Netgear GS308EP Installation Guide
Netgear GS308EP Manual
 |
View all Netgear GS308EP manuals
Add to My Manuals
Save this manual to your list of manuals |
Netgear GS308EP manual content summary:
- Netgear GS308EP | Installation Guide - Page 1
Installation Guide 8-Port Gigabit Ethernet Smart Managed Plus Switch with PoE+ (62W) GS308EP 8-Port Gigabit Ethernet Smart Managed Plus Switch with High-Power PoE+ (123W) GS308EPP Package contents • NETGEAR Smart Managed Plus Switch • Power adapter • Detachable power cable (varies by region) • Wall - Netgear GS308EP | Installation Guide - Page 2
power from the switch, consider using a shorter cable. September 2020 © NETGEAR, Inc., NETGEAR and the NETGEAR Logo are trademarks of NETGEAR, Inc. Any non‑NETGEAR trademarks are used for reference purposes only. PoE troubleshooting Here are some tips for correcting PoE problems that might occur
-
1 -
2
 |
 |
Installation Guide
1. Register with the NETGEAR Insight app
1.
Search for
NETGEAR Insight
and download the latest app.
2.
Set up a NETGEAR account if you do not have one.
3.
Tap the menu in the upper left corner.
4.
Tap
REGISTER ANY NETGEAR DEVICE
.
5.
Enter the serial number located on the bottom of the switch, or use the
camera on your mobile device to scan the serial number bar code.
6.
Tap
GO
.
The switch is registered and added to your account. You can now view the
switch in the NETGEAR Insight app.
8-Port Gigabit Ethernet Smart Managed Plus
Switch with PoE+ (62W)
GS308EP
8-Port Gigabit Ethernet Smart Managed Plus
Switch with High-Power PoE+ (123W)
GS308EPP
Package contents
•
NETGEAR Smart Managed Plus Switch
•
Power adapter
•
Detachable power cable (varies by region)
•
Wall installation kit
•
Rubber feet
•
Installation guide
This switch is designed for indoor use only. If you want to connect to a device
located outdoors, the outdoor device must be properly grounded and surge
protected, and you must install an Ethernet surge protector inline between the
switch and the outdoor device. Failure to do so can damage the switch.
WARNING:
Before connecting this switch to outdoor cables or devices, see
for safety and warranty information.
3. Check the LEDs
When you connect the power cord to the switch and plug it into an electrical
outlet, the LEDs indicate the status.
LED
Description
Power
Solid green
. The switch is powered on and operating normally.
Off
.
Power is not supplied to the switch.
PoE Max
(The status of
the switch’s PoE
budget)
Off
. Sufficient (more than 7W of) PoE power is available.
Solid yellow
. Less than 7W of PoE power is available.
Blinking yellow
. At least once during the previous two minutes, less
than 7W of PoE power was available.
Left port LED
Solid green
.1000 Mbps link on this port.
Blinking green
. 1000 Mbps activity on this port.
Solid yellow
. 100 Mbps or 10 Mbps link on this port.
Blinking yellow
. 100 Mbps or 10 Mbps activity on this port.
Off
. No link is detected on this port.
Right Port LED
Solid Green
. The port is delivering PoE power.
Off
. The port is not delivering PoE power.
Solid yellow
. A PoE fault occurred.
Continued on the next page
.
Sample connections
2. Connect the switch
Router
Internet
Laptop
PoE VoIP Phone
PoE WiFi access point
GS308EPP switch
Internet
PoE and non-PoE connections
Note:
We recommend that you use a Category 5e (Cat 5e) cable or higher-rated
cable for Gigabit Ethernet connections.