Netgear GSM7248v2 GSM72XXv2 Hardware Installation Guide
Netgear GSM7248v2 - ProSafe 48 Port Layer 2 Gigabit L2 Ethernet Switch Manual
 |
View all Netgear GSM7248v2 manuals
Add to My Manuals
Save this manual to your list of manuals |
Netgear GSM7248v2 manual content summary:
- Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 1
Managed Layer 2 Switches GSM7224 and GSM7248 Hardware Installation Guide NETGEAR, Inc. 350 E. Plumeria Drive Sant Jose, CA 95134 USA 202-10351-02 July 2009 - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 2
the product(s) or circuit layout(s) described herein. Certificate of the Manufacturer/Importer It is hereby certified that the NETGEAR ProSafe™ 24-Port L2 Managed Switch with Static Routing GSM7224 has been suppressed in accordance with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 3
, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there 22). This is to certify that the NETGEAR ProSafe™ 24-Port L2 Managed Switch with Static Routing GSM7224 is shielded against the generation of radio interference - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 4
This is to certify that the NETGEAR ProSafe™ 48-Port L2 Managed Switch with Static Routing GSM7248 is shielded against the generation GSM7224 and GSM7248 July 2009 managed switch ProSafe™ 24-Port L2 Managed Switch with Static Routing GSM7224 ProSafe™ 48-Port L2 Managed Switch with Static Routing - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 5
, and Scope vii How to Print This Manual viii Chapter 1 Introduction GSM7224 Front Panel and LEDs 1-1 GSM7224 Rear Panel ...1-2 GSM7248 Front Panel and LEDs 1-2 GSM7248 Rear Panel ...1-3 Interpreting the LEDs ...1-3 Safety Instructions ...1-4 Chapter 2 Hardware Installation Package Contents - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 6
Additional Troubleshooting Suggestions 3-2 Appendix A Default Settings and Technical Specifications Default Settings ...A-1 Technical Specifications A-3 Appendix B Related Documents vi v1.0, July 2009 - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 7
About This Manual The NETGEAR® Managed Layer 2 Switches GSM7224 and GSM7248 Hardware Installation Guide describes how to install, configure, and troubleshoot the ProSafe™ 24-Port L2 Managed Switch with Static Routing GSM7224 and the ProSafe™ 48-Port L2 Managed Switch with Static Routing GSM7248. - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 8
Hardware Installation Guide • Scope. This manual is written for the Managed Layer 2 Switch according to these specifications: Product Version Manual Publication Date ProSafe™ 24-Port L2 Managed Switch with Static Routing GSM7224 ProSafe™ 48-Port L2 Managed Switch with Static Routing GSM7248 July - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 9
Managed Layer 2 Switches GSM7224 and GSM7248 Hardware Installation Guide • Click the print icon in the upper left of your browser window. Tip: If your printer supports printing two pages on a single sheet of paper, you can save paper and printer ink by selecting this feature. ix v1.0, July 2009 - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 10
Managed Layer 2 Switches GSM7224 and GSM7248 Hardware Installation Guide x v1.0, July 2009 - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 11
, boost performance, and increase productivity. This guide describes hardware installation and basic troubleshooting for the ProSafe™ 24-Port L2 Managed Switch with Static Routing GSM7224 and ProSafe™ 48-Port L2 Managed Switch with Static Routing GSM7248. These switches can be free standing, or rack - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 12
Managed Layer 2 Switches GSM7224 and GSM7248 Hardware Installation Guide GSM7224 Rear Panel The rear panel has a console panel contains LEDs, a USB port, a RST (reset) button, RJ-45 jacks, and copper/fiber combo ports. LEDs USB port Reset button Figure 1-3 RJ-45 jacks Copper/fiber combo ports - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 13
Managed Layer 2 Switches GSM7224 and GSM7248 Hardware Installation Guide GSM7248 Rear Panel The rear panel has a console port, a Power receptacle The following table describes the LEDs on the front panel of the switch. Table 1-1. LED Descriptions LED PWR (power) FAN RPS (redundant power supply) - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 14
Switches GSM7224 and GSM7248 Hardware Installation Guide 24 for the GSM7224 or port 45-48 media for GSM7248 is changed to copper, the SFP LEDs change to Off status. Safety Instructions outlet and replace the part, or contact your trained service provider: - The power cable, extension cable, or - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 15
Managed Layer 2 Switches GSM7224 and GSM7248 Hardware Installation Guide - The product does not operate correctly when you follow the operating instructions. • Keep your system away from radiators and heat sources. Also, do not block cooling vents. • Do not spill food or liquids on your system - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 16
2 Switches GSM7224 and GSM7248 Hardware Installation Guide • To help protect your system from sudden, transient increases and decreases in electrical power, use a surge suppressor, line conditioner, or uninterruptible power supply (UPS). • Position system cables and power cables carefully; route - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 17
Documentation including the ProSafe 7200R Managed Switches CLI Reference Manual, the ProSafe 7000 Series Managed Switch Administration Guide, the NETGEAR 7000 Series Managed Switches (7200RS, 7200, 7300S, 726), and this guide • Warranty and Support card • Installation guide • ProSafe NMS100 Network - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 18
Managed Layer 2 Switches GSM7224 and GSM7248 Hardware Installation Guide Protecting Against Electrostatic Discharge Warning: Static 2-1. Note: If any item is found missing or damaged, contact your local NETGEAR reseller for replacement. 5. Inspect the products and accessories for damage. Report any - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 19
Managed Layer 2 Switches GSM7224 and GSM7248 Hardware Installation Guide Installation Install the equipment in the following sequence, as presented in this chapter: 1. Select a location. See the following section, "Selecting a Location." 2. Install the switch. See "Installing the Switch" on page - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 20
Switches GSM7224 and GSM7248 Hardware Installation Guide Table 2-1. Site Requirements for Switch Location (continued) Requirements Ventilation Cabling Do not restrict airflow by covering or obstructing air inlets on the sides of the switch you will install the switch. Route the cable to avoid - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 21
Managed Layer 2 Switches GSM7224 and GSM7248 Hardware Installation Guide 3. Tighten the screws with a No. 1 Phillips the AC power adapter cable to the rear of the switch, and the other end to a grounded three-pronged AC outlet. 2. Check the Power LED on the front panel of the switch. The LED should - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 22
Managed Layer 2 Switches GSM7224 and GSM7248 Hardware Installation Guide SFP Modules The module bay accommodates a module seats into the connector. Figure 2-2 Connecting a Redundant Power Supply (RPS) Each switch has a redundant power supply (RPS) connector and a power receptacle on the rear. - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 23
switch, please go to the NETGEAR product support website http://www.kbserver.com. Select your product in the Product Support section of the screen. When the product support use the command line interface (CLI) to identify the IP address. If you are stacking switches, see "Connecting a Redundant Power - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 24
as both a print document and in PDF format on the Resource CD). • ProSafe 7200R Managed Switches CLI Reference Manual. Gives detailed examples of how to use the CLI, and is located on the Resource CD. • ProSafe 7000 Series Managed Switch Administration Guide. Describes configuration examples, and is - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 25
, and solutions of possible problems. Table 3-1. Troubleshooting Chart Problem Power LED is off. Cause No power is received Link LED is off or intermittent. Port connection is not working. Solution Check the power cord connections for the switch at the switch and the connected device. Make - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 26
integrity You can verify the integrity of the switch by resetting the switch. To reset the switch, use the Tools > Reset command, or remove AC power from the switch and then reapply AC power. If the problem continues, contact NETGEAR Technical Support. • Auto-negotiation The copper 10/100/1000 Mbps - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 27
ProSafe™ 24-Port L2 Managed Switch with Static Routing GSM7224 and ProSafe™ 48-Port L2 Managed Switch with Static Routing GSM7248. Default Settings The following table lists the factory default settings for the switches. You can use the RST (reset) button to return a switch to its factory default - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 28
Switches GSM7224 and GSM7248 Hardware Installation Guide Table A-1. Default Configuration Settings (continued) Features Admin edge port Link aggregation Port mirroring Traffic prioritization ACL GVRP GMRP IP routing MAC address aging SNMP community VLAN Ingress filtering GSM7224 Default Settings - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 29
, v2 Snooping Support • 802.1Q Static VLAN (Up to 4k) • 802.1p Class of Service (CoS) • 802.1D Spanning Tree Protocol (STP) • 802.1w Rapid Spanning Tree Protocol (RSTP) • 802.1s Multiple Spanning Tree Protocol (MSTP) • 802.3ad Link Aggregation (LACP) • IGMP v1, v2 Snooping Support Default Settings - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 30
Managed Layer 2 Switches GSM7224 and GSM7248 Hardware Installation Guide Table A-2. Technical Specifications (continued) Feature GSM7224 GSM7248 Layer 3 services • Static routing • ACL • DiffServ QOS • DHCP, BOOTP Relay • DHCP server • UDP Relay • ARP • IGMP querier • Static routing • ACL • - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 31
Managed Layer 2 Switches GSM7224 and GSM7248 Hardware Installation Guide Table A-2. Technical Specifications (continued) Feature GSM7224 Environment Operating: • Temperature 22.2 #950) • UL listed (UL 1950)/cUL IEC950/ EN60950 Default Settings and Technical Specifications A-5 v1.0, July 2009 - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 32
Managed Layer 2 Switches GSM7224 and GSM7248 Hardware Installation Guide A-6 Default Settings and Technical Specifications v1.0, July 2009 - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 33
/enu/winzerocfg/index.htm Configuration Utilities Internet Networking and TCP/IP http://documentation.netgear.com/reference/enu/tcpip/index.htm Addressing Wireless Communications http://documentation.netgear.com/reference/enu/wireless/index.htm Preparing a Computer for Network Access http - Netgear GSM7248v2 | GSM72XXv2 Hardware Installation Guide - Page 34
Managed Layer 2 Switches GSM7224 and GSM7248 Hardware Installation Guide B-2 Related Documents v1.0, July 2009
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
 |
 |
202-10351-02
July 2009
NETGEAR
, Inc.
350 E. Plumeria Drive
Sant Jose, CA 95134 USA
Managed Layer 2
Switches GSM7224 and
GSM7248 Hardware
Installation Guide