Netgear FS728TPv1 Shared access to the Internet for multiple VLANs - No routin
Netgear FS728TPv1 - ProSafe 24 Port 10/100 Smart Switch Manual
 |
View all Netgear FS728TPv1 manuals
Add to My Manuals
Save this manual to your list of manuals |
Netgear FS728TPv1 manual content summary:
- Netgear FS728TPv1 | Shared access to the Internet for multiple VLANs - No routin - Page 1
using MultiHoming This document describes how to obtain Internet access on multiple VLANs using one Internet gateway capable of managing multiple IP subnets (Multi-homing). The procedure described can apply to all the Smart Switches and VPN Firewall with new Web Interface (defined as the one with - Netgear FS728TPv1 | Shared access to the Internet for multiple VLANs - No routin - Page 2
allow traffic between VLAN a device working at protocol level (Layer 3) is required 24 Port 10/100/1000 Mbps Smart Switch 1 3 5 7 9 11 13 15 17 19 21 23 LINK/ACT SPD Green = 100Mbps Yellow = 10Mbps FD X 2 4 6 8 10 12 14 16 18 20 22 24 LINK/ACT SPD FD X Reset PWR 1 3 5 7 9 11 2 4 6 8 10 - Netgear FS728TPv1 | Shared access to the Internet for multiple VLANs - No routin - Page 3
3.1.0.1 2x Windows XP Computers (2 on each VLAN) 1 x DGFV338 Prosafe Firewall Router (Router firmware 3.4.0.19) Logical Setup GS724TS: Management IP on VLAN1 (192.168.0.239) DGFV338 : Primary range 192.168.0.1/24 (DHCP enabled) Seconday range 172.16.0.1/24 (DHCP not enabled) PC1 - VLAN20 - 192 - Netgear FS728TPv1 | Shared access to the Internet for multiple VLANs - No routin - Page 4
DGFV338 Primary LAN The Primary LAN settings can be defined on the GUI of the DGFV338 (Network Configuration, LAN Setup). If DHCP is required ensure that the correct Starting IP address and Ending IP address are configured including the DNSs settings. - Netgear FS728TPv1 | Shared access to the Internet for multiple VLANs - No routin - Page 5
LAN to the DGFV338 the Multi-homing option should be used. This can be accessed via the GUI (Network configuration, LAN Setup, Multi-Homing) PCs with an IP address within this range will need the IP address, Default Gateway and DNS servers (if different from the Default Gateway) manually set. - Netgear FS728TPv1 | Shared access to the Internet for multiple VLANs - No routin - Page 6
are created on the Smartswitch via the GUI (Switching, VLAN, Basic, VLAN configuration). To complete the scenarion 3 VLAN will need to be created. The two pictures below show the creation of VLAN20, and the results of the creation of all the VLAN required to complete the scenario (VLAN20, 30, 40 - Netgear FS728TPv1 | Shared access to the Internet for multiple VLANs - No routin - Page 7
Assigning Port membership to a VLAN Port membership can be assigned via the GUI (Switching, VLAN, Advanced , VLAN membership). Three options are available: - No membership (no simbol appearing in the gray box underneath the port number) - Untagged membership (U) - Tagged membership (T) In order to - Netgear FS728TPv1 | Shared access to the Internet for multiple VLANs - No routin - Page 8
Assigning a PVID to a port The PVID (Port VLAN ID) is assigned to each port via the GUI (Switching, VLAN, Advanced, Port PVID configuration). It is important that the PVID matches the VLAN a port is member of, unless such port belongs to multiple VLANs (in which case the PVID must still be set and - Netgear FS728TPv1 | Shared access to the Internet for multiple VLANs - No routin - Page 9
- Netgear FS728TPv1 | Shared access to the Internet for multiple VLANs - No routin - Page 10
16.0/0/24 range to port 0/7 or 0/8 - Connect the Prosafe firewall to port 0/9 It should now be possible for each PC to ping the IP address of the Prosafe Firewall within the same IP subnet, and also connect to the Internet (assuming the DNS settings are correctly set via DHCP or manual configuration
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
 |
 |
GS700TS FS700TS – Access to the Internet on multiple VLANS using Multi-
Homing
This document describes how to obtain Internet access on multiple VLANs using one Internet
gateway capable of managing multiple IP subnets (Multi-homing).
The procedure described can apply to all the Smart Switches and VPN Firewall with new Web
Interface (defined as the one with the Menus appearing horizontally on top).
Table of Contents
VLAN-Definition
...........................................................................................................................
2
Notes when setting-up VLANs
.....................................................................................................
2
Multi-Homing (extract from the DGFV338 Help page)
..................................................................
3
Physical Setup
............................................................................................................................
3
Logical Setup
..............................................................................................................................
3
DGFV338 Primary LAN
...............................................................................................................
4
DGFV338 Secondary VLAN
........................................................................................................
5
Smartswitch VLAN creation
.........................................................................................................
6
Assigning Port membership to a VLAN
........................................................................................
7
Assigning a PVID to a port
...........................................................................................................
8
Testing the scenario
..................................................................................................................
10
Further notes
.............................................................................................................................
10