Netgear GS750E Hardware Installation Guide
Netgear GS750E Manual
 |
View all Netgear GS750E manuals
Add to My Manuals
Save this manual to your list of manuals |
Netgear GS750E manual content summary:
- Netgear GS750E | Hardware Installation Guide - Page 1
48-Port Gigabit Ethernet Smart Managed Plus Switch Hardware Installation Guide August 2017 202-11785-02 350 E. Plumeria Drive San Jose, CA 95134 USA - Netgear GS750E | Hardware Installation Guide - Page 2
Managed Plus Switch Support Thank you for purchasing this NETGEAR product. You can visit www.netgear.com/support to register your product, get help, access the latest downloads and user manuals, and join our community. We recommend that you use only official NETGEAR support resources. Conformity For - Netgear GS750E | Hardware Installation Guide - Page 3
Instructions and Warnings 6 Chapter 2 Hardware Overview Front Panel...10 Back Panel...10 LEDs...10 Switch Hardware Interfaces 11 RJ-45 Ports for 10/100/1000M BASE-T Ethernet Connectivity 11 Factory Defaults 5 Troubleshooting Troubleshooting Chart 22 Additional Troubleshooting Suggestions 22 3 - Netgear GS750E | Hardware Installation Guide - Page 4
to the switch and includes the following sections: • Overview • Features • Safety Instructions and Warnings Note For more information about the topics that are covered in this manual, visit the support website at support.netgear.com. Note For technical specifications, see the data sheet at - Netgear GS750E | Hardware Installation Guide - Page 5
bandwidth, Quality of Service (QoS) for prioritizing IP scanner utility. Note The configuration utility runs on Windows-based computers. Visit netgear.com/support the user manual which you can download from downloadcenter.netgear.com. password. • DHCP client. • Includes the following - Netgear GS750E | Hardware Installation Guide - Page 6
with LACP) - IEEE 802.1p Class of Service (QoS and DSCP) - IEEE 802.3az Energy Auto Uplink™ technology is supported on all ports. • Automatic Half-duplex backpressure control. • NETGEAR green power-saving features: - Energy port link is down Safety Instructions and Warnings Use the following safety - Netgear GS750E | Hardware Installation Guide - Page 7
to your NETGEAR product, which might not be covered by NETGEAR's warranty. • Observe and follow service markings: - Do not service any the system gets wet, see the appropriate section in your troubleshooting guide, or contact your trained service provider. • Do not push any objects into the openings - Netgear GS750E | Hardware Installation Guide - Page 8
48-Port Gigabit Ethernet Smart Managed Plus Switch electrical ratings label. The voltage and current rating of the cable must be greater than the ratings marked on the product. • To help prevent electric shock, plug the system and peripheral power cables into properly grounded electrical outlets. • - Netgear GS750E | Hardware Installation Guide - Page 9
Hardware Overview This chapter describes the switch hardware features. The chapter includes the following sections: • Front Panel • Back Panel • LEDs • Switch Hardware Interfaces 2 9 - Netgear GS750E | Hardware Installation Guide - Page 10
Managed Plus Switch Front Panel The GS750E switch provides forty-eight 10/100/1000M BASE-T RJ-45 ports. The following figure shows the front panel. Figure 1. Front panel Number 1 2 3 4 Description Power LED (see LEDs on page 10) Recessed Factory Defaults button Forty-eight independent 10/100 - Netgear GS750E | Hardware Installation Guide - Page 11
ascertains the maximum speed (10 Mbps, 100 Mbps, or 1 Gbps) and duplex mode (half-duplex or full-duplex) of the attached device. All ports support a Category 5e (Cat 5e) cable (or higher rated Ethernet cable) terminated with an 8-pin RJ-45 connector. To simplify the procedure for attaching devices - Netgear GS750E | Hardware Installation Guide - Page 12
settings, causing all custom settings to be erased. To return the switch to its factory default settings: 1. Insert a device such as a straightened paper clip into the opening. 2. Press the recessed Factory Defaults button for more than three seconds. The switch reboots and returns to its factory - Netgear GS750E | Hardware Installation Guide - Page 13
Installation 3 This chapter describes the installation procedures for the switch. Switch installation involves the steps described in the following sections: • Step 1: Prepare the Site • Step 2: Protect Against Electrostatic Discharge • Step 3: Unpack the Switch • Step 4: Install the Switch • - Netgear GS750E | Hardware Installation Guide - Page 14
48-Port Gigabit Ethernet Smart Managed Plus Switch Step 1: Prepare the Site Before you install the switch, make sure that the operating environment meets the site requirements that are listed in the following table. Table 2. Site requirements Characteristics Mounting Access Power source Cabling - Netgear GS750E | Hardware Installation Guide - Page 15
48-Port Gigabit Ethernet Smart Managed Plus Switch • When unpacking a static-sensitive component from its shipping carton, leave it in the antistatic package until you are ready to install it. Just before unwrapping the antistatic package, discharge static electricity from your body. • Before moving - Netgear GS750E | Hardware Installation Guide - Page 16
48-Port Gigabit Ethernet Smart Managed Plus Switch • Rubber footpads for tabletop installation • Installation guide 5. If any item is missing or damaged, contact your local NETGEAR reseller for replacement. Step 4: Install the Switch You can install the switch in a standard 19-inch (48.26-centimeter - Netgear GS750E | Hardware Installation Guide - Page 17
48-Port Gigabit Ethernet Smart Managed Plus Switch 4. Align the mounting holes in the brackets with the holes in the rack, and insert two pan-head screws with nylon washers through each bracket and into the rack. 5. Tighten the screws with a No. 2 Phillips screwdriver to secure mounting brackets to - Netgear GS750E | Hardware Installation Guide - Page 18
48-Port Gigabit Ethernet Smart Managed Plus Switch Note Contact your NETGEAR reseller to purchase these modules. If you do not want to install an SFP module, skip this procedure. To install an SFP transceiver module: 1. Insert - Netgear GS750E | Hardware Installation Guide - Page 19
computer) for very basic setup. For more information about managing the switch, see the installation guide and the user manual, which you can download from downloadcenter.netgear.com. Note The switch's default IP address is 192.168.0.239 and its default subnet mask is 255.255.255.0. Installation 19 - Netgear GS750E | Hardware Installation Guide - Page 20
Desktop Switching 4 The switch is designed to provide flexibility in configuring network connections. The switch can be used as your only network traffic-distribution device or with 10 Mbps, 100 Mbps, and 1 Gbps hubs, routers, and switches. You can use the switch as a desktop switch to build a - Netgear GS750E | Hardware Installation Guide - Page 21
Troubleshooting 5 This chapter provides information about troubleshooting the switch. The chapter includes the following sections: • Troubleshooting Chart • Additional Troubleshooting Suggestions 21 - Netgear GS750E | Hardware Installation Guide - Page 22
interface, you can configure loop prevention to prevent network loops. Additional Troubleshooting Suggestions If the suggestions in the troubleshooting chart do not resolve the problem, see the following troubleshooting suggestions: • Network adapter cards. Make sure that the network adapters that - Netgear GS750E | Hardware Installation Guide - Page 23
the integrity of the switch by resetting it. To reset the switch, disconnect the AC power from the switch and then reconnect the AC power. If the problem continues, contact NETGEAR technical support. For more information, visit the support website at support.netgear.com. • Autonegotiation. The RJ-45
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
 |
 |
48-Port Gigabit Ethernet Smart
Managed Plus Switch
Hardware Installation Guide
August 2017
202-11785-02
350 E. Plumeria Drive
San Jose, CA 95134
USA