Netgear GSM7248R GSM7248R Hardware manual
Netgear GSM7248R - ProSafe Switch Manual
 |
UPC - 606449054743
View all Netgear GSM7248R manuals
Add to My Manuals
Save this manual to your list of manuals |
Netgear GSM7248R manual content summary:
- Netgear GSM7248R | GSM7248R Hardware manual - Page 1
Managed Layer 2 Switches GSM7224R and GSM7248R Hardware Installation Guide NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA 202-10351-01 November 2007 - Netgear GSM7248R | GSM7248R Hardware manual - Page 2
may, however, be subject to certain restrictions. Please refer to the notes in the operating instructions. It is hereby certified that the NETGEAR ProSafe™ 48-Port L2 Managed Switch with Static Routing GSM7248R has been suppressed in accordance with the conditions set out in the BMPT-AmtsblVfg 243 - Netgear GSM7248R | GSM7248R Hardware manual - Page 3
Static Routing GSM7224R) does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications. This digital apparatus (NETGEAR ProSafe™ 48-Port L2 Managed Switch with Static Routing GSM7248R - Netgear GSM7248R | GSM7248R Hardware manual - Page 4
is to certify that the NETGEAR ProSafe™ 48-Port L2 Managed Switch with Static Routing GSM7248R is shielded against the GSM7224R and GSM7248R November 2007 managed switch ProSafe™ 24-Port L2 Managed Switch with Static Routing GSM7224R ProSafe™ 48-Port L2 Managed Switch with Static Routing GSM7248R - Netgear GSM7248R | GSM7248R Hardware manual - Page 5
i How to Use This Manual ii How to Print This Manual ii Chapter 1 Introduction GSM7224R Front Panel and LEDs 1-1 GSM7224R Rear Panel 1-2 GSM7248R Front Panel and LEDs 1-2 GSM7248R Rear Panel 1-3 Interpreting the LEDs ...1-3 Safety Instructions ...1-4 Chapter 2 Hardware Installation Package - Netgear GSM7248R | GSM7248R Hardware manual - Page 6
Chapter 3 Troubleshooting Troubleshooting Chart 3-1 Additional Troubleshooting Suggestions 3-2 Appendix A Default Settings and Technical Specifications Default Settings ...A-1 Technical Specifications A-3 Appendix B Related Documents vi v1.0, November 2007 - Netgear GSM7248R | GSM7248R Hardware manual - Page 7
This Manual The NETGEAR® Managed Layer 2 Switches GSM7224R and GSM7248R Hardware Installation Guide describes how to install, configure, and troubleshoot the ProSafe™ 24-Port L2 Managed Switch with Static Routing GSM7224R and the ProSafe™ 48-Port L2 Managed Switch with Static Routing GSM7248R. The - Netgear GSM7248R | GSM7248R Hardware manual - Page 8
24-Port L2 Managed Switch with Static Routing GSM7224R ProSafe™ 48-Port L2 Managed Switch with Static Routing GSM7248R November 2007 For more information about network, Internet, firewall, and VPN technologies, see the links to the NETGEAR website in Appendix B, "Related Documents". Note: Product - Netgear GSM7248R | GSM7248R Hardware manual - Page 9
2 Switches GSM7224R and GSM7248R Hardware Installation Guide • Printing from PDF. Your computer must have the free Adobe Acrobat Reader installed in order to view and print PDF files. The Acrobat reader is available on the Adobe website at http://www.adobe.com. - Printing a PDF chapter. Use the PDF - Netgear GSM7248R | GSM7248R Hardware manual - Page 10
Managed Layer 2 Switches GSM7224R and GSM7248R Hardware Installation Guide iv v1.0, November 2007 - Netgear GSM7248R | GSM7248R Hardware manual - Page 11
boost performance, and increase productivity. This guide describes hardware installation and basic troubleshooting for the ProSafe™ 24-Port L2 Managed Switch with Static Routing GSM7224R and ProSafe™ 48-Port L2 Managed Switch with Static Routing GSM7248R. These switches can be free standing, or rack - Netgear GSM7248R | GSM7248R Hardware manual - Page 12
2 Switches GSM7224R and GSM7248R Hardware Installation Guide GSM7224R Rear Panel The rear panel has a console port, a redundant power supply connector, and a standard AC power receptacle for the supplied power cord. Console Figure 1-2 Redundant power supply connector Power receptacle GSM7248R - Netgear GSM7248R | GSM7248R Hardware manual - Page 13
Managed Layer 2 Switches GSM7224R and GSM7248R Hardware Installation Guide GSM7248R Rear Panel The rear panel has a console port, a Power receptacle The following table describes the LEDs on the front panel of the switch. Table 1-1. LED Descriptions LED PWR (power) FAN RPS (redundant power supply - Netgear GSM7248R | GSM7248R Hardware manual - Page 14
2 Switches GSM7224R and GSM7248R Hardware Installation Guide Table the GSM7224R or port 45-48 media for GSM7248R is changed to copper, the SFP LEDs change to Off status. Safety Instructions follow service markings. - Do not service any product except as explained in your system documentation. - - Netgear GSM7248R | GSM7248R Hardware manual - Page 15
Managed Layer 2 Switches GSM7224R and GSM7248R Hardware Installation Guide - The product does not operate correctly when you follow the operating instructions. • Keep your system away from radiators and heat sources. Also, do not block cooling vents. • Do not spill food or liquids on your system - Netgear GSM7248R | GSM7248R Hardware manual - Page 16
2 Switches GSM7224R and GSM7248R Hardware Installation Guide • To help protect your system from sudden, transient increases and decreases in electrical power, use a surge suppressor, line conditioner, or uninterruptible power supply (UPS). • Position system cables and power cables carefully; route - Netgear GSM7248R | GSM7248R Hardware manual - Page 17
- Configuration software - Documentation including the Managed Layer 2 Switches 7200R Series CLI Reference Manual Version 7.0, the NETGEAR 7000 Series Managed Switch Administration Guide Version 6.0, the NETGEAR Installation Guide 7000 Series Managed Switch (7200R, 7300S), and this guide • Warranty - Netgear GSM7248R | GSM7248R Hardware manual - Page 18
Managed Layer 2 Switches GSM7224R and GSM7248R Hardware Installation Guide Protecting Against Electrostatic Discharge Warning: 2-1. Note: If any item is found missing or damaged, contact your local NETGEAR reseller for replacement. 5. Inspect the products and accessories for damage. Report any - Netgear GSM7248R | GSM7248R Hardware manual - Page 19
Managed Layer 2 Switches GSM7224R and GSM7248R Hardware Installation Guide Installation Install the equipment in the following sequence, as presented in this chapter: 1. Select a location. See the following section, "Selecting a Location." 2. Install the switch. See "Installing the Switch" on page - Netgear GSM7248R | GSM7248R Hardware manual - Page 20
Switches GSM7224R and GSM7248R Hardware Installation Guide Table 2-1. Site Requirements for Switch Location (continued) Requirements Ventilation Cabling Do not restrict airflow by covering or obstructing air inlets on the sides of the switch you will install the switch. Route the cable to avoid - Netgear GSM7248R | GSM7248R Hardware manual - Page 21
Managed Layer 2 Switches GSM7224R and GSM7248R Hardware Installation Guide 3. Tighten the screws with a No. 1 Phillips screwdriver to secure each bracket. 4. Align the bracket and rack holes. Use two pan-head screws with nylon washers - Netgear GSM7248R | GSM7248R Hardware manual - Page 22
Managed Layer 2 Switches GSM7224R and GSM7248R Hardware Installation Guide SFP Modules The module bay accommodates a module seats into the connector. Figure 2-2 Connecting a Redundant Power Supply (RPS) Each switch has a redundant power supply (RPS) connector and a power receptacle on the rear. - Netgear GSM7248R | GSM7248R Hardware manual - Page 23
Layer 2 Switches GSM7224R and GSM7248R Hardware Installation Guide You can connect an external DC-to-DC power supply unit to the switch to provide redundant power in case the primary power supply fails. To connect a redundant power supply (RPS) unit to the switch, first turn off the switch. When - Netgear GSM7248R | GSM7248R Hardware manual - Page 24
document and in PDF format on the Resource CD). • Managed Layer 2 Switches 7200R Series CLI Reference Manual Version 7.0. Gives detailed examples of how to use the CLI, and is located on the Resource CD. • NETGEAR 7000 Series Managed Switch Administration Guide Version 6.0. Describes configuration - Netgear GSM7248R | GSM7248R Hardware manual - Page 25
, and solutions of possible problems. Table 3-1. Troubleshooting Chart Problem Power LED is off. Cause No power is received Link LED is off or intermittent. Port connection is not working. Solution Check the power cord connections for the switch at the switch and the connected device. Make - Netgear GSM7248R | GSM7248R Hardware manual - Page 26
Managed Layer 2 Switches GSM7224R and GSM7248R Hardware Installation Guide Table 3-1. Troubleshooting Chart (continued) Problem Cause Solution A segment or device is not recognized as part of the network. One or more devices are not Verify that the cabling is correct. - Netgear GSM7248R | GSM7248R Hardware manual - Page 27
Routing GSM7224R and ProSafe™ 48-Port L2 Managed Switch with Static Routing GSM7248R. Default Settings The following table lists the factory default settings for the switches. You can use the RST (reset) button to return a switch to its factory default settings. Table A-1. Default Configuration - Netgear GSM7248R | GSM7248R Hardware manual - Page 28
2 Switches GSM7224R and GSM7248R Hardware Installation Guide Table A-1. Default Configuration Settings (continued) Features Admin edge port Link aggregation Port mirroring Traffic prioritization ACL GVRP GMRP IP routing MAC address aging SNMP community VLAN Ingress filtering GSM7224R Default - Netgear GSM7248R | GSM7248R Hardware manual - Page 29
1Q Static VLAN (Up to 4k) • 802.1p Class of Service (CoS) • 802.1D Spanning Tree Protocol (STP) • 802.1w Rapid Spanning Tree Protocol (RSTP) • 802.1s Multiple Spanning Tree Protocol (MSTP) • 802.3ad Link Aggregation (LACP) • IGMP v1, v2 Snooping Support Default Settings and Technical Specifications - Netgear GSM7248R | GSM7248R Hardware manual - Page 30
Managed Layer 2 Switches GSM7224R and GSM7248R Hardware Installation Guide Table A-2. Technical Specifications (continued) Feature GSM7224R GSM7248R Layer 3 services • Static routing • ACL • DiffServ QOS • DHCP, BOOTP Relay • DHCP server • UDP Relay • ARP • IGMP querier • Static routing • ACL - Netgear GSM7248R | GSM7248R Hardware manual - Page 31
Managed Layer 2 Switches GSM7224R and GSM7248R Hardware Installation Guide Table A-2. Technical Specifications (continued) Feature GSM7224R Environment Operating: • 22.2 #950) • UL listed (UL 1950)/cUL IEC950/ EN60950 Default Settings and Technical Specifications A-5 v1.0, November 2007 - Netgear GSM7248R | GSM7248R Hardware manual - Page 32
Managed Layer 2 Switches GSM7224R and GSM7248R Hardware Installation Guide A-6 Default Settings and Technical Specifications v1.0, November 2007 - Netgear GSM7248R | GSM7248R Hardware manual - Page 33
and Vista Wireless http://documentation.netgear.com/reference/enu/winzerocfg/index.htm Configuration Utilities Internet Networking and TCP/IP http://documentation.netgear.com/reference/enu/tcpip/index.htm Addressing Wireless Communications http://documentation.netgear.com/reference/enu/wireless - Netgear GSM7248R | GSM7248R Hardware manual - Page 34
Managed Layer 2 Switches GSM7224R and GSM7248R Hardware Installation Guide B-2 Related Documents v1.0, November 2007
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
 |
 |
202-10351-01
November 2007
NETGEAR
, Inc.
4500 Great America Parkway
Santa Clara, CA 95054 USA
Managed Layer 2
Switches GSM7224R
and GSM7248R
Hardware Installation
Guide