Nikon 6479 Instruction Manual

In the event that you should require service for your Nikon

RIFLESCOPE, in case of USA market, please send it directly to:

Nikon Scope Service

841 Apollo Street, Suite 100

EI Segundo, CA. 90245-4721

1-800-Nikon SV.

In other market, please bring it to dealer from which you purchased it.

Pour les autres marchés, veuillez apporter la lunette de visée au

magasin où vous l'avez achetée.

3-9x40

Instruction manual/Mode d'emploi

MUZZLELOADING RIFLESCOPE

F

E

3-25, Futaba 1-chome, Shinagawa-ku, Tokyo 142-0043, Japan

Tel:

+81-3-3788-7697

Fax:

+81-3-3788-7698

Manufacturer:

Printed in the Philippines (545B)1E/1107

Imprimé aux Philippines

Congratulations on your choice of a Nikon INLINE XR Muzzleloading Riflescope. Your new scope is

the finest example of Nikon's rugged and durable construction and precision bright optics; important

qualities for a serious shooter's riflescope.

Whether you use your scope for hunting or for target shooting, the procedure for mounting is

identical. You should acquire a set of high quality steel mounting rings which have a standard

diameter of 25.4 mm (1 inch). Follow the ring manufacturer's instructions for mounting procedures.

After mounting the scope on your muzzleloader, follow the procedures for reticle alignment.

When setting the reticle for hunting, you should determine your standard range and then adjust the

reticle based upon that target distance. For targets which vary from that standard distance you may

simply adjust the position of the reticle in relation to your target, or you may wish to use the

procedure for trajectory compensation. It's up to your personal preference.

We hope that you will enjoy your new Nikon INLINE XR Muzzleloading Riflescope for many years to

come. Enjoy using it, and above all, always follow safe shooting procedures!

The product(s) described herein may be subject to export control regulations in the relevant

country(ies). It (they) should not be exported without authorization of the exporting governmental

authority if the regulations apply.

Caution

(1)

Do not look at the sun through the riflescope. It will permanently damage your eye. This

precaution applies to all optical devices such as cameras and binoculars.

(2)

The riflescope is effectively sealed against moisture and dust. You may use your scope

safely either in the rain or in dusty climates. To preserve the appearance of the scope, we

suggest that it be dried and cleaned prior to storage. Use a soft cloth for cleaning metal

surfaces and use photographic lens tissue to clean the scope's lenses.

1. Nomenclature

Magnified Figure of

Hand turn Grip

Fig. 1-2

Fig. 1-1

2. Specifications

Model

Actual Magnification

3-9x40

3-9x

40

1.57

4.4

0.17

127.0-127.0

5.0-5.0

8.4-2.8

25.2-8.4

25.4

1

49.3

1.94

288

11.3

390

13.8

1 click = 1/4"

60

91.44

100

42

1.65

Objective Diameter

(mm)

(in)

Exit Pupil

(mm)

(in)

Eye Relief

(mm)

(in)

Field of View at 100m/yd

(m)

(ft)

Tube Diameter

(mm)

(in)

Objective Tube Diameter

(mm)

(in)

Length

(mm)

(in)

Weight

(g)

(oz)

Adjustment Graduation

(moa)

Maximum Internal

Adjustment

(Elevation & Windage)

(moa)

Parallax Setting

(at factory)

(m)

(yards)

Structure

★

Waterproof (maximum depth of 2 meter

for up to 5 minutes) and Nitrogen Gas

Outside Diameter of

Eyepiece

(mm)

(in)

3. Instructions

(1) Focusing

●

Look through the eyepiece with your eye positioned about 10 cm (4 in) away from the

eyepiece lens (Fig. 3-1),

and you will see the BDC 300 reticle (Fig. 3-2).

Be sure your eye is positioned within proper alignment and proper eye relief otherwise the

view will "black out".

●

Point the objective end of the scope at the sky (Do not point at the sun) or at a plain

unpatterned wall.

Turn the eyepiece adjustment counter-clockwise and then turn it clockwise until the reticle

appears sharp.

(2) Magnification

The INLINE XR Riflescope has a variable magnification from 3 to 9x.

To change powers, just rotate the power selector ring until the desired magnification appears

adjacent to the power index dot (Fig. 1-1).

(3) Adjustment of the riflescope

Sighting through the riflescope, align the rifle with your aiming point on the target and shoot a

trial round. If the bullet does not hit the aiming point, adjust the elevation and windage after

removing the Adjustment cap, as follows:

For the INLINE XR Riflescope adjustment is made by turning the grip by hand. If the bullet hits

under the aiming point, turn the grip in the direction of the arrow marked "U" (Fig. 3-3). If the

bullet hits to the left of the aiming point, turn the grip in the direction of the arrow marked "R"

(Fig. 3-3).

(4) Zero setting of grip

(Fig. 3-4)

After the reticle has been adjusted to the point of impacts, with the grip held with your fingers to

avoid shifting of the aligned grip, turn the grip screw in top of the grip counterclockwise with

coin. Then lift the grip up and align the "

▼

" with the index mark. It may happen that the "

▼

"

could not align with the index mark exactly because of the coupling pitch of the grip with the

shaft. And by securing the grip with your fingers to avoid shifting of the grip, turn the grip screw

clockwise with the coin until the grip is firmly secured.

Note:

●

The windage and elevation scales of the INLINE XR Riflescope are calibrated in divisions of

1/4 minute of angle with a click at intervals of 1/4 minute of angle.

●

When adjusting the reticle to the point of aim, remember that one minute of angle equals

approximately one inch (2.54 cm) at 100 yards (91.44 m). Therefore, if the impact point is

two inches (5.08 cm) low and one inch (2.54 cm) right at 100 yards (91.44 m), you should

adjust two minutes of angle up one minute of angle left.

Maintenance

(1) Lens cleaning

To remove dirt or fingerprint, soak gauze or lens cleaning paper (silicon-free paper sold at

camera shop) with a small quantity of absolute alcohol (available from drugstore) and lightly

wipe off. Wiping with handkerchief of leather is not recommended as it is likely to damage the

lens surface.

Dust may scratch the lens surface or corrode the lens.

Brush dust off using a soft oil-free brush.

(2) Scope Exterior

Use a soft dry cloth to wipe off any dirt or finger-prints that might accumulate.

It is not necessary to oil the scope's surface.

(3) Windage/Elevation Adjustments

These adjustments are permanently lubricated. Do not attempt to lubricate them. Cover with

caps supplied, except when adjusting, to keep out dust and dirt.

(4) Eyepiece Adjustment

This adjustment is permanently lubricated. Do not attempt to lubricate.

(5) Power Selector Ring

No lubrication is required on the power selector ring.

Do not loosen or remove screws in power selector ring.

Waterproof models:

The Nikon Riflescope is waterproof, and will suffer no damage to the optical system if submerged or

dropped in water to a maximum depth of 2 meters for up to 5 minutes.

The Nikon Riflescope offers the following advantages:

●

Can be used in conditions of high humidity, dust and rain without risk of damage.

●

Nitrogen-filled design makes it resistant to condensation and mold.

Observe the following when using the Nikon Riflescope.

●

As the unit does not have a perfectly sealed structure, it should not be operated nor held in

running water.

●

Any moisture should be wiped off before adjusting movable parts (Elevation / Windage

adjustment knob, eyepiece, etc.) of the Nikon Riflescope to prevent damage and for safety

reasons.

To keep your Nikon Riflescope in excellent condition, Nikon Vision recommends regular

servicing by an authorized dealer.

＊

Specifications and design are subject to change without notice.

＊

No reproduction in any form of this "Instruction manual," in whole or in part (except for brief quotation in critical

articles or reviews), may be made without written authorization from NIKON VISION CO., LTD.

3-9x40

Fig. 3-3

Eyepiece Adjustment

Eye Relief

Fig. 3-1

Objective Lens

Eyepiece Lens

Elevation Adjustment

Windage Adjustment

Eyepiece Adjustment

Power Index Dot

Power Scale

Power Selector Ring

Adjustment Cap

＊

(545B)1E/1107

(at minimum magnification)-(at maximum magnification)

moa=minute of angle (in front of 100 yards one moa is nearly equal to one inch.)

Nikon riflescopes are factory set to be parallax free at 100 yards (91.44 m).

＊

＊＊

＊＊＊

＊＊＊

＊

＊＊

Fig. 3-4

Fig. 3-2

BDC 300 Reticle

Nikon 6479 Instruction Manual

Nikon 6479 - Buckmaster Scope 3-9x40 APG Nikoplex Md Manual

Nikon 6479 manual content summary: