Netgear MBM621 MBM621 Installation Guide
Netgear MBM621 - 3G HSDPA Ethernet Modem Manual
 |
UPC - 606449056945
View all Netgear MBM621 manuals
Add to My Manuals
Save this manual to your list of manuals |
Netgear MBM621 manual content summary:
- Netgear MBM621 | MBM621 Installation Guide - Page 1
)NSTALLATION - Netgear MBM621 | MBM621 Installation Guide - Page 2
and hold down the reset button for 5 seconds. Technical Support Contact your Internet Service Provider for technical support. Register your product at http://www.NETGEAR.com/register, so that you can check for firmware updates for the modem. This symbol was placed in accordance with the European
-
1 -
2
 |
 |
Mobile Broadband Modem MBM621
Requirements
Before installation, make sure that these requirements are met:
•
You must have an account for wireless broadband service, and you must be located in
an area with wireless broadband coverage. Check with your Internet Service Provider
(ISP) if you are not sure.
•
You need an activated SIM card from your ISP.
•
You must have a computer with an available Ethernet port to connect to the Mobile
Broadband Modem.
•
Your computer must be configured with DHCP.
•
For installation with a router, first install the Mobile Broadband Modem to work with
a computer. Then follow the instructions that came with the router to connect the
router to the modem.
Installation
Follow these instructions to install the modem.
Install the SIM Card, and Connect the Modem to a
Computer
To connect the Mobile Broadband Modem:
1.
Turn off your computer.
2.
Insert your activated SIM card into the
slot on the rear of the modem.
3.
Attach the cover to protect the SIM
card.
Power On the Modem and Computer
Follow these steps:
1.
Plug in the power adapter to your
modem.
2.
Verify the following:
•
The Power light is lit after
you apply power to the modem.
•
The Status light comes on
briefly and then goes off.
•
The Internet light comes on.
For more information about LEDs, see
“Understanding the LEDs” on the other side of this document.
3.
Attach the feet to the modem, and adjust
the antenna so that it is pointed up at a 90
degree angle for best performance.
4.
Turn on your computer, let the operating
system boot up, and log in as needed.
The
Ethernet (LAN) light on the
modem lights up.
4.
Connect the Ethernet cable that came with your
modem to an Ethernet local area network (LAN)
port on your computer. and to the Ethernet port on
the modem.
Log In to the Modem, and Connect to the Internet
1.
On your computer, open a Web
browser.
2.
Type
http://modemlogin.net
in the address field of your browser.
3.
Enter
admin
for the user name, and
password
for the password, both in
lower case letters.
The Broadband Settings screen opens.
•
If your SIM card is programmed by your ISP
with broadband settings, the settings are
displayed on this screen. Click Connect. The
modem connects to the Internet.
•
If your SIM card is not programmed then you
must enter the settings, click
Apply
to save
the settings, and then click Connect. The
settings are explained below:
–
User Name.
The user name for the
broadband Internet service account.
This is not admin, which is the modem user name.
–
Password.
The password for the broadband Internet service account.
–
PIN Code.
The PIN code for the SIM card.
–
APN.
The ISP network name.
–
PDP Type.
The type of packet data protocol.
–
Connection check boxes.
These settings determine whether or not the
modem connects at startup or reconnects when an Internet connection is
lost.
If you are not sure what to enter for these settings, contact your ISP.