps ADSL Modem Wireless Router Model DG834G software. a. In the Network Security Policy list, expand the new connection by double
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 177
    Reference Manual for the ADSL Modem Wireless Router DG834G b. Click on the Security Policy subheading to show the Security Policy menu. Figure B-17 c. Select the Main Mode in the Select Phase 1 Negotiation Mode check box. 4. Configure the VPN Client Identity. In this step, you will provide
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 178
    Reference Manual for the ADSL Modem Wireless Router DG834G a. In the Network Security Policy list on the left side of the Security Policy Editor window, click My Identity. Figure B-18 b. Choose None in the Select example) in the IP Addr box. B-22 v1.0, January 2006 NETGEAR VPN Configuration
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 179
    Manual for the ADSL Modem Wireless Router DG834G e. Click the Pre-Shared Key button. Figure B-19 f. In the Pre-Shared Key dialog box, click the Enter Key button. Enter the DG834G v3's Pre-Shared Key and click OK. In this example, 12345678 is entered. This field is case sensitive. 5. Configure
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 180
    Reference Manual for the ADSL Modem Wireless Router DG834G Figure B-20 c. In the Authentication Method menu, select Pre-Shared key. d. In the Encrypt Alg menu, select the type of encryption. In this example, use
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 181
    Policy Editor window, select Save. After you have configured and saved the VPN client information, your PC will automatically open the VPN connection when you attempt to access any IP addresses in the range of the remote VPN router's LAN. 8. Check the VPN Connection. NETGEAR VPN Configuration v1
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 182
    to open the My Connections list. c. Choose toDG834G. The 54 Mbps ADSL Modem Wireless Router Model DG834G will report the results of the attempt to connect. Once the from the PC. b. On the Windows taskbar, click the Start button, and then click Run. B-26 v1.0, January 2006 NETGEAR VPN Configuration
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 183
    Reference Manual for the ADSL Modem Wireless Router DG834G c. Type ping -t 192.168.0.1, and then click OK. Figure B-23 This will cause a continuous ping to be sent to the VPN router. After between several seconds and two minutes, the ping response should change from timed out to reply. Figure B-24
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 184
    on the progress and status of the VPN client connection, open the 54 Mbps ADSL Modem Wireless Router Model DG834G Log Viewer. 1. To launch this function, click on the Windows Start button, then select Programs, then 54 Mbps ADSL Modem Wireless Router Model DG834G, then Log Viewer. Note: Use the
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 185
    Reference Manual for the ADSL Modem Wireless Router DG834G While the connection is being established, the Connection Name field in this menu will show SA before the name of the connection. When the connection
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 186
    Reference Manual for the ADSL Modem Wireless Router DG834G 2. To view the VPN tunnels status, click the VPN Status link on the right side of the main menu. Figure B-27 B-30 v1.0, January 2006 NETGEAR VPN Configuration
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 187
    Reference Manual for the ADSL Modem Wireless Router DG834G NETGEAR VPN Configuration v1.0, January 2006 B-31
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 188
    Reference Manual for the ADSL Modem Wireless Router DG834G B-32 v1.0, January 2006 NETGEAR VPN Configuration
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 189
    /index.htm Addressing Wireless Communications http://documentation.netgear.com/reference/enu/wireless/index.htm Preparing a Computer for Network Access http://documentation.netgear.com/reference/enu/wsdhcp/index.htm Virtual Private Networking (VPN) http://documentation.netgear.com/reference/enu
  • Netgear DG834Gv3 | DG834Gv3 Reference Manual - Page 190
    Reference Manual for the ADSL Modem Wireless Router DG834G C-2 Related Documents v1.0, January 2006
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
202-10155-01
January 2006
NETGEAR
, Inc.
4500 Great America Parkway
Santa Clara, CA 95054 USA
Reference Manual for the
ADSL Modem Wireless
Router DG834G