Netgear M6100-44G3-POE Software Setup Manual Software Version 11.x
Netgear M6100-44G3-POE Manual
View all Netgear M6100-44G3-POE manuals
Add to My Manuals
Save this manual to your list of manuals |
Netgear M6100-44G3-POE manual content summary:
- Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 1
M6100, M5300, and M7100 Series Switches Software Setup Manual Software Version 11.0.0 March 2015 208-10798-01 350 East Plumeria Drive San Jose, CA 95134 USA - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 2
M6100, M5300, and M7100 Series Switches Support Thank you for selecting NETGEAR products. After list of phone numbers at http://support.netgear.com/general/contact/default.aspx. Contact your Internet service provider for technical support. Compliance For regulatory compliance information, - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 3
for Initial Configuration 14 Overview of the Web Management Interface 14 Use the Web Management Interface to Configure the Management VLAN Interface and Service Port 15 Access the Web Management Interface When the Switch Is Already Connected to the Network 17 Configure an SNMPv3 User Profile - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 4
M6100, M5300, and M7100 Series Switches Activate a License Key for a Switch 30 Load the License File onto the Switch 31 Use the CLI to Load a License 31 Use the Web Management Interface to Load a License 31 4 - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 5
• Use the Management VLAN Interface, Service Port, or Console Port for Initial Configuration • Use the Web Management Interface for Initial Configuration Note: For more information about the topics covered in this manual, visit the support website at support.netgear.com. Note: Firmware updates with - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 6
, M5300, M7100 Software Administration Manual • M6100, M5300, M7100 Web User Guide Overview of the Access and Initial Configuration Options To configure the switch, you can access it through the console port, management VLAN interface, service port, or web management interface. For information about - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 7
M6100, M5300, and M7100 Series Switches You can access the console port of the switch either through a mini-USB port or through the serial port: • Mini- - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 8
options, see the M4100, M5300, and M6100 Command Line Interface Manual that is available at downloadcenter.netgear.com. If the POST detects a critical problem, the startup procedure stops. The boot : Only switch model M6100 supports a service port. This service port is on the M6100 front panel and is - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 9
M6100, M5300, and M7100 Series Switches • ezconfig. Use the ezconfig application through the management VLAN interface, service port, or console an IP address to the switch through DHCP, the default IP address for the service port is 169.254.101.100 and the default IP address for the management VLAN - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 10
to assign an IP address manually. Enter one of the following commands: • For the management VLAN interface: (Management Switch) #config (Management Switch) (Config)#interface VLAN 1 (Management Switch) (Interface vlan 1)#no ip address dhcp • For the service port: serviceport protocol none 4. Set - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 11
M6100, M5300, and M7100 Series Switches Use ezconfig for Initial Configuration You can perform the initial configuration by using the Easy Setup Wizard (ezconfig) through the management VLAN interface, service port, or console port. ezconfig Overview ezconfig is an interactive utility that provides - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 12
M6100, M5300, and M7100 Series Switches The 'enable' password required for switch to set up the IP address of the switch. 4. Set up the IP address of the switch, either manually (type C) or through DHCP (type D): Assigning an IPv4 address to your switch management Current IPv4 Address Configuration - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 13
M6100, M5300, and M7100 Series Switches overwrite the DHCP client mode by ? - Help. (C/D/A/N/Q/?) 6. To set up an IPv4 address for service port, type Y to assign the IPv4 address manually. Current Out of Band(service port) IPv4 Address Configuration IP Address Assignment Mode: DHCP IP Address: 172 - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 14
: None IPv6 Administrative Mode: Enabled Service port IPv6 Address Mode autoconfigure: Disabled IPv6 Address: fe80::6eb0:ceff:fef9:f6e1/64 Network IPv6 address gateway: IPv6 Default Router: fe80::222:3fff:fe9e:9605 EUI Flag: True The IPv6 address has been assigned manually. What do you want to do - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 15
M6100, M5300, and M7100 Series Switches Enter alphanumeric characters only. Characters such as # and $ are not supported. The number of characters cannot exceed 31 the switch with all its options, see the M6100 Web User Guide, which is available at downloadcenter.netgear.com. Get Started 15 - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 16
M6100, M5300, and M7100 Series Switches Overview of the Web Management Interface , and you do not need to perform the following task. To configure the management VLAN interface and service port through the web management interface: 1. Prepare your computer with a static IP address in the 169.254 - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 17
M6100, M5300, which is the default IP address of the management VLAN interface. For the service port, the default IP address is 169.254.101.100. The Login Management > IPv4 Management VLAN Configuration. 8. Select the Configuration Method Manual radio button. 9. In the IP Address field, enter the - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 18
M6100, M5300, and M7100 Series Switches 12. Select System > Management > IPv4 Service Port. 13. Select the Service Port Configuration Protocol None radio button. 14. In the IP Address field, enter the service port IP address. For example, enter 172.26.1.110. 15. In the Subnet Mask field, enter the - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 19
configure the switch with all its options, see the M6100 Web User Guide, which is available at downloadcenter.netgear.com. Configure , Mozilla Firefox, or Microsoft Internet Explorer. 3. Enter the management VLAN or service port IP address of the switch in the web browser address field. The Login - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 20
M6100, M5300, and M7100 Series Switches 9. In the Password field, enter a new password and then retype it in the Confirm Password field. Note: If SNMPv3 authentication - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 21
2. Use the Auto Install Configuration 2 Auto Install is a software feature that provides for the configuration of a switch automatically when the switch is initialized and no configuration file is found on the switch. This chapter includes the following sections: • Auto Install Configuration - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 22
M6100, M5300, and M7100 Series Switches Auto Install Configuration Concepts The downloaded configuration file is not distributed across the chassis. When an administrator saves the configuration, - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 23
M6100, M5300, and M7100 Series Switches - The address of the TFTP server (siaddr) to be used for Auto Install requests. You can also enter this information manually. No DHCP configuration is saved in the startup-config file. About Conflicting TFTP Server Configurations The TFTP server IP address can - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 24
M6100, M5300, and M7100 Series Switches Default Network Configuration File If the switch cannot find the specified bootfile or the bootfile name from the DHCP server, - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 25
M6100, M5300, and M7100 Series Switches About Obtaining an Image from a TFTP Server Through Auto Install You can use Auto Install to let the switch download - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 26
M6100, M5300, and M7100 Series Switches The configuration file is located on the TFTP server (for example, switch.cfg). 192.168.0.1 192.168.0.2 DHCP server TFTP - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 27
M6100, M5300, and M7100 Series Switches Configure Auto Install Through the Web Management Interface This section describes how to configure Auto Install through the web management - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 28
M6100, M5300, and M7100 Series Switches Auto Install is complete. The message also indicates that the configuration must be saved to prevent Auto Install from being - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 29
M6100, M5300, and M7100 Series Switches Event Logging for the Auto Install Process The switch logs a message for each of the following events: • The Auto Install - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 30
for a Switch • Load the License File onto the Switch Note: License keys are available only for these switch models: M5300-28G, M5300-52G, M5300-28G-POE+, and M5300-52G - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 31
M6100, M5300, and M7100 Series Switches Register Your Switch Registering your switch gives you access to phone or online support and validates the hardware only for these switch models: M5300-28G, M5300-52G, M5300-28G-POE+, and M5300-52G-POE+. To activate a license key for a switch: 1. Obtain - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 32
M6100, M5300, and M7100 Series Switches 4. Click Activate license key for registered product. You are directed to the Software License Registration website. Because the license key - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 33
M6100, M5300, and M7100 Series Switches Use the Web Management Interface to Load a field. Enter 169.254.100.100, which is the default IP address of the management VLAN interface. For the service port, the default IP address is 169.254.101.100. The Login screen displays. 5. Enter the user name - Netgear M6100-44G3-POE | Software Setup Manual Software Version 11.x - Page 34
M6100, M5300, and M7100 Series Switches The license key is downloaded. Manage Switch Registration and Licenses 33
350 East Plumeria Drive
San Jose, CA 95134
USA
March 2015
208-10798-01
M6100, M5300, and M7100 Series
Switches
Software Setup Manual
Software Version 11.0.0