Netgear GSM7328Sv1 CLI Reference Manual for 7300S Series Layer-3 Stackable Swi
Netgear GSM7328Sv1 - ProSafe 24+4 Gigabit Ethernet L3 Managed Stackable Switch Manual
View all Netgear GSM7328Sv1 manuals
Add to My Manuals
Save this manual to your list of manuals |
Netgear GSM7328Sv1 manual content summary:
- Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 1
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, Software Version 7.3 NETGEAR, Inc. 350 Plumeria Dr. San Jose, CA 95124 USA 202-10237-05 October 2008 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 2
and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice. NETGEAR does not assume to certain restrictions. Please refer to the notes in the operating instructions. The Federal Office for Telecommunications Approvals has been notified of - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 3
Product and Publication Details Model Number: Publication Date: Product Family: Product Name: Home or Business Product: Language: Publication Part Number: Publication Version Number FSM73xxS/GSM73xxS October 2008 managed switch ProSafe 7300S Series Layer-3 Managed Stackable Switch Business English - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 4
iv v4.1, October 2008 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 5
1.1 Audience...1-1 1.2 Scope...1-1 1.3 Typographical Conventions 1-2 1.4 Special Message Formats 1-2 1.5 How to Use This Manual 1-3 1.6 How to Print this Manual 1-3 1.7 Revision History...1-4 Chapter 2 Overview 2.1 Product Concept ...2-1 2.2 Using the Command-Line Interface 2-2 2.2.1 Command - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 6
Protocol (HTTP) Commands 3-16 3.6.1 ip http secure-port 3-16 3.6.2 ip http secure-protocol 3-17 3.6.3 ip http secure-server 3-17 3.6.4 ip http server 3-17 3.6.5 ip http java 3-18 3.6.6 ip http session hard-timeout 3-18 3.6.7 ip http session maxsessions 3-18 3.6.8 ip http session soft-timeout - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 7
19 3.6.10 ip http secure-session maxsessions 3-20 3.6.11 ip http secure-session soft-timeout 3-20 3.6.12 network javamode 3-20 3.6.13 show ip http 3- 3-25 3.7.8 disconnect 3-26 Chapter 4 Port and System Setup Commands 4.1 Port Configuration Commands 4-1 4.1.1 interface...4-1 4.1.2 interface - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 8
port status 4-9 4.2 Pre-login Banner and System Prompt Commands address-table multicast 4-22 4.4.11 show mac-address-table static 4-23 4.4.12 show mac-address-table stats 4-23 4.5 DNS Client Commands 4-24 4.5.1 ip domain-lookup 4-25 4.5.2 ip domain-name 4-25 4.5.3 ip name-server 4-25 4.5.4 ip - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 9
4.5.5 clear host...4-26 4.5.6 show hosts 4-26 Chapter 5 Spanning Tree Protocol Commands 5.1 STP Configuration Commands 5-1 5.1.1 spanning-tree 5-1 5.1.2 spanning-tree bpdumigrationcheck 5-2 5.1.3 spanning-tree configuration name 5-2 5.1.4 spanning-tree configuration revision 5-3 5.1.5 spanning - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 10
6.1.2 vlan database 6-2 6.1.3 network mgmt_vlan 6-2 6.1.4 vlan...6-2 6.1.5 vlan acceptframe 6-3 6.1.6 vlan ingressfilter 6-3 6.1.7 vlan makestatic 6-4 6.1.8 vlan name...6-4 6.1.9 vlan participation 6-4 6.1.10 vlan participation all 6-5 6.1.11 vlan port acceptframe all 6-5 6.1.12 vlan port - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 11
ip dhcp pool ...7-2 7.1.1 client-identifier 7-2 7.1.2 client-name...7-3 7.1.3 default-router 7-3 7.1.4 dns-server ...7-3 7.1.5 hardware-address 7-8 7.2.1 ip dhcp excluded-address 7-8 7.2.2 ip dhcp ping packets 7-9 7.2.3 service dhcp 7-9 7.2.4 ip dhcp bootp automatic 7-10 7.2.5 ip dhcp conflict - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 12
7.4.1 ip dhcp relay information option 7-15 7.4.2 bootpdhcprelay 7-15 7.4.3 bootpdhcprelay maxhopcount 7-16 7.4.4 9.1.3 port-security max-static 9-3 9.1.4 port-security mac-address 9-3 9.1.5 port-security mac-address move 9-3 9.1.6 show port-security 9-4 9.1.7 show port-security - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 13
9.2 Storm Control Commands 9-5 9.2.1 storm-control broadcast 9-5 9.2.2 storm-control multicast all 9-6 9.2.3 storm-control unicast all 9-6 9.2.4 storm-control broadcast 9-7 9.2.5 storm-control multicast 9-7 9.2.6 storm-control unicast 9-8 9.2.7 storm-control flowcontrol 9-8 9.2.8 show storm- - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 14
-3 11.1.4 dot1x defaultlogin 11-3 11.1.5 dot1x initialize 11-3 11.1.6 dot1x login 11-3 11.1.7 dot1x max-req 11-4 11.1.8 dot1x port-control 11 .1.15 dot1x user 11-8 11.1.16 users defaultlogin 11-8 11.1.17 users login 11-9 11.1.18 show authentication 11-9 11.1.19 show authentication users 11 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 15
11.2.1 radius accounting mode 11-14 11.2.2 radius server host 11-14 11.2.3 radius server key 11-15 11.2.4 radius server msgauth 11-16 11.2.5 radius server primary 11-16 11.2.6 radius server retransmit 11-16 11.2.7 radius server timeout 11-17 11.2.8 show radius 11-17 11.2.9 show radius - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 16
12.2.2 show port-channel 12-6 Chapter 13 Quality of Service (QoS) Commands 13.1 Class of Service (CoS) Commands 13-1 13.1.1 classofservice dot1p-mapping 13-2 13.1.2 classofservice ip-precedence-mapping 13-2 13.1.3 classofservice ip-dscp-mapping 13-3 13.1.4 classofservice trust 13-3 13.1.5 cos - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 17
ip dscp 13-13 13.3.11 match ip precedence 13-13 13.3.12 match ip tos 13-14 13.3.13 match protocol 13-14 13.3.14 match source-address ip-dscp 13-20 13.4.8 mark ip-precedence 13-20 13.4.9 police-simple 13-20 13.4.10 policy-map rename 13-21 13.5 DiffServ Service Commands 13-21 13.5.1 service- - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 18
-5 14.1.11 show arp brief 14-6 14.2 IP Routing Commands 14-6 14.2.1 routing ...14-6 14.2.2 ip routing...14-7 14.2.3 ip address 14-7 14.2.4 ip route ...14-8 14.2.5 ip route default 14-9 14.2.6 ip route distance 14-9 14.2.7 ip forwarding 14-10 14.2.8 ip mtu...14-10 14.2.9 encapsulation 14-11 14 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 19
14-17 14.3.2 show ip vlan 14-17 14.4 Virtual Router Redundancy Protocol (VRRP) Commands 14-18 14.4.1 ip vrrp ...14-19 14.4.2 ip vrrp ...14-19 14.4.3 ip vrrp mode 14-20 14.4.4 ip vrrp ip 14-20 14.4.5 ip vrrp authentication 14-20 14.4.6 ip vrrp preempt 14-21 14.4.7 ip vrrp priority 14-21 14 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 20
cost 14-37 14.5.30 ip ospf dead-interval 14-37 14.5.31 ip ospf hello-interval 14-38 14.5.32 ip ospf priority 14-38 14.5.33 ip ospf retransmit-interval 14-39 14.5.34 ip ospf transmit-delay 14-39 14.5.35 ip ospf mtu-ignore 14-40 14.5.36 router-id 14-40 14 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 21
ospf virtual-link - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 22
ip igmpsnooping querier 15-10 15.3.2 ip igmpsnooping querier ip-address 15-10 15.3.3 ip igmpsnooping querier query-interval 15-11 15.3.4 show ip 12 show slot 17-6 17.1.13 show supported cardtype 17-7 17.1.14 show switch 17-8 17.1.15 show supported switchtype 17-9 17.2 Front Panel Stacking - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 23
17.2.2 qos-mode 17-11 17.2.3 show stack-port 17-11 17.2.4 show stack-port counters 17-12 17.2.5 show stack-port diag 17-12 Chapter 18 LLDP and LLDP-MED Commands 18.1 LLDP Commands 18-1 18.1.1 lldp transmit 18-1 18.1.2 no lldp transmit 18-1 18.1.3 lldp receive 18-1 18.1.4 no lldp receive 18 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 24
18.2.5 lldp med transmit-tlv 18-10 18.2.6 no lldp med transmit-tlv 18-10 18.2.7 lldp med faststartrepeatcount 18-10 18.2.8 no lldp med faststartrepeatcount 18-11 18.2.9 show lldp med 18-11 18.2.10 show lldp med interface 18-11 18.2.11 show lldp med local-device detail 18-12 18.2.12 show lldp - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 25
19.2.11 logout...19-21 19.2.12 ping...19-21 19.2.13 reload ...19-22 19.3 Logging Commands 19-22 19.3.1 logging buffered 19-22 19.3.2 logging buffered wrap 19-22 19.3.3 logging console 19-23 19.3.4 logging host 19-23 19.3.5 logging host remove 19-23 19.3.6 logging port 19-24 19.3.7 logging - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 26
UDP Relay Commands 20.1 UDP Relay Configuration Commands 20-2 20.1.1 ip helper-address (global config mode 20-2 20.1.2 ip helper-address (interface config mode 20-3 20.2 UDP Relay Show Commands 20-3 20.2.1 show ip helper-address 20-3 Appendix A Command Changes from Release 3 to Release 5 xxvi - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 27
basic knowledge of Ethernet and networking concepts. 1.2 Scope This manual is written for the 7300S Series Stackable Switch according to these specifications: Table 1-1. Manual Specifications Product Manual Part Number Manual Publication Date ProSafe 7300S Series Layer-3 Managed Stackable Switch - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 28
netgear.com/products/. 1.3 Typographical Conventions This guide uses the following typographical conventions: Table 1-2. Typographical conventions Italic Bold Fixed Italic Emphasis, books, CDs, file and server names, extensions User input, IP addresses 1-2 About This Manual v4.1, October 2008 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 29
possibly an button. Double-click on a link in the table of contents or index to navigate directly to where the topic is described in the manual. •A button to access the full NETGEAR, Inc. online knowledge base for the product model. • Links to PDF versions of the full - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 30
top left of any page. - Click the Complete PDF Manual link at the top left of any page in the manual. The PDF version of the complete manual opens in a browser window. - Click the print icon in the window toolbar. Tip: If your printer supports printing of two or more pages on a single sheet - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 31
by each networking device on which the 7300S Series Stackable Switch software base runs varies depending upon the platform and requirements of NETGEAR. 7300S Series Stackable Switch software includes a set of comprehensive management functions for managing both the switch and the network. You can - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 32
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 2.2 Using the Command-Line Interface The command-line interface (CLI) is a text-based way to manage and monitor the system. You can access the CLI by using a direct serial connection or by using a remote - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 33
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, The CLI Command Reference lists each command by the command name and provides a brief description of the command. Each command reference also contains the following information: • Format shows the command - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 34
backbone. Area IDs have the same format as IP addresses but are distinct from IP addresses. You can use the IP network number of the sub-netted network for the area ID. Enter the value of in dotted-decimal notation, such as 0.0.0.1. A router ID of 0.0.0.0 is invalid. Valid slot and port - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 35
immediately follow physical slots and identify portchannel (LAG) or router interfaces. The CPU slots immediately follow the logical slots. interfaces are only used for routing functions. CPU ports are handled by the driver as one or more physical entities located on physical slots. 2.2.4 Using the - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 36
function. Each of the command modes supports specific 7300S Series Stackable Switch software or enter the Global Configuration mode. Groups general setup commands and permits you to make modifications to an interface and provides access to the router interface configuration commands. Use this mode to - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 37
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, Table 2-5. CLI Command Modes (continued) Command Mode Prompt Policy Class Config Switch (Config policy-class-map)# Class Map Config Switch (Config class-map)# Tacacs Config MAC Access-list Config Switch - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 38
mode enter mac access-list extended . From the Global Config mode, enter ip dhcp pool . Stack Global Config Mode From the Global Config mode, enter -Z. 2.2.6 Entering CLI Commands The 7300S Series Stackable Switch supports several features to help you enter commands. 2.2.6.1 Command - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 39
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 2.2.6.2 CLI Error Messages If you enter a command and the system is unable to execute it, an error message appears. Table 2-7 describes the most common CLI error messages. Table 2-7. CLI Error Messages - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 40
of the router. Select DHCP, BootP, or None as the network config protocol. Configure the Management VLAN ID of the switch. If the help output shows a parameter in angle brackets, you must replace the parameter with a value. (switch) #network parms ? Enter the IP Address. If there - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 41
must use a direct connection to the console port. You cannot access the system remotely until the system has an IP address and subnet mask. You can set the network configuration information manually, or you can configure the system to accept these settings from a BOOTP or DHCP server on your network - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 42
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 2-12 v4.1, October 2008 Overview - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 43
Chapter 3 Administrative Access Commands This section describes the management access and basic port configuration commands available in the 7300S Series Stackable Switch CLI. This section contains the following topics: • Section 3.1 "Network Interface Commands" on page 1 • Section 3.3 "Console - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 44
network parms (parameter) This command sets the IP Address, subnet mask and gateway of the device. The IP Address and the gateway must be on the same none parameter, you must configure the network information for the switch manually. Default none Format network protocol {none | bootp | dhcp} - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 45
which traffic is switched or routed. Format show network Modes Privileged EXEC User EXEC IP Address The IP address of the interface. The factory default value is 0.0.0.0 Subnet Mask The IP subnet mask for this interface. The factory default value is 0.0.0.0 Default Gateway The default - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 46
manage the switch via the web GUI or telnet, an IP address needs to be assigned to the switch management CPU. Whereas there are CLI commands that can be used to do this, ezconfig simplifies the task. The tool is applicable to all NETGEAR 7000-series managed switches, and allows you to configure - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 47
for the ProSafe 7300S Series Layer-3 Stackable Switches, The following is an example of an ezconfig session. NETGEAR EZ Configuration Utility Hello and Welcome! This utility will walk you thru assigning the IP address for the switch management CPU. It will allow you to save the changes at the end - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 48
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, There are changes detected, do you wish to save the changes permanently (Y/N)? y The configuration changes have been saved succesfully. Please enter 'show running-config' to see the final configuration. Thanks - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 49
for the ProSafe 7300S Series Layer-3 Stackable Switches, 3.3.3 serial baudrate This command specifies the communication rate of the terminal interface. The supported rates are 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200. Default 9600 Format serial baudrate {1200 | 2400 | 4800 | 9600 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 50
show serial This command displays serial communication settings for the switch. Format show serial Modes Privileged EXEC User EXEC Serial Port Login Timeout (minutes) Specifies the time, in minutes, of inactivity on a Serial port connection, after which the Switch will close the connection - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 51
the device from a remote management host. 3.4.1 telnet This command establishes a new outbound telnet connection to a remote host. The host value must be a valid IP address. Valid values for port should be a valid decimal integer in the range of 0 to 65535, where the default value is 23. If [debug - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 52
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 3.4.3 transport output telnet This command regulates new outbound telnet connections. If enabled, new outbound telnet sessions can be established until it reaches the maximum number of simultaneous outbound - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 53
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 3.4.5 session-timeout This command sets the telnet session timeout value.The timeout value unit of time is minutes. A value of 0 indicates that a session remains active indefinitely. Default 0 Format - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 54
EXEC 3.4.8 show telnet This command displays the current outbound telnet settings. Format show telnet Modes Privileged EXEC User EXEC Outbound Telnet Login Timeout Indicates the number of minutes an outbound telnet session is allowed to remain inactive before being logged off. 3-12 v4 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 55
sessions are allowed. 3.4.9 show telnetcon This command displays telnet settings. Format show telnetcon Modes Privileged EXEC User EXEC Remote Connection Login Timeout (minutes) This object indicates the number of minutes a remote connection session is allowed to remain inactive before being - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 56
This command is used to enable SSH. Default disabled Format ip ssh Mode Privileged EXEC 3.5.1.1 no ip ssh This command is used to disable SSH. Format no ip ssh Mode Privileged EXEC 3.5.2 ip ssh protocol This command is used to set or remove protocol levels (or versions) for SSH. Either - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 57
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 3.5.3 sshcon maxsessions This command specifies the maximum number of SSH connection sessions that can be established. A value of 0 indicates that no ssh connection can be established. The range is 0 to 5. - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 58
by using a Web browser is enabled by default. Everything you can view and configure by using the CLI is also available by using the Web. 3.6.1 ip http secure-port This command is used to set the SSL port where port can be 1-65535 and the default is port 443. Default 443 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 59
to disable the secure socket layer for secure HTTP. Format no ip http secure-server Mode Privileged EXEC 3.6.4 ip http server This command enables access to the switch through the Web interface. When access is enabled, you can login to the switch from the Web interface. When access is disabled - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 60
java This command disables the Web Java mode. The Java mode applies to both secure and unsecure Web connections. Format no ip http java Mode Privileged EXEC 3.6.6 ip http session hard-timeout Configures the hard timeout for un-secure HTTP sessions in hours. Configuring this value to zero will - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 61
begins on initiation of the Web session and is restarted with each access to the switch. Default 60 Format ip http session soft-timeout Mode Privileged EXEC 3.6.8.1 no ip http session soft-timeout Resets the soft timeout for un-secure HTTP sessions to the default value. Format no - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 62
secure-session maxsessions Restores the the number of allowable secure HTTP sessions to the default value. Format no ip http secure-session maxsessions Mode Privileged EXEC 3.6.11 ip http secure-session soft-timeout Configures the soft timeout for secure HTTP sessions in minutes. When this - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 63
, the user cannot view the Java applet. Format no network javamode Mode Privileged EXEC 3.6.13 show ip http This command displays the http settings for the switch. Format show ip http Mode Privileged EXEC HTTP Mode (Unsecure) Indicates the unsecure administrative mode. Java Mode Maximum - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 64
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 3.7 User Account Commands This section describes the commands you use to add, manage, and delete system users. The 7300S Series Stackable Switch has two default users: admin and guest. The admin user can view - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 65
Global Config 3.7.3 users snmpv3 accessmode This command specifies the snmpv3 access privileges for the specified login user. The valid accessmode values are readonly or readwrite. The is the login user name for which the specified access mode applies. The default is readwrite for the - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 66
are none, md5 or sha. If you specify md5 or sha, the login password is also used as the snmpv3 authentication password and therefore must be at the user is prompted for the key. When you use the des protocol, the login password is also used as the snmpv3 encryption password, so it must be a minimum - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 67
serial port connections to the switch. Format show loginsession Mode Privileged EXEC ID Login Session ID User Name The name the user will use to login using the serial port or Telnet. Connection From IP address of the Telnet client machine or EIA-232 for the serial port connection. Idle - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 68
mode. This field displays the authentication protocol to be used for the specified login user. This field displays the encryption protocol to be used for the specified login user. 3.7.8 disconnect This command closes a telnet session. Format disconnect { | all} Mode Privileged - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 69
topics: • Section 4.1 "Port Configuration Commands" on page 1 • Section 4.2 "Pre-login Banner and System Prompt Commands" on page 10 • Section 4.3 "Simple Network Time Protocol (SNTP) Commands" on page 11 • Section 4.4 "MAC Address and MAC Database Commands" on page 17 • Section 4.5 "DNS Client - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 70
group and an IP address assigned to the VLAN group. Format Mode interface lag Global Config 4.1.5 auto-negotiate This command enables automatic negotiation on a port. Default enabled Format auto-negotiate Mode Interface Config 4-2 Port and System Setup Commands v4.1, October - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 71
create an alpha-numeric description of the port. The length can be up to 64 characters. Format description Mode Interface Config Port and System Setup Commands 4-3 v4.1, October 2008 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 72
that Layer-2 headers might require. To configure the IP MTU size, which is the maximum size of the IP packet (IP Header + IP payload), see Section 14.2.8 "ip mtu" on page 10. Default Format Mode Format Mode enabled shutdown Interface Config 4-4 Port and System Setup Commands v4.1, October 2008 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 73
This command sets the speed and duplex setting for the interface. Format speed { } Mode Interface Config Port and System Setup Commands 4-5 v4.1, October 2008 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 74
physical monitored port. Format monitor session {source interface | destination interface | mode} Mode Global Config 4-6 Port and System Setup Commands v4.1, October 2008 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 75
destination monitored port and all VLANs. Once the port is removed from the VLAN, the user must manually add the port to any desired VLANs. Note: This command sets the monitor session (port monitoring interface configured as the mirrored port. Port and System Setup Commands 4-7 v4.1, October 2008 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 76
default is enabled. Physical Mode Selects the desired port speed and duplex mode. If auto-negotiation support is selected, then the duplex mode and speed is set from the auto-negotiation process. Note via the "description" command 4-8 Port and System Setup Commands v4.1, October 2008 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 77
Whether the port is in loop state or not. Partner Flow Control Whether the remote side is using flow control or not. Port and System Setup Commands 4-9 v4.1, October 2008 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 78
section describes the commands you use configure the pre-login banner and the system prompt. The pre-login banner is the text that displays before you login at the User: prompt. 4.2.1 copy The copy Mode Privileged EXEC 4-10 v4.1, October 2008 Port and System Setup Commands - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 79
4.3.2.1 no sntp client mode This command disables Simple Network Time Protocol (SNTP) client mode. Format no sntp client mode Mode Global Config Port and System Setup Commands v4.1, October 2008 4-11 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 80
in seconds to a value from 130. Default 5 Format sntp unicast client poll-timeout Mode Global Config 4-12 v4.1, October 2008 Port and System Setup Commands - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 81
resets the poll interval for SNTP multicast clients to its default value. Format no sntp multicast client poll-interval Mode Global Config Port and System Setup Commands v4.1, October 2008 4-13 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 82
sntp client This command is used to display SNTP client settings. Format show sntp client Mode Privileged EXEC 4-14 v4.1, October 2008 Port and System Setup Commands - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 83
Address IP Address of configured SNTP Server. Address Type Address Type of configured SNTP server. Priority IP priority type of the configured server. Version SNTP Version number of the server. The protocol version used to query the server in unicast mode. Port and System Setup Commands v4 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 84
difference with UTC Minutes-offset Number of minutes difference with UTC Mode Global Config Default [no] clock timezone 4-16 v4.1, October 2008 Port and System Setup Commands - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 85
locally-administered MAC address. Default burnedin Format network mac-type {local | burnedin} Mode Privileged EXEC 4.4.2.1 no network mac-type This command resets the value of MAC address to its default. Format no network mac-type Mode Privileged EXE Port and System Setup Commands v4 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 86
be specified as a 6-byte hexadecimal number in the format of b1:b2:b3:b4:b5:b6. The restricted MAC Addresses are: 00:00:00:00:00:00, 01:80:C2:00:00:00 to 01:80:C2:00:00:0F, Format macfilter adddest Mode Interface Config 4-18 v4.1, October 2008 Port and System Setup Commands - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 87
addsrc This command adds the interface to the source filter set for the MAC filter with the MAC address of and VLAN of . The parameter must be specified as a addsrc Mode Interface Config Port and System Setup Commands v4.1, October 2008 4-19 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 88
macfilter addsrc all This command removes a port from the source filter set for the MAC filter with the MAC address of and VLAN of . The parameter must be specified as a 6-byte hexadecimal all Mode Global Config 4-20 v4.1, October 2008 Port and System Setup Commands - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 89
agetime of all forwarding databases. 4.4.8.1 no bridge aging-time This command sets the forwarding database address aging timeout to 300 seconds. In an IVL system, the [fdbid | all] parameter is configure all forwarding database's agetime. Port and System Setup Commands v4.1, October 2008 4-21 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 90
by colons, for example 01:23:45:67:89:AB. In an IVL system the MAC address will be displayed as a MAC address and VLAN ID combination of 8 bytes. Type This displays the type of the entry. Static description of this multicast table entry. 4-22 v4.1, October 2008 Port and System Setup Commands - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 91
removing the interfaces that are listed as the static filtering interfaces. 4.4.11 show mac-address-table static This command displays the Static MAC Filtering information for all Static MAC Filters. current number of entries in the MFDB. Port and System Setup Commands v4.1, October 2008 4-23 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 92
service. DNS is used to translate domain names to IP addresses service to other components in the switch. The client contacts one or more DNS servers to resolve a hostname to an IP address. The DNS servers list is configured by providing an IP address support domain name in addition to the IP address - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 93
is a string of 1 to 255 characters. Format ip domain-name name no ip domain-name Mode Global Config 4.5.3 ip name-server To set the available name servers, use the ip name-server global configuration command. is IP addresses of the name server. Up to 8 servers can be - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 94
ip host To define static host name to IP address mapping in the host cache, use the ip address mapping, use the no form of this command. Format [no] ip host name address Mode Global Config 4.5.5 clear host To delete entries from the host name-to-address and addresses, use - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 95
Chapter 5 Spanning Tree Protocol Commands This section describes the spanning tree protocol (STP) commands available in the 7300S Series Stackable Switch CLI. STP helps prevent network loops, duplicate messages, and network instability. The STP Commands section includes the following topics: • - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 96
the configuration that this switch is currently using. The is a string of up to 32 characters. Default base MAC address in hexadecimal notation Format spanning-tree configuration name Mode Global Config 5.1.3.1 no spanning-tree configuration name This command resets the - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 97
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 5.1.4 spanning-tree configuration revision This command sets the Configuration Identifier Revision Level for use in identifying the configuration that this switch is currently using. The Configuration - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 98
) • 802.1w - RST BPDUs are transmitted rather than MST BPDUs (IEEE 802.1w functionality supported) • 802.1s - MST BPDUs are transmitted (IEEE 802.1s functionality supported) Default 802.1s Format spanning-tree forceversion Mode Global Config 5.1.7.1 no spanning - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 99
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 5.1.8.1 no spanning-tree forward-time This command sets the Bridge Forward Delay parameter for the common and internal spanning tree to the default value of 15. Format no spanning-tree forward-time Mode - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 100
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 5.1.11 spanning-tree max-hops This command sets the MSTP Max Hops parameter to a new value for the common and internal spanning tree. The max-hops value is a range from 1 to 127. Default 20 Format - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 101
is a number within a range of 1 to 4094, that corresponds to the new instance ID to be added. The maximum number of multiple instances supported by the switch is 4. Format spanning-tree mst instance Mode Global Config Spanning Tree Protocol Commands 5-7 v4.1, October 2008 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 102
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 5.1.13.1 no spanning-tree mst instance This command removes a multiple spanning tree instance from the switch and reallocates all VLANs allocated to the deleted instance to the common and internal spanning - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 103
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 5.1.15 spanning-tree mst vlan This command adds an association between a multiple spanning tree instance and a VLAN so that the VLAN is no longer associated with the common and internal spanning tree. The - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 104
-tree bpduforwarding Normally a switch will not forward Spanning Tree Protocol (STP) BPDU packets if STP is disabled. However, if in some network setup, the user wishes to forward BDPU packets received from other network devices, this command can be used to enable the forwarding. Default disabled - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 105
for the CST. It is made up using the bridge priority and the base MAC address of the bridge. Time in seconds. Number of times changed. Boolean value of the root bridge. It is made up from the bridge priority and the base MAC address of the bridge. Value of the Root Path Cost parameter for the common - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 106
MST instance. It is made up using the bridge priority and the base MAC address of the bridge. Bridge Max Age Configured value. Bridge Max Hops Bridge max Tree Adminmode Enabled or disabled. Spanning Tree Version Version of 802.1 currently supported (IEEE 802.1s, IEEE 802.1w, or IEEE 802.1d) - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 107
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, Configuration Revision Level Configuration Digest Key MST Instances Identifier used to identify the configuration currently being used. Identifier used to identify the configuration currently being used. List - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 108
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, MSTP BPDUs Received Multiple Spanning Tree Protocol Bridge Protocol Data Units received. 5.2.4 show spanning-tree mst port detailed This command displays the detailed settings and parameters for a specific - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 109
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, Designated Port Cost Designated Bridge Designated Port Identifier Path Cost offered to the LAN by the Designated Port Bridge Identifier of the bridge with the Designated Port. Port on the Designated Bridge - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 110
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, Point To Point MAC Status CST Regional Root CST Port Cost Derived value indicating if this port is part of a point to point link. The regional root identifier in use for this port. The configured path cost - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 111
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, MST Instance ID List For each MSTID: Associated FIDs Associated VLANs List of multiple spanning trees IDs currently configured. List of forwarding database identifiers associated with this instance. List of - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 112
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 5-18 Spanning Tree Protocol Commands v4.1, October 2008 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 113
to create a MAC-based VLAN. Format vlan association mac Mode VLAN Config Association options are: Mac Address A MAC address for which the switch has forwarding and/or filtering information. The format is 6 or 8 two-digit hexadec- VLAN Commands 6-1 v4.1, October 2008 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 114
:67:89:AB. A VLAN Identifier (VID) is associated with each VLAN. 6.1.1.1 no vlan association mac This command removes the association of a MAC address to a VLAN. Format no vlan association mac Mode VLAN Config Association options are the same as for the vlan association mac - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 115
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 6.1.4.1 no vlan This command deletes an existing VLAN. The ID is a valid VLAN identification number (ID 1 is reserved for the default VLAN). The VLAN range is 1-4093. Format no vlan Mode VLAN - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 116
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 6.1.6.1 no vlan ingressfilter This command disables ingress filtering. If ingress filtering is disabled, frames received with VLAN IDs that do not match the VLAN membership of the receiving interface are - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 117
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, Participation options are: include exclude auto The interface is always a member of this VLAN. This is equivalent to registration fixed. The interface is never a member of this VLAN. This is equivalent to - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 118
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, With either option, VLAN tagged frames are forwarded in accordance with the IEEE 802.1Q VLAN Specification. Default all Format vlan port acceptframe all {vlanonly | all} Mode Global Config 6.1.11.1 no - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 119
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 6.1.13.1 no vlan port tagging all This command configures the tagging behavior for all interfaces in a VLAN to disabled. If tagging is disabled, traffic is transmitted as untagged frames. The ID is a valid - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 120
associated with the group, this command will fail and the protocol will not be added to the group. The possible values for protocol are ip, arp, and ipx. Default none Format vlan protocol group add protocol Mode Global Config 6.1.16.1 no vlan protocol group add protocol - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 121
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 6.1.18.1 no protocol group This command removes the from this protocol-based VLAN group that is identified by this . Format no protocol group Mode VLAN Config 6.1.19 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 122
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 6.1.20.1 no protocol vlan group all This command removes all interfaces from this protocol-based VLAN group that is identified by this . Format no protocol vlan group all Mode Global - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 123
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 6.2 VLAN Show Commands This section describes the commands you use to view VLAN settings. 6.2.1 show vlan This command displays a list of all configured VLANs. Format show vlan Modes Privileged EXEC - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 124
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, Interface Current Configured Tagging Valid slot and port number separated by forward slashes. It is possible to set the parameters for all ports by using the selectors on the top line. Determines the degree - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 125
show vlan association mac This command displays the VLAN associated with a specific configured MAC address. If no MAC address is specified, the VLAN associations of all the configured MAC addresses are displayed. Format show vlan association mac [] Modes Privileged EXEC User EXEC Mac - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 126
used to enable Double VLAN Tunneling on the specified interface. Note: When you use the mode dot1q-tunnel command on an interface, it becomes a service provider port. Ports that do not have double VLAN tunneling enabled are customer ports. Default disabled 6-14 v4.1, October 2008 VLAN Commands - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 127
enable Double VLAN Tunneling on the specified interface. Note: When you use the mode dvlan-tunnel command on an interface, it becomes a service provider port. Ports that do not have double VLAN tunneling enabled are customer ports. Default Format Mode disabled mode dvlan-tunnel Interface Config - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 128
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 6.3.4 show dot1q-tunnel This command displays all interfaces enabled for Double VLAN Tunneling. Format show dot1q-tunnel Modes Privileged EXEC User EXEC Interface Valid slot and port number separated by - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 129
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 6.3.6 show dvlan-tunnel This command displays all interfaces enabled for Double VLAN Tunneling. Format show dvlan-tunnel Modes Privileged EXEC User EXEC Interface Valid slot and port number separated by - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 130
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 6.4.1 vlan port priority all This command configures the port priority assigned for untagged packets for all ports presently plugged into the device. The range for the priority is 0-7. Any subsequent per port - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 131
Stackable Switch CLI. DHCP automatically allocates and manages client TCP/ IP configurations. DHCP uses UDP as its transport protocol and supports a number of features that facilitate in administration address allocations. The DHCP Server Commands section includes the following topics: • Section - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 132
to DHCP Pool Config mode when you successfully execute this command. 7.1.0.1 no ip dhcp pool This command removes the DHCP address pool. The name should be previously configured pool name. Format no ip dhcp pool Mode Global Config 7.1.1 client-identifier This command specifies the - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 133
DHCP Pool Config 7.1.3.1 no default-router This command removes the default router list. Format no default-router Mode DHCP Pool Config 7.1.4 dns-server This command specifies the IP servers available to a DHCP client. Address parameters are valid IP addresses; each made up of four decimal - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 134
Mode DHCP Pool Config 7.1.6 host This command specifies the IP address and network mask for a manual binding to a DHCP client. Address and Mask are valid IP addresses; each made up of four decimal bytes ranging from 0 to 255. IP address 0.0.0.0 is invalid. The prefix-length is an integer from - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 135
Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 7.1.7 lease This command configures the duration of the lease for an IP address that is assigned from a DHCP server to a DHCP client. The overall lease time should be between 1-86400 minutes. If infinite is specified - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 136
7.1.11 netbios-name-server This command configures NetBIOS Windows Internet Naming Service (WINS) name servers that are available to DHCP clients. One IP address is required, although one can specify up to eight addresses in one command line. Servers are listed in order of preference (address1 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 137
. Format no netbios-node-type Mode DHCP Pool Config 7.1.13 next-server This command configures the next server in the boot process of a DHCP client. Address is the IP address of the next server in the boot process, which is typically a TFTP server. Default inbound interface helper - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 138
. You must be in Global Config mode to execute these commands. 7.2.1 ip dhcp excluded-address This command specifies the IP addresses that a DHCP server should not assign to DHCP clients. Low-address and high-address are valid IP addresses; each made up of four decimal bytes ranging from 0 to 255 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 139
This command prevents the server from pinging pool addresses and sets the number of packets to 0. Default 0 Format no ip dhcp ping packets Mode Global Config 7.2.3 service dhcp This command enables the DHCP server. Default disabled Format service dhcp Mode Global Config DHCP Commands - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 140
the DHCP server. Format no service dhcp Mode Global Config 7.2.4 ip dhcp bootp automatic This command enables the allocation of the addresses to the bootp client. The addresses are from the automatic address pool. Default disabled Format ip dhcp bootp automatic Mode Global Config - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 141
bindings corresponding to all the addresses are deleted. is a valid IP address made up of four decimal bytes ranging from 0 to 255. IP address 0.0.0.0 is invalid. Default none Format clear ip dhcp binding {address | *} Mode Privileged EXEC 7.3.2 clear ip dhcp server statistics This - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 142
configuration This command displays address bindings for the specific IP address on the DHCP server. If no IP address is specified, the bindings corresponding to all the addresses are displayed. Format show ip dhcp global configuration Modes Privileged EXEC User EXEC Service DHCP The field to - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 143
unique identifier of a DHCP client. Hardware Address The hardware address of a DHCP client. Hardware Address Type The protocol of the hardware platform. Host The IP address and the mask for a manual binding to a DHCP client. 7.3.7 show ip dhcp server statistics This command displays DHCP - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 144
conflicts logged by the DHCP Server. If no IP address is specified, all the conflicting addresses are displayed. Format show ip dhcp conflict [ip-address] Modes Privileged EXEC User EXEC IP address The IP address of the host as recorded on the DHCP server. Detection Method The manner - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 145
client request originated. The remote ID option contains the MAC address of the relay agent (the switch management CPU's own MAC address). Default disabled Format ip dhcp relay information option Mode Global Config 7.4.1.1 no ip dhcp relay information option This command disables the relay - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 146
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 7.4.3 bootpdhcprelay maxhopcount This command configures the maximum allowable relay agent hops for BootP/DHCP Relay on the system. The parameter has a range of 1 to 16. Default 4 Format - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 147
hops. Minimum Wait Time (Seconds) Is the minimum wait time. Admin Mode Represents whether relaying of requests is enabled or disabled. Server IP Address Is the IP Address for the BootP/DHCP Relay server. Circuit Id Option Mode Is the DHCP circuit Id option which may be enabled or disabled - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 148
7300S Series Layer-3 Stackable Switches, Packets Discarded Is the number of packets discarded. 7.4.7 bootpdhcprelay backup-serverip To configure the IP address of the backup DHCP server , use the bootpdhcprelay backup-serverip command. When the DHCP client request is received, the - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 149
Chapter 8 GARP, GVRP, and GMRP Commands This section describes the Generic Attribute Registration Protocol (GARP), GARP VLAN Registration Protocol (GVRP), and Garp Multicast Registration Protocol (GVMP) commands available in the 7300S Series Stackable Switch CLI. GARP is a protocol that allows - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 150
the VLAN entry. This can be considered a buffer time for another station to assert registration for the same attribute in order to maintain uninterrupted service.time is 20 to 600 (centiseconds). The value 60 centiseconds is 0.6 seconds. Note: This command has an effect only when GVRP is enabled - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 151
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, Format Modes no set garp timer leave Interface Config Global Config 8.1.2 set garp timer leaveall This command sets how frequently Leave All PDUs are generated. A Leave All PDU indicates that all - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 152
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, GMRP Admin Mode GVRP Admin Mode This displays the administrative mode of GMRP for the system. This displays the administrative mode of GVRP for the system 8.2 GVRP Commands This section describes the - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 153
group. This may be considered a buffer time for another station to assert registration for the same attribute in order to maintain uninterrupted service. There is an instance of this timer on a per-Port, perGARP participant basis. Permissible values are 20 to 600 centiseconds (0.2 to 6.0 seconds - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 154
to the same segment. GMRP also allows group membership information to propagate across all networking devices in the bridged LAN that support Extended Filtering Services. Note: If GMRP is disabled, the system does not forward GMRP messages. 8.3.1 set gmrp adminmode This command enables GARP - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 155
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 8.3.2 set gmrp interfacemode This command enables GARP Multicast Registration Protocol. If an interface which has GARP enabled is enabled for routing or is enlisted as a member of a port-channel (LAG), GARP - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 156
group. This may be considered a buffer time for another station to assert registration for the same attribute in order to maintain uninterrupted service. There is an instance of this timer on a per-Port, perGARP participant basis. Permissible values are 20 to 600 centiseconds (0.2 to 6.0 seconds - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 157
is 6 or 8 two-digit hexadecimal numbers that are separated by colons, for example 01:23:45:67:89:AB. In an IVL system the MAC address is displayed as 8 bytes. Type Displays the type of the entry. Static entries are those that are configured by the end user. Dynamic entries are - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 158
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 8-10 GARP, GVRP, and GMRP Commands v4.1, October 2008 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 159
Port security, which is also known as port MAC locking, allows you to secure the network by locking allowable MAC addresses on a given port. Packets with a matching source MAC address are forwarded normally, and all other packets are discarded. Note: To enable the SNMP trap specific to port security - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 160
-security max-dynamic Mode Interface Config 9.1.2.1 no port-security max-dynamic This command resets the maximum of dynamically locked MAC addresses allowed on a specific port to its default value. Format no port-security max-dynamic Mode Interface Config 9-2 Port-Based Traffic - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 161
ProSafe 7300S Series Layer-3 Stackable Switches, 9.1.3 port-security max-static This command sets the maximum number of statically locked MAC addresses allowed on a specific port. Default 20 Format port-security max-static Mode Interface Config 9.1.3.1 no port-security max-static - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 162
EXEC Interface Admin Mode Port Locking mode for the Interface. Dynamic Limit Maximum dynamically allocated MAC Addresses. Static Limit Maximum statically allocated MAC Addresses. Violation Trap Mode Whether violation traps are enabled. 9.1.8 show port-security dynamic This command displays - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 163
of the last packet that was discarded on a locked port. Format show port-security violation Mode Privileged EXEC MAC Address MAC Address of discarded packet on locked port. 9.2 Storm Control Commands This section describes commands you use to configure storm control and view - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 164
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 9.2.1.1 no storm-control broadcast This command disables broadcast storm recovery mode. The threshold implementation follows a percentage pattern. If the broadcast traffic on any Ethernet port exceeds the - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 165
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 9.2.3.1 no storm-control unicast all This command disables multicast storm recovery mode. Format no storm-control unicast all Mode Global Config 9.2.4 storm-control broadcast This command enables - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 166
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 9.2.5.1 no storm-control multicast This command disables multicast storm recovery mode. Format no storm-control multicast [] Mode Interface Config 9.2.6 storm-control unicast This command enables - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 167
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 9.2.7.1 no storm-control flowcontrol This command disables 802.3x flow control for the switch. Note: This command only applies to full-duplex mode ports. Format Mode no storm-control flowcontrol Global - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 168
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, Default Format Mode unprotected switchport protected [] Interface Config 9.3.1.1 no switchport protected This command removes an interface from a set of protected ports. Format no switchport - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 169
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, By default, a port does not belong to any private group. A port cannot be in more than one private group. An error message should return when that occurred. To change a port's private group, first the port - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 170
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 9.4.5 show private-group This command displays the private groups' information. Format show private-groupname [||port ] Mode Priviledged EXEC - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 171
Chapter 10 SNMP Commands This section describes the SNMP commands available in the 7300S Series Stackable Switch CLI. You can configure the switch to act as a Simple Network Management Protocol (SNMP) agent so that it can communicate with SNMP managers on your network. The SNMP Commands section - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 172
10.1.3 snmp-server community ipaddr This command sets a client IP address for an SNMP community. The address is the associated community SNMP packet sending address and is used along with the client IP mask value to denote a range of IP addresses from which SNMP clients may use that community to - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 173
of 255.255.255.255 will allow access from only one station, and will use that machine's IP address for the client IP Address. A value of 0.0.0.0 will allow access from any IP address. The name is the applicable community name. Default 0.0.0.0 Format snmp-server community ipmask - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 174
Config 10.1.8 snmp-server traps violation This command enables the sending of new violation traps designating when a packet with a disallowed MAC address is received on a locked port. Note: For other port security commands, see Section 9.1, "Port Security Commands". Default Format Mode disabled - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 175
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 10.1.8.1 no snmp-server traps violation This command disables the sending of new violation traps. Format no snmp-server traps violation Mode Interface Config 10.1.9 snmp-server traps This command - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 176
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 10.1.11 snmp-server traps linkmode This command enables Link Up/Down traps for the entire switch. When enabled, link traps are sent only if the Link Trap flag setting associated with the port is enabled. - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 177
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 10.1.13.1 no snmp-server traps stpmode This command disables the sending of new root traps and topology change notification traps. Format no snmp-server traps stpmode Mode Global Config 10.1.14 snmptrap - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 178
> can be snmpv1 or snmpv2. Note: This command does not support a "no" form. Default Format Mode snmpv2 snmptrap snmpversion Global Config 10.1.16 snmptrap ipaddr This command assigns an IP address to a specified community name. The maximum length of name is - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 179
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 10.1.18 snmp trap link-status This command enables link status traps by interface. Note: This command is valid only when the Link Up/Down Flag is enabled. See 'snmp-server enable traps linkmode' command. - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 180
show snmpcommunity This command displays SNMP community information. Six communities are supported. You can add, change, or delete communities. The switch of this table must contain a unique community name. Client IP Address An IP address (or portion thereof) from which this device will accept - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 181
receivers are simultaneously supported. Format show snmptrap Mode Privileged EXEC SNMP Trap Name The community string of the SNMP trap packet sent to the trap manager. The string is case sensitive and can be up to 16 alphanumeric characters. IP Address The IP address to receive SNMP traps - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 182
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, Authentication Flag Link Up/Down Flag Multiple Users Flag Spanning Tree Flag Broadcast Storm Flag DVMRP Traps OSPF Traps PIM Traps Can be enabled or disabled. The factory default is enabled. Indicates whether - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 183
802.1x). Port-based network access control allows you to permit access to network services only to and devices that are authorized and authenticated. 11.1.1 authentication login This command creates an authentication login list. The is any character string and is not case sensitive. Up to - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 184
using the RADIUS server. The value of reject indicates the user is never authenticated. To authenticate a user, the first authentication method in the user's login (authentication login list) is attempted. The 7300S Series Stackable Switch software does not utilize multiple entries in the user - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 185
mode is not 'auto' an error will be returned. Format dot1x initialize Mode Privileged EXEC 11.1.6 dot1x login This command assigns the specified authentication login list to the specified user for 802.1x port security. The parameter must be a configured user and the - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 186
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 11.1.7 dot1x max-req This command sets the maximum number of times the authenticator state machine on this port will transmit an EAPOL EAP Request/Identity frame before timing out the supplicant. The - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 187
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 11.1.8.1 no dot1x port-control This command sets the authentication mode to be used on the specified port to 'auto'. Format no dot1x port-control Mode Interface Config 11.1.9 dot1x port-control all This - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 188
machine on this port. Depending on the token used and the value (in seconds) passed, various timeout configurable parameters are set. The following tokens are supported. reauth-period: Sets the value, in seconds, of the timer used by the authenticator state machine on this port to determine when re - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 189
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, quiet-period: Sets the value, in seconds, of the timer used by the authenticator state machine on this port to define periods of time in which it will not attempt to acquire a supplicant. The quiet-period must - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 190
packets; the macbased mode only forward packets for the MAC address that is being authenticated Format dot1x port-method {macbased | all} Mode Global Config 11.1.16 users defaultlogin This command assigns the authentication login list to use for non-configured users when attempting to log in to - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 191
list, if any. 11.1.19 show authentication users This command displays information about the users assigned to the specified authentication login list. If the login is assigned to non-configured users, the user "default" will appear in the user column. Format show authentication users - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 192
Series Layer-3 Stackable Switches, User Component This field displays the user assigned to the specified authentication login list. This field displays the component (User or 802.1x) for which the authentication login list is assigned. 11.1.20 show dot1x This command is used to show a summary of - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 193
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, Protocol Version PAE Capabilities Authenticator PAE State Backend Authentication State Quiet Period Transmit Period Supplicant Timeout Server Timeout Maximum Requests The protocol version associated with this - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 194
. Last EAPOL Frame Version The protocol version number carried in the most recently received EAPOL frame. Last EAPOL Frame Source The source MAC address carried in the most recently received EAPOL frame. EAP Response/Id Frames Received The number of EAP response/identity frames that have been - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 195
access to the specified port. 11.1.22 show users authentication This command displays all user and all authentication login information. It also displays the authentication login list assigned to the default user. Format show users authentication Mode Privileged EXEC User Lists every user - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 196
Series Stackable Switch to use a Remote Authentication Dial-In User Service (RADIUS) server on your network for authentication and accounting. server. If you use the parameter, the command configures the IP address to use to connect to a RADIUS authentication server. You can configure up - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 197
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, If you use the parameter, the command configures the IP address to use for the RADIUS accounting server. You can only configure one accounting server. If an accounting server is currently configured, use - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 198
server is already configured prior to this command being executed, the server specified by the IP address specified used in this command will become the new primary server. The IP address must match that of a previously configured RADIUS authentication server. Format radius server primary - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 199
RADIUS servers. Format show radius [servers] Mode Privileged EXEC Primary Server IP Address Shows the configured server currently in use for authentication. Number of configured servers The configured IP address of the authentication server. Max number of retransmits The configured value of - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 200
. Yes or No. If you include the optional [servers] parameter, the following information regarding the configured RADIUS servers is displayed. IP Address IP Address of the configured RADIUS server. Port The port in use by this server. Type Primary or secondary. Secret Configured Yes / No - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 201
This command is used to display the statistics for RADIUS or configured server. To show the configured RADIUS server statistic, the IP Address specified must match that of a previously configured RADIUS server. On execution, the following fields are displayed. Format show radius statistics [ipaddr - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 202
you do not specify an IP address, then only the Invalid Server Address field is displayed. Otherwise other listed fields are displayed. Invalid Server Addresses The number of RADIUS Access-Response packets received from unknown addresses. Server IP Address IP Address of the Server. Round Trip - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 203
Series Stackable Switch to use 802.1x Option 81. 11.3.1 radius server attribute 4 This command is used to set the NAS-IP address for the RADIUS server. Format radius server attribute 4 Mode Global Config 11.3.2 no radius server attribute 4 This command is used to reset the NAS - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 204
but additionally provides for separate authentication, authorization, and accounting services. The original protocol was UDP based with messages passed in enters into the TACACS+ configuration mode. The parameter is the IP address or hostname of the TACACS+ server. To specify - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 205
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 11.4.3 tacacs-server key This command is used to set the authentication and encryption key for all TACACS+ communications between the switch and the TACACS+ daemon. The parameter has a range of 0 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 206
. Format timeout Mode TACACS Config 11.4.11 show tacacs This command is used to display the configuration and statistics of a TACACS+ server. Format show tacacs Mode Privileged EXEC 11-24 Port-Based Access and Authentication Commands v4.1, October 2008 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 207
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, IP-Address| Hostname Port Timeout Priority Port The IP address or the DNS name of the configured TACACS+ server. range from 0 to 65535 connection timeout range from 0 to 65535 range from 0 to 65535 Port- - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 208
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 11-26 Port-Based Access and Authentication Commands v4.1, October 2008 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 209
which increases fault tolerance and provides load sharing. The LAG feature initially load shares traffic based upon the source and destination MAC address. The Port-Channel/LAG Command section includes the following topics: • Section 12.1 "Port-Channel Configuration Commands" on page 1 • Section 12 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 210
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 12.1.1 addport This command adds one port to the port-channel (LAG). The first interface is a logical unit, slot and port number of a configured port-channel. Note: Before adding a port to a port-channel, set - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 211
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 12.1.4.1 no port-channel This command deletes a port-channel (LAG). Format no port-channel { | all} Mode Global Config 12.1.5 clear port-channel Use this command to clear all - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 212
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 12.1.8 port-channel adminmode This command enables a port-channel (LAG). The option all sets every configured portchannel with the same administrative mode setting. Format port-channel adminmode [all] Mode - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 213
mode range is in the range 1-6 as follows: 1. Source MAC, VLAN, EtherType, and port ID 2. Destination MAC, VLAN, EtherType, and port ID 3. Source IP and source TCP/UDP port 4. Destination IP and destination TCP/UDP port 5. Source/Destination MAC, VLAN, EtherType and port 6. Source/Destination - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 214
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 12.2.1 show port-channel This command displays the static capability of all port-channels (LAGs) on the device as well as a summary of individual port-channels. Format show port-channel Modes Privileged - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 215
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, Mbr Ports Port Speed Type Active Ports Enable - Spanning tree is enabled for this port. A listing of the ports that are members of this port-channel (LAG), in unit/slot/port notation. There can be a maximum - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 216
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 12-8 Port-Channel/LAG (802.3ad) Commands v4.1, October 2008 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 217
Section 13.4 "DiffServ Policy Commands" on page 16 • Section 13.5 "DiffServ Service Commands" on page 21 • Section 13.6 "DiffServ Show Commands" on page 22 MAC Access Control List (ACL) Commands" on page 29 • Section 13.8 "IP Access Control List (ACL) Commands" on page 33 The commands in this section - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 218
Interface Config 13.1.2.1 no classofservice ip-precedence-mapping This command maps an IP precedence value to a default internal traffic class value Format no classofservice ip-precedence-mapping Modes Global Config Interface Config 13-2 Quality of Service (QoS) Commands v4.1, October 2008 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 219
.1.4 classofservice trust This command sets the class of service trust mode of an interface. You can set the mode to trust one of the Dot1p (802.1p), IP DSCP, or IP Precedence packet markings. Format classofservice trust Mode Global Config Interface Config 13 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 220
specifies the minimum transmission bandwidth guarantee for each interface queue. The total number of queues supported per interface is platform specific. A value from 0-100 (percentage of link rate) the transmitted traffic rate is bounded. 13-4 Quality of Service (QoS) Commands v4.1, October 2008 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 221
for a specific interface. The unit/slot/port parameter is optional and is only valid on platforms that support independent per-port class of service mappings. If specified, the IP Precedence mapping table of the interface is displayed. If omitted, the most recent global configuration settings are - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 222
to which the IP DSCP value is mapped. 13.1.11 show classofservice trust This command displays the current trust mode setting for a specific interface. The unit/ slot/port parameter is optional and is only valid on platforms that support independent perport class of service mappings. If specified - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 223
show interfaces cos-queue [unit/slot/port] Privileged EXEC An interface supports n queues numbered 0 to (n-1). The specific n value is platform . 13.2 Differentiated Services (DiffServ) Commands This section describes the commands you use to configure QOS Differentiated Services (DiffServ). You - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 224
of one referenced (nested) class • Class definitions do not support hierarchical service policies A given class definition can contain a maximum of CoS, IP DSCP, and IP Precedence. While the latter two are only meaningful for IP packet types, CoS marking is allowed for both IP and non-IP packets, - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 225
to inactive. While disabled, the DiffServ configuration is retained and can be changed, but it is not activated. When enabled, Diffserv services are activated. Format no diffserv Mode Global Config 13.3 DiffServ Class Commands Use the DiffServ class commands to define traffic classification. To - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 226
or as a custom ethertype value in the range of 0x0600-0xFFFF. Format match ethertype { | custom } Mode Class-Map Config 13-10 Quality of Service (QoS) Commands v4.1, October 2008 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 227
DiffServ class whose match conditions are being referenced by the specified class definition. Format no match class-map Mode Class-Map Config Quality of Service (QoS) Commands v4.1, October 2008 13-11 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 228
command adds to the specified class definition a match condition for the Class of Service value (the only tag in a single tagged packet or the first or outer the destination IP address of a packet. The parameter specifies an IP address. The parameter specifies an IP address bit mask - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 229
the value for is one of the supported port name keywords. The currently supported values are: domain, echo, ftp, Service Type octet in the IP header (the low-order five bits are not checked). The precedence value is an integer from 0 to 7. Note: The ip dscp, ip precedence, and ip - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 230
condition using a single keyword notation, the value for is one of the supported protocol name keywords. The currently supported values are: icmp, igmp, ip, tcp, udp. A value of ip is matches all protocol number values. 13-14 Quality of Service (QoS) Commands v4.1, October 2008 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 231
based on the source IP address of a packet. The parameter specifies an IP address. The parameter specifies an IP address bit mask and must consist for is one of the supported port name keywords (listed below). Quality of Service (QoS) Commands v4.1, October 2008 13-15 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 232
for the ProSafe 7300S Series Layer-3 Stackable Switches, The currently supported values are: domain, echo, ftp, ftpdata, http policy attributes. Assign the class/policy association to an interface to form a service. Specify the policy name when you create the policy. Each traffic class - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 233
at any time. If the policy is currently referenced by one or more interface service attachments, this delete attempt fails. Format no policy-map Mode Global Config n is the number of egress queues supported by the device. Quality of Service (QoS) Commands v4.1, October 2008 13-17 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 234
the name of an existing DiffServ class. Note: This command causes the specified policy to create a reference to the class definition. 13-18 Quality of Service (QoS) Commands v4.1, October 2008 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 235
command marks all packets for the associated traffic stream with the specified class of service value in the priority field of the 802.1p header (the only tag in Class-Map Config Incompatibilities Drop, Mark IP DSCP, IP Precedence, Police Quality of Service (QoS) Commands v4.1, October 2008 13-19 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 236
ip-dscp This command marks all packets for the associated traffic stream with the specified IP ip-dscp Mode Policy-Class-Map Config Incompatibilities Drop, Mark CoS, Mark IP Precedence, Police 13.4.8 mark ip , ef. For set-prec-transmit, an IP Precedence value is required. It is an - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 237
direction. The parameter is the name of an existing DiffServ policy; it is defined by the Policy-Map command. This command causes a service to create a reference to the policy. Note: This command effectively enables DiffServ on an interface in the inbound direction. There is no separate - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 238
. The parameter is the name of an existing DiffServ policy; it is defined by the Policy-Map command. Note: This command causes a service to remove its reference to the policy. This command effectively disables DiffServ on an interface in the inbound direction. There is no separate - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 239
Match Criteria fields are: Destination IP Address, Destination Layer 4 Port, Every, IP DSCP, IP Precedence, IP TOS, Protocol Keyword, Reference Class,Source IP Address, and Source Layer 4 Port. takes no options. Format show diffserv Quality of Service (QoS) Commands v4.1, October 2008 13-23 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 240
Table Size Policy Table Max Policy Instance Table Size Policy Instance Table Max Policy Attribute Table Size Policy Attribute Table Max Service Table Size Service Table Max Privileged EXEC The current value of the DiffServ administrative mode. The current number of entries (rows) in the Class - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 241
supported IP Precedence mark value if the conform action is set-prec-transmit. Drop Drop a packet upon arrival. This is useful for emulating access control list operation using DiffServ, especially when DiffServ and ACL cannot co-exist on the same interface. Mark CoS Denotes the class of service - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 242
ip description is not specified. Denotes the mark/re-mark value used as the IP Precedence for traffic matching this class. This is not displayed if mark ip Non-Conform IP Precedence Value field displays the IP Precedence mark supported). Class Members List of all class names associated with this - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 243
the specified interface and direction. The parameter specifies a valid unit/slot/port number for the system. Format show diffserv service in Mode Privileged EXEC DiffServ Admin Mode The current setting of the DiffServ administrative mode. An attached policy is - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 244
Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, OperStatus Policy Name The current operational status of this DiffServ service interface. The name of the policy attached to the interface in the indicated direction. 13.6.6 show policy-map interface This command - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 245
Operational Status The current operational status of this DiffServ service interface. Policy Name The name of the policy attached type. • The system supports only Ethernet II frame types. • The maximum number of rules per IP ACL is hardware dependent. • If you configure an IP ACL on an interface - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 246
to the list of configured rules for the list. Note: The 'no' form of this command is not supported since the rules within a MAC ACL cannot be deleted individually. Instead, you must delete and respecify the entire form aa:bb:cc:dd:ee:ff. 13-30 Quality of Service (QoS) Commands v4.1, October 2008 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 247
hexadecimal value from 0x0600-0xFFFF. The currently supported values are: appletalk, arp Ethernet layer 2 packets, and is the equivalent of the IP access list "match every" rule. Format Mode {deny|permit Access-List Config Quality of Service (QoS) Commands v4.1, October 2008 13-31 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 248
mode setting is applied to all interfaces. The 'Interface Config' mode command is only available on platforms that support independent per-port class of service queue configuration. Format mac access-group in [sequence ] Modes Global Config Interface Config 13.7.4.1 no mac - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 249
to specific resources and block any unwarranted attempts to reach network resources. The following rules apply to IP ACLs: • The 7300S Series Stackable Switch does not support IP ACL configuration for IP packet fragments. • The maximum number of ACLs you can create is 100, regardless of type. • The - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 250
port range. The command specifies a destination IP address and destination mask for match condition of the IP ACL rule specified by the dstip and specifies the TCP flags for an IP ACL rule depending on a TCP flag match. Supported options are: • URG (Urgent Service (QoS) Commands v4.1, October 2008 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 251
that is one greater than the highest sequence number currently in use for this interface and direction is used. Default none Format ip access-group in [sequence ] Modes Interface Config Global Config Quality of Service (QoS) Commands v4.1, October 2008 13-35 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 252
port for this rule. Destination IP Address This displays the destination IP address for this rule. Destination IP Mask This field displays the destination IP Mask for this rule. Destination Ports This field displays the destination port for this rule. Service Type Field Match This field - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 253
ProSafe 7300S Series Layer-3 Stackable Switches, 13.8.4 show access-lists This command displays IP ACLs and MAC access control lists information for a designated interface and direction. Format is used. Valid range is (1 to 4294967295). Quality of Service (QoS) Commands v4.1, October 2008 13-37 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 254
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 13-38 Quality of Service (QoS) Commands v4.1, October 2008 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 255
Protocol (ARP) Commands This section describes the commands you use to configure ARP and to view ARP information on the switch. ARP associates IP addresses with MAC addresses and stores the information as ARP entries in the ARP cache. 14.1.1 arp This command creates an ARP entry. The value for - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 256
. Format no arp Mode Global Config 14.1.2 ip proxy-arp This command enables proxy ARP on a router interface. Without proxy ARP, a device only responds to an ARP request if the target IP address is an address configured on the interface where the ARP request arrived. With - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 257
dynamic ARP entries from renewing when they age out. Format no arp dynamicrenew Mode Privileged EXEC 14.1.5 arp purge This command causes the specified IP address to be removed from the ARP cache. Only entries of type dynamic or gateway are affected by this command. Format arp purge - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 258
Config 14.1.8 arp timeout This command configures the ARP entry ageout time. The value for is a valid positive integer, which represents the IP ARP entry ageout time in seconds. The range for is between 15-21600 seconds. Default 1200 Format arp timeout Mode - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 259
in the ARP table. The following fields are displayed for each ARP entry. IP Address Is the IP address of a device on a subnet attached to an exist- ing routing interface. MAC Address Is the hardware MAC address of that device. Interface Type Age Is the routing unit/slot/port associated with - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 260
, 14.1.11 show arp brief This command displays the brief Address Resolution Protocol (ARP) table information. Format show arp brief Mode count in the ARP table. 14.2 IP Routing Commands This section describes the commands you use to enable and configure IP routing on the switch. 14.2.1 routing - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 261
enables the IP Router Admin Mode for the master switch. Format ip routing Mode Global Config 14.2.2.1 no ip routing This command disables the IP Router Admin Mode for the master switch. Format no ip routing Mode Global Config 14.2.3 ip address This command configures an IP address on an - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 262
route This command configures a static route. The is a valid ip address. The is a valid subnet mask. The is a valid IP address of the next hop router. The is an integer value from 1 to 255. The user can specify the preference value (sometimes called - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 263
Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 14.2.5 ip route default This command configures the default route. The value for is a valid IP address of the next hop router. The is an integer value from 1 to 255 Default preference - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 264
MTUs, they will not form an adjacency (unless OSPF has been instructed to ignore differences in IP MTU with the ip ospf mtu-ignore command.) Note: The IP MTU size refers to the maximum size of the IP packet (IP Header + IP payload). It does not include any extra bytes that may be required for Layer - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 265
Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, Format Mode ip mtu Interface Config 14.2.8.1 no ip mtu This command resets the ip mtu to the default value. Format no ip mtu Mode Interface Config 14.2.9 encapsulation This command configures the link - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 266
The computed TTL (Time to Live) of forwarding a packet from the local router to the final destination. Routing Mode Shows whether the routing mode is enabled or disabled. IP Forwarding Mode Shows whether forwarding of IP frames is enabled or disabled. This is a configured value. Maximum Next - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 267
value appears only if you configure it. Secondary IP Address Displays one or more secondary IP addresses and subnet masks for the interface. This value appears only if you configure it. Routing Mode Is the administrative mode of router interface participation. The possible values are enable or - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 268
identifying the network on the specified interface. Subnet Mask Is a mask of the network and host portion of the IP address for the router interface. Protocol Tells which protocol added the specified route. The possibilities are: local, static, OSPF or RIP. Total Number of Routes The total - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 269
Stackable Switches, For each Next Hop Next Hop Intf Next Hop IP Address The outgoing router interface to use when forwarding traffic to the next destination. The outgoing router IP address to use when forwarding traffic to the next router (if any) in the path toward the destination. 14.2.15 show - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 270
interface to use when forwarding traffic to the next destination. Next Hop IP Address Metric Preference The outgoing router IP address to use when forwarding traffic to the next router (if any) in the path toward the destination. The cost associated with this route. The administrative distance - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 271
more information about the fields that are displayed. Format show ip stats Modes Privileged EXEC User EXEC 14.3 Virtual LAN Routing no vlan routing Mode VLAN Config 14.3.2 show ip vlan This command displays the VLAN routing information for all VLANs with routing enabled. Format - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 272
for the ProSafe 7300S Series Layer-3 Stackable Switches, MAC Address used by Routing VLANs VLAN ID Logical Interface IP Address Subnet Mask Is the MAC Address associated with the internalbridge-router interface (IBRI). The same MAC Address is used by all VLAN routing interfaces. It will be - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 273
on an interface and designates the configured virtual router IP address as a secondary IP address on an interface. The parameter is the virtual router ID which has an integer value range from 1 to 255. Default none Format ip vrrp [secondary] Mode Interface Config 14 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 274
interface. Disabling the status field stops a virtual router. Format no ip vrrp mode Mode Interface Config 14.4.4 ip vrrp ip This command sets the virtual router ipaddress value for an interface. The value for is the IP Address which is to be configured on that interface for - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 275
a priority integer from 1 to 254. The parameter is the virtual router ID which has an integer value ranges from 1 to 255. Default 100 Format ip vrrp priority Mode Interface Config 14.4.7.1 no ip vrrp priority This command sets the default priority value for the virtual - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 276
This command sets the frequency, in seconds, that an interface on the specified virtual router sends a virtual router advertisement. Default 1 Format ip vrrp timers advertise Mode Interface Config 14.4.8.1 no ip vrrp timers advertise This command sets the default virtual - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 277
Packets Received Address List Errors Invalid Authentication Type Authentication Type Mismatch Packet Length Errors Represents the total number of VRRP packets received that don't pass the authentication check. Represents the total number of VRRP packets received by the virtual router with IP TTL - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 278
Interface Valid slot and port number separated by forward slashes. VRID Represents the router ID of the virtual router. IP Address The virtual router IP address. Mode Represents whether the virtual router is enabled or disabled. State Represents the state (Master/backup) of the virtual - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 279
Modes Privileged EXEC User EXEC IP Address This field represents the configured IP Address for the Virtual router. VMAC address Represents the VMAC address of the specified router. Authentication type Represents the authentication type for the specific virtual - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 280
inactive. Format no enable Mode Router OSPF Config 14.5.3 ip ospf This command enables OSPF on a router interface. Default disabled Format ip ospf Mode Interface Config 14.5.3.1 no ip ospf This command disables OSPF on a router interface. Format no ip ospf Mode Interface Config 14 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 281
Stackable Switches, 14.5.4 1583compatibility This command enables OSPF 1583 compatibility. Note: 1583 compatibility mode is enabled by default. If all OSPF routers in the routing domain are capable of operating according to RFC 2328, OSPF 1583 compatibility mode should be disabled. Default Format - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 282
no-summary (OSPF) This command configures the NSSA so that summary LSAs are not advertised into the NSSA. Format area nssa no-summary Mode Router OSPF Config 14.5.10 area nssa translator-role (OSPF) This command configures the translator role of the NSSA. A value of always causes the - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 283
. Format area nssa translator-stab-intv Mode Router OSPF Config 14.5.12 area range This command creates a specified area range for a specified NSSA. The is a valid IP address. The is a valid subnet mask. The LSDB type must be specified by - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 284
Stackable Switches, 14.5.13.1 no area stub This command deletes a stub area for the specified area ID. Format no area stub Mode Router OSPF Config 14.5.14 area stub summarylsa This command configures the Summary LSA mode for the stub area identified by . The Summary LSA mode - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 285
This command configures the authentication type and key for the OSPF virtual interface identified by and . The parameter is the Router ID of the neighbor. The value for is either none, simple, or encrypt. The [key] is composed of standard displayable, non-control - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 286
of the neighbor. The range for is 1 to 65535. Default 10 Format area virtual-link hello-interval Mode Router OSPF Config 14.5.18.1 no area virtual-link hello-interval This command configures the default hello interval for the OSPF virtual interface on - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 287
the transmit delay for the OSPF virtual interface on the virtual interface identified by and . The parameter is the Router ID of the neighbor. The range for is 0 to 3600 (1 hour). Default 1 Format area virtual-link transmitdelay - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 288
14.5.22 default-metric (OSPF) This command is used to set a default for the metric of distributed routes. Format default-metric Mode Router OSPF Config 14.5.22.1 no default-metric (OSPF) This command is used to set a default for the metric of distributed routes. Format no - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 289
command to specify the access list to filter routes received from the source protocol. Format distribute-list out {rip | static | connected} Mode Router OSPF Config 14.5.24.1 no distribute-list out Use this command to specify the access list to filter routes received from the source - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 290
LSDB limit for OSPF. Format no external-lsdb-limit Mode Router OSPF Config 14.5.27 ip ospf areaid This command sets the OSPF area to which the specified router interface belongs. The value for is an IP address, formatted as a 4-digit dotted-decimal number that uniquely identifies the - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 291
have not been seen before its neighbor routers declare that the router is down. The interval must be the same for all routers attached to a common network. This value should be some multiple of the Hello Interval (i.e. 4). Default 40 Format ip ospf dead-interval Mode Interface - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 292
The value for the length of time must be the same for all routers attached to a network. Valid values range from 1 to 65535. Default 10 Format ip ospf hello-interval Mode Interface Config 14.5.31.1 no ip ospf hello-interval This command sets the default OSPF hello interval for the - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 293
between link-state advertisement retransmissions for adjacencies belonging to this router interface. This value is also used when retransmitting database description the specified interface. Format no ip ospf retransmit-interval Mode Interface Config 14.5.34 ip ospf transmit-delay This command - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 294
transmission unit (MTU) mismatch detection. OSPF Database Description packets specify the size of the largest IP packet that can be sent without fragmentation on the interface. When a router receives a Database Description packet, it examines the MTU advertised by the neighbor. By default, if - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 295
the number of paths that OSPF can report for a given destination where maxpaths is platform dependent. Default 4 Format maximum-paths Mode Router OSPF Config 14.5.38.1 no maximum-paths This command resets the number of paths that OSPF can report for a given destination back to its - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 296
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 14.5.40 show ip ospf This command displays information relevant to the OSPF router. Format show ip ospf Mode Privileged EXEC Note: Some of the information below displays only if you enable OSPF and - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 297
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, New LSAs Originated LSAs Received External LSDB Limit Default Metric Default Route Advertise Always Metric Metric Type Maximum Paths Redistributing Source Metric Metric Type Tag Subnets Distribute-List Shows - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 298
identifies the OSPF area that is being displayed. Format show ip ospf area Modes Privileged EXEC User EXEC AreaID Is the area this area's link-state database. Area Border Router Count The total number of area border routers reachable within this area. Area LSA Count Total - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 299
LSA checksum. This is an integer. It indicates that the LSA receives special handling during routing calculations. Router Options are valid for router links only. 14.5.43 show ip ospf interface This command displays brief information for the IFO object or virtual interface tables. Format show - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 300
the specified interface. Subnet Mask A mask of the network and host portion of the IP address for the OSPF interface. OSPF Admin Mode States whether OSPF is enabled or disabled on a router interface. OSPF Area ID Represents the OSPF Area Id for the specified interface. 14-46 v4.1, October - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 301
are: down, loopback, waiting, point-to-point, designated router, and backup designated router. Designated Router The router ID representing the designated router. Backup Designated Router The router ID representing the backup designated router. Number of Link Events The number of link events - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 302
be displayed if OSPF is enabled. Format show ip ospf interface stats Modes Privileged routers reachable within this area. Area LSA Count The total number of link-state advertisements in this area's link-state database, excluding AS External LSAs. IP Address The IP address - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 303
ospf neighbor { | all} Modes Privileged EXEC User EXEC Router ID A 4 digit dotted decimal number representing the neighbor interface. IP Address An IP address representing the neighbor interface. Neighbor Interface Index Is a unit/slot/port identifying the neighbor interface - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 304
has a neighbor. The parameter is the IP address of the neighbor. Format show ip ospf neighbor Modes Privileged EXEC User EXEC Interface Valid slot and port number separated by forward slashes.. Router Id Is a 4-digit dotted-decimal number identifying - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 305
) in the Exchange state. Full - the neighboring routers are fully adjacent and they will now appear in router-LSAs and network-LSAs. The number of times this Area ID The area id of the requested OSPF area. IP Address An IP Address which represents this area range. Subnet Mask A valid subnet - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 306
on the switch. Format show ip ospf stub table Modes Privileged EXEC User EXEC Area ID Is a 32-bit identifier for the created stub area. Type of Service Is the type of service associated with the stub metric. The 7300S Series Stackable Switch only supports Normal TOS. Metric Val The - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 307
information for a specific area and neighbor. The parameter identifies the area and the parameter identifies the neighbor's Router ID. Format show ip ospf virtual-link Modes Privileged EXEC User EXEC Area ID The area id of the requested OSPF area - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 308
to inactive. Format no enable Mode Router RIP Config 14.6.3 ip rip This command enables RIP on a router interface. Default disabled Format ip rip Mode Interface Config 14.6.3.1 no ip rip This command disables RIP on a router interface. Format no ip rip Mode Interface Config 14-54 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 309
RIP Config 14.6.6 default-metric (RIP) This command is used to set a default for the metric of distributed routes. Format default-metric Mode Router RIP Config 14.6.6.1 no default-metric (RIP) This command is used to reset the default metric of distributed routes to its default value - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 310
to specify the access list to filter routes received from the source protocol. Default 0 Format distribute-list out {ospf | static | connected} Mode Router RIP Config 14.6.8.1 no distribute-list out This command is used to specify the access list to filter routes received from the - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 311
format, or none to not allow any RIP control packets to be received. Default both Format ip rip receive version {rip1 | rip2 | both | none} Mode Interface Config 14.6.10.1 no ip rip receive version This command configures the interface to allow RIP control packets of the default version - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 312
control packets of the default version to be sent. Format no ip rip send version Mode Interface Config 14.6.12 hostroutesaccept This command enables RIP hostroutesaccept mode. Default enabled Format hostroutesaccept Mode Router RIP Config 14.6.12.1 no hostroutesaccept This command - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 313
-3 Stackable Switches, 14.6.13 split-horizon This command sets the RIP split horizon mode. Default simple Format split-horizon {none | simple | poison} Mode Router RIP Config 14.6.13.1 no split-horizon This command sets the default RIP split horizon mode. Format no split-horizon Mode - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 314
This command displays information relevant to the RIP router. Format show ip rip Modes Privileged EXEC User EXEC RIP Admin Mode Enable or disable. Split Horizon Mode None, simple or poison reverse. Split horizon is a technique for avoiding problems caused by including routes in updates sent - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 315
types are none, RIP-1, RIP-2, Both RIP Mode RIP administrative mode of router RIP operation; enable activates, disable de-activates it. Link State The separated by forward slashes. This is a configured value. IP Address The IP source address used by the specified RIP interface. This is a - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 316
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, Link State Indicates whether the RIP interface is up or down. This is a configured value. Authentication Type The RIP Authentication Type for the specified interface. The types are none, simple, and encrypt - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 317
in the 7300S Series Stackable Switch CLI. The 7300S Series Stackable Switch supports IGMP Versions 1, 2, and 3. The IGMP snooping feature can help section describes the commands you use to configure IGMP snooping. 15.1.1 ip igmpsnooping This command enables IGMP Snooping on the system (Global Config - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 318
. The IGMP application supports the following activities: • Validation of the IP header checksum (as well as the IGMP header checksum) and discarding of the frame upon checksum error. • Maintenance of the forwarding table entries based on the MAC address versus the IP address. • Flooding of - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 319
time value. The range is 2 to 3600 seconds. Default 260 seconds Format ip igmpsnooping groupmembership-interval Modes Interface Config Global Config VLAN Mode 15.1.3.1 no ip igmpsnooping groupmembership-interval This command sets the IGMPv3 Group Membership Interval time to - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 320
time (on the interface or VLAN) to the default value. Format no ip igmpsnooping maxresponse Modes Global Config Interface Config VLAN Mode 15.1.5 ip igmpsnooping mcrtexpiretime This command sets the Multicast Router Present Expiration time. The time is set for the system, on a particular - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 321
This command disables the forwarding of IGMP packets to this interface. Format no ip igmp mrouter Mode Interface Config 15.1.7 ip igmp mrouter interface This command configures the interface as the one the multicast router is attached to. All IGMP packets snooped by the switch will be - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 322
multicast router via this interface. Format no ip igmp mrouter interface Mode Interface Config 15.1.8 ip address in the destination field will be dropped. This command is mainly used when IGMP snooping is enabled, to prevent flooding of unwanted multicast packets to every port. Format ip - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 323
Time Displays the amount of time to wait before removing an interface that is participating in the VLAN from the list of interfaces with multicast routers attached. The interface is removed if a query is not received. This value may be configured. IGMP Snooping Commands v4.1, October 2008 15 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 324
ports. Format show ip igmp mrouter vlan Mode Privileged EXEC Interface Shows the port on which multicast router information is being displayed. VLAN ID Displays the list of VLANs of which the interface is a member. 15.2.4 show mac-address-table igmpsnooping This command - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 325
supports router is not attached. • Must not be the probe port of a mirroring session. • Must not be a LAG member. • Must not be enabled for routing. • Must be in the Forwarding state. The query packets that are sent periodically will have one of the following IP addresses for the source IP address - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 326
be 0.0.00, no query packets are sent. If multiple IGMP queriers reside on the VLAN the switch with lower IP address will remain active. Note that if the other querier is a multicast router it will continue sending queries and will not back off. The interval for the IGMP queries sent by the switch - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 327
Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 15.3.3 ip igmpsnooping querier query-interval To configure the IGMP querier query interval for a VLAN , use the ip igmpsnooping querier query-interval command. Valid range for is 1 to - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 328
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 15-12 v4.1, October 2008 IGMP Snooping Commands - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 329
. PoE supplies reliable, uninterrupted power to Internet Protocol (IP) telephones, wireless LAN access points, and other Ethernet devices that use An integrated power-data network solves that problem and allows greater flexibility and range in wireless networking. In order for the network to - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 330
to support this watts. IP phones and wireless LAN service (QoS) where key users are given higher priority to power in the event of a outage. Voice-over IP (VoIP), is the transmission of telephone calls over a data network like one of the many networks that make up the Internet. Other NETGEAR - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 331
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 16.1.1 poe This command enables or disables the Power over Ethernet function on the specified port(s). Default enable Format poe Mode Global Config 16.1.2 poe priority This command sets the priority - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 332
. Default 80 Format poe usagethreshold Mode Global Config 16.1.5 show poe port info This command displays a summary for the ports that support the PoE function. Format show poe port Mode Privilege The following fields are displayed for each port. If a port - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 333
Fault-the POE device is not IEEE compliance, no power is provided • Test-the port is in testing state • Other Fault-the port has experience problems other than compliance issue When a port begins to deliver power, there will be a trap indicating so. When a port stops delivering power, there will be - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 334
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 16-6 v4.1, October 2008 Power Over Ethernet Commands - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 335
Chapter 17 Stacking Commands This section describes the stacking commands available in the 7300S Series Stackable Switch CLI. The Stacking Commands section includes the following topics: • Section 17.1 "Dedicated Port Stacking" on page 1 • Section 17.2 "Front Panel Stacking Commands" on page 10 The - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 336
is the switch identifier of the switch to be added/removed from the stack. The is the index into the database of the supported switch types, indicating the type of the switch being preconfigured. The switch index is a 32-bit integer. This command is executed on the Primary - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 337
system:running-config nvram:startup-config (in Privileged EXEC) command before performing the stack move. A stack move causes all routes and layer 2 addresses to be lost. This command is executed on the Primary Management Unit. The administrator is prompted to confirm the management move. Format - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 338
of the slot. The is the index into the database of the supported card types, indicating the type of the card being preconfigured in the specified slot. Config Note: Card index can be obtained by executing show supported cardtype command in User EXEC mode. 17.1.8.1 no slot This - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 339
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 17.1.9 set slot disable This command configures the administrative mode of the slot(s). If you specify [all], the command is applied to all slots, otherwise the command is applied to the slot identified by < - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 340
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 17.1.10.1 no set slot power This command unconfigures the power mode of the slot(s) and prohibits power from being supplied to a card located in the slot. If you specify [all], the command prohibits power to - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 341
If you do not supply a value for [cardindex], the following output appears: Card Index (CID) This field displays the index into the database of the supported card types. This index is used when preconfiguring a slot. Card Model Identifier The model identifier for the - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 342
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 17.1.14 show switch This command displays information about all units in the stack or a single unit when you specify the unit value. Format show switch [unit] Mode Privileged EXEC Switch The unit - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 343
, then the code version is "None". The system up time. 17.1.15 show supported switchtype This commands displays information about all supported switch types or a specific switch type. Format show supported switchtype [switchindex] Mode User EXEC Stacking Commands v4.1, October 2008 17-9 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 344
do not supply a value for [switchindex], the following output appears: Switch Index (SID) This field displays the index into the database of supported switch types. This index is used when preconfiguring a member to be added to the stack. Model Identifier This field displays the model identifier - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 345
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 17.2.2 qos-mode This command enables QOS mode for front panel stacking. Default enabled Format qos-mode Mode Stack Global Config 17.2.2.1 no qos-mode This command disables QOS mode for front panel - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 346
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 17.2.4 show stack-port counters This command displays summary data counter information for all interfaces. Format show stack-port counters Mode Privileged EXEC Unit Displays the unit number. Interface - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 347
Chapter 18 LLDP and LLDP-MED Commands This section describes the LLDP and LLDP-MED commands available in the 7300S Series Stackable Switch CLI. The commands section includes the following topics: • Section 18.1 "LLDP Commands" on page 1 • Section 18.2 "LLDP-MED Commands" on page 9 18.1 LLDP - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 348
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, Format Mode lldp receive Interface Config 18.1.4 no lldp receive This command is used to return the reception of LLDPDUs to the default. Format no lldp receive Mode Interface Config 18.1.5 lldp timers - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 349
] [sys-cap] [port-desc] Mode Interface Config 18.1.9 lldp transmit-mgmt This command is used to include transmission of the local system management address information in the LLDPDUs. Format lldp transmit-mgmt Mode Interface Config 18.1.10 no lldp transmit-mgmt Use this command to cancel - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 350
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, Format Mode lldp notification-interval Global Config 18.1.14 no lldp notification-interval This command is used to return the notification interval to the default value. Format no lldp - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 351
can be 0 (Port Description), 1 (System Name), 2 (System Description), or 3 (System Capability). Mgmt Shows whether the interface transmits system management address information in the LLDPDUs. 18.1.19 show lldp statistics This command displays the current LLDP traffic and remote table statistics - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 352
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, Transmit Total Receive Total Discards Errors Ageouts TVL Discards TVL Unknowns TVL MED TVL 802.1 TVL 802.3 Total number of LLDP packets transmitted on the port. Total number of LLDP packets received on the - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 353
the port in an alpha-numeric format. The port description is configurable. Indicates the primary function(s) of the device. Shows which of the supported system capabilities are enabled. The amount of time (in seconds) the remote device's information received in the LLDPDU should be treated as valid - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 354
the port in an alpha-numeric format. Indicates the primary function(s) of the device. Shows which of the supported system capabilities are enabled. The type of address and the specific address the local LLDP agent uses to send and receive information. 18-8 v4.1, October 2008 LLDP and LLDP-MED - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 355
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 18.2 LLDP-MED Commands 18.2.1 lldp med This command is used to enable the MED of LLDP advertise capability. The command is available in the interface configuration mode. The 'all' option is also available in - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 356
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 18.2.4 no lldp med confignotification This command is used to disable notifications. The 'all' option is also available in the Global config mode to disable on all the ports. Format no lldp med - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 357
Communicatin Controller etc.], Class II Media Conference Bridge etc.], Class III Communication [IP Telephone etc.]. The fourth device is Network Connectivity Device, which is typically a LAN Switch/Router, IEEE 802.11 Wireless Access Point etc. 18.2.10 show lldp med interface This command displays - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 358
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, OperMED ConfigNotify TLVsTx Shows if the LLPD-MED TLVs are transmitted or not on this interface. Shows if the LLPD-MED topology notification mode of this interface. Shows whether the interface sends optional - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 359
IP Telephone etc]). The fourth device is Network Connectivity Device, which is typically a LAN Switch/Router, IEEE 802.1 Bridge, IEEE 802.11 Wireless /port> ] Mode Privileged EXEC Supported Capabilities Enabled Capabilities Device Class Shows the supported capabilities that was received in MED - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 360
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, Media Application Type VLAN Id Priority DSCP Unknown Tagged Shows the application type. Types of applications are unknown, voice, voicesignaling, guestvoice, guestvoicesignaling, sfotphonevoice, - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 361
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, Available Source Priority Shows the romote port's PSE power value in tenths of a watt. Shows the remote port's PSE power source. Shows the remote port's PSE priority. Required Source Priority Shows the - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 362
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 18-16 v4.1, October 2008 LLDP and LLDP-MED Commands - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 363
. 19.1.1 show arp switch This command displays connectivity between the switch and other devices. The Address Resolution Protocol (ARP) cache identifies the MAC addresses of the IP stations communicating with the switch. Format show arp switch System Maintenance Commands v4.1, October 2008 19 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 364
/or filtering information. The format is 6 two-digit hexadecimal numbers that are separated by colons, for example 01:23:45:67:89:AB The IP address assigned to each interface. Valid slot and port number separated by forward slashes. 19.1.2 show eventlog This command displays the event log, which - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 365
ProSafe 7300S Series Layer-3 Stackable Switches, Machine Model Serial Number FRU Number Part Number Maintenance Level Manufacturer Burned in MAC Address Software Version Operating System Network Processing Device Additional Packages Specifies the machine model as defined by the Vital Product Data - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 366
errors preventing them from being deliverable to a higher-layer protocol. The total number of packets received that were directed to the broadcast address. Note that this does not include multicast packets. Total number of packets transmitted out the interface. Number of outbound packets that could - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 367
were discarded or not sent. The number of outbound packets that could not be transmitted because of errors. The total number of Forwarding Database Address Table entries now active on the switch, including learned and static entries. The number of VLAN entries presently occupying the VLAN table. The - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 368
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, StatsPkts and etherStatsOctets objects should be sampled before and after a common interval. The result of this equation is the value Utilization which is the percent utilization of the Ethernet segment on a - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 369
. Multicast Packets Received - The total number of good packets received that were directed to a multicast address. Note that this number does not include packets directed to the broadcast address. Broadcast Packets Received - The total number of good packets received that were directed to the - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 370
in the multicast tree for a VLAN occurs while that tree is being modified. Reserved Address Discards - The number of frames discarded that are destined to an IEEE 802.1 reserved address and are not supported by the system. Broadcast Storm Recovery - The number of frames discarded that are destined - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 371
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, Packets Transmitted Octets Upstream Threshold - The number of frames discarded due to lack of cell descriptors available for that packet's priority level. Total Bytes - The total number of octets of data ( - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 372
discarded or not sent. Broadcast Packets Transmitted - The total number of packets that higher-level protocols requested be transmitted to the Broadcast address, including those that were discarded or not sent. Total Errors - The sum of Single, Multiple, and Excessive Collisions. Tx FCS Errors - The - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 373
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, Protocol Statistics Multiple Collision Frames - A count of the number of successfully transmitted frames on a particular interface for which transmission is inhibited by more than one collision. Excessive - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 374
. Multicast Packets Received - The total number of packets received that were directed to a multicast address. Note that this number does not include packets directed to the broadcast address. Broadcast Packets Received - The total number of packets received that were directed to the broadcast - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 375
were discarded or not sent. Broadcast Packets Transmitted - The total number of packets that higher-level protocols requested be transmitted to the Broadcast address, including those that were discarded or not sent. Transmit Packets Discarded - The number of outbound packets which were chosen to be - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 376
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, Time Since Counters Last Cleared VLAN Deletes - The number of VLANs on this switch that have been created and then deleted since the last reboot. The elapsed time, in days, hours, minutes, and seconds, since - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 377
on that VLAN are reported. Format show mac-addr-table [ | | VLAN | all] Mode Privileged EXEC Mac Address A unicast MAC address for which the switch has forwarding and or filtering information. The format is 6 or 8 two-digit hexadecimal numbers that are separated by - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 378
19.1.8 clear mac-addr-table This command clears the dynamically learned MAC addresses of the switch. Format clear mac-addr-table Mode Privileged EXEC 19 to display/capture the current setting of different protocol packages supported on the switch. This command displays/captures commands with - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 379
The base object ID for the switch's enterprise MIB. System Up Time The time in days, hours and minutes since the last switch reboot. MIBs Supported A list of MIBs supported by this agent. System Maintenance Commands v4.1, October 2008 19-17 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 380
This section describes the commands you use to help troubleshoot connectivity issues and to restore various configurations to their factory the network on a hop-by-hop basis. The value should be a valid IP address. The [port] value should be a valid decimal integer in the range of 0(zero - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 381
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 19.2.5 clear pass This command resets all user passwords to the factory defaults without powering off the switch. You are prompted to confirm that the password reset should proceed. Format clear pass Mode - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 382
source or destination, use one of the following values: xmodem | ymodem | zmodem | tftp://// For TFTP, the parameter is the IP address of the server, is the path to the file, and is the name of the file you want to upload or download - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 383
for network (in-band) connection. The source and target devices must have the ping utility enabled and running on top of TCP/IP. You can ping the switch from any IP workstation the switch is connected to through the default VLAN (VLAN 1), as long as there is a physical path between the switch - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 384
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 19.2.13 reload This command resets the switch without powering it off. Reset means that all network connections are terminated and the boot code executes. The switch uses the stored configuration to - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 385
console Mode Global Config 19.3.4 logging host This command enables logging to a host. You can configure up to eight hosts. The is the IP address of the logging host. The value is a port number from 1 to 65535. You can specify the value as either an integer from - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 386
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, Format Mode logging host remove Global Config 19.3.6 logging port This command sets the local port number of the LOG client for logging messages. The can be in the range from 1 to 65535 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 387
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, Console Logging Administrative Mode Console Logging Severity Filter Buffered Logging Administrative Mode Buffered Logging Severity Filter Historical Logging Administrative Mode Historical Logging Severity - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 388
hosts. Format show logging hosts Mode Privileged EXEC Host Index (Used for deleting hosts) Severity Level The minimum severity to log to the specified address. Port Displays the server port number, which is the port on the local host from which syslog messages are sent. Host Status The - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 389
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 19.3.12 show logging traplogs This command displays SNMP trap events and statistics. Format show logging traplogs Mode Privileged EXEC Number of Traps Since Last Reset Shows the number of traps since the - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 390
line and ignored by the parser. The following lines show an example of a script: ! Script file for displaying the ip interface ! Display information about interfaces show ip interface 1/0/1 !Displays the information about the first interface ! Display information about the next interface show - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 391
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 19.5.1 script apply This command applies the commands in the script to the switch. The parameter is the name of the script to apply. Format script apply Mode Privileged EXEC 19 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 392
Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 19.6 Packet Capture Packet capture commands assist in troubleshooting protocol-related problems with the management CPU. The packets to and from the management CPU can be captured in an internally allocated buffer - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 393
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 19.6.3 capture all packets This command enables the capturing of both transmit and receive packets. Format capture all packets Mode Global Config 19.6.3.1 no capture all packets This command disables - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 394
for the ProSafe 7300S Series Layer-3 Stackable Switches, 19.7 Dumping System Information The show tech-support command dumps all major system information into a file that can be sent to NETGEAR product support for debugging purposes. The command output is not displayed on the console. Use the copy - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 395
138) • TACACS Server (port 49) • Time Service (port 37) The system supports a maximum of 128 interface address-port pairs. For example, you can have a single a broadcast UDP packet on a routing interface, the UDP port to IP address mapping table is checked. If that routing interface has an entry, the - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 396
.1 UDP Relay Configuration Commands This section describes configuration commands for setting up UDP relay service. 20.1.1 ip helper-address (global config mode) Use the Global Configuration ip helper-address command to have the switch forward User Datagram Protocol (UDP) broadcasts received on an - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 397
addresses, use the no form of this command. Format ip helper-address ip-address [udp-port-list] no ip helper-address ip-address Parameters ip-address Destination broadcast or host address , packets for the default services are forwarded to the helper address. Mode Interface Config 20.2 - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 398
Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 20-4 v4.1, October 2008 UDP Relay Commands - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 399
show igmpsnooping show mac-address-table igmpsnooping show ip brief show ip show ip interface brief show ip interface show ip ospf interface brief show ip ospf interface show ip ospf neighbor brief show ip ospf neighbor show ip ospf neighbor brief all - Netgear GSM7328Sv1 | CLI Reference Manual for 7300S Series Layer-3 Stackable Swi - Page 400
multiusers snmp-server enable traps stpmode speed all 1000 full-duplex set igmp 5.0.1.9 (or newer) Equivalent Command ip igmpsnooping maxresponse ip igmpsnooping minresponse snmp-server traps snmp-server traps bcaststorm snmp-server traps linkmode snmp-server traps multiusers
202-10237-05
October 2008
NETGEAR
, Inc.
350 Plumeria Dr.
San Jose, CA 95124 USA
Command Line Interface
Reference for the ProSafe
7300S Series Layer-3
Stackable Switches,
Software Version 7.3