Oki C830dtn Data Protection Kit Installation Instructions
Oki C830dtn Manual
View all Oki C830dtn manuals
Add to My Manuals
Save this manual to your list of manuals |
Oki C830dtn manual content summary:
- Oki C830dtn | Data Protection Kit Installation Instructions - Page 1
Hard Disk Drive (HDD) Data Protection Kit Installation Instructions 59399801 - Oki C830dtn | Data Protection Kit Installation Instructions - Page 2
© 2009 by Oki Data Americas, Inc. All rights reserved. Disclaimer Every effort has been made to the latest product information, printer drivers, manuals, special offers, etc., go to http://my.okidata.com Trademark Information OKI is a registered trademark of Oki Electric Industry Company, Ltd. - Oki C830dtn | Data Protection Kit Installation Instructions - Page 3
this Data Protection Kit is installed in your printer: If the HDD becomes damaged • Both the HDD and the printer control board must be replaced. The printer control board can only be used with the Data Protection Kit HDD installed. Note: For printer control board replacement, contact your Oki Data - Oki C830dtn | Data Protection Kit Installation Instructions - Page 4
Installation 1. Turn off the printer and detach the power cord from the back of the printer. 2. Detach the interface cable. 4 - Oki C830dtn | Data Protection Kit Installation Instructions - Page 5
3. Open the top cover. 5 - Oki C830dtn | Data Protection Kit Installation Instructions - Page 6
Warning! If the printer has been powered on recently, the fuser will be hot. This area is clearly labeled. 4. If it is not already open, lower the MP Tray. 5. Lift the inside cover release and open the cover. 6 - Oki C830dtn | Data Protection Kit Installation Instructions - Page 7
6. Loosen the thumbscrew (1) holding the side panel in place. Lift the left edge of the side cover slightly and pull the cover away from the printer at the top. Lift the cover slightly to remove it from the printer. Place it safely to one side. 7 - Oki C830dtn | Data Protection Kit Installation Instructions - Page 8
7. Slide the access door in the metal plate to the right and open it. 8. Remove the HDD from its shipping package. Caution! Observe antistatic precautions when installing the hard disk drive. 8 - Oki C830dtn | Data Protection Kit Installation Instructions - Page 9
9. Plug the connecting cable (1) firmly into the connector (2) on the printer, then tighten the two thumbscrews (3) to fasten the HDD in place. 9 - Oki C830dtn | Data Protection Kit Installation Instructions - Page 10
10. Swing the access cover closed and slide it to the left to secure it in the metal plate. 10 - Oki C830dtn | Data Protection Kit Installation Instructions - Page 11
at either end of the inside bottom of the side panel with the slots in the side of the printer. then swing the side panel toward the printer. Be sure to feed the silver ribbon (1) on the printer cover into the slot (2) on the side panel before pushing the panel back onto the - Oki C830dtn | Data Protection Kit Installation Instructions - Page 12
12. Secure the side panel in place with the thumbscrew. 13. Close the inside front cover. 12 - Oki C830dtn | Data Protection Kit Installation Instructions - Page 13
14. If you are not using it, close the MP Tray. 15. Close the top cover. 16. Reattach the interface cable. 13 - Oki C830dtn | Data Protection Kit Installation Instructions - Page 14
17. Plug the power cord into the back and turn on the printer. 14 - Oki C830dtn | Data Protection Kit Installation Instructions - Page 15
Configuration report. 5. When the Configuration report is printed, press On Line to exit the menu system. 6. Examine the first page of the report. Near the top of the page, between the two horizontal lines, you will see the current printer configuration. This should now indicate that the hard disk - Oki C830dtn | Data Protection Kit Installation Instructions - Page 16
HDD in the Driver Windows® Postscript Emulation Driver 1. First Windows Vista Click Start → Settings → [Hardware and Sound] Printer. Windows XP, Server 2003 Click Start → Settings → Printers and Faxes. Windows 2000 Click Start → Settings → Printers. 2. Right click the appropriate printer icon. Click - Oki C830dtn | Data Protection Kit Installation Instructions - Page 17
PCL Driver 1. First Windows Vista Click Start → Settings → [Hardware and Sound] Printer. Windows XP, Server 2003 Click Start → Settings → Printers and Faxes. Windows 2000 Click Start → Settings → Printers. 2. Right click the PCL printer icon. Click [Properties]. 3. Click the Device Option(s) tab. 4. - Oki C830dtn | Data Protection Kit Installation Instructions - Page 18
is selected. 3. Select [Options & Supplies]. 4. Select [Driver]. 5. Select the hard disk drive (HDD) and click [OK]. 6. Exit to the desktop. Mac OS 10.4 (Tiger) 1. Open the Mac OS X [Print & Fax Preferences]. 2. Make sure your model is selected. 3. Select [Printer Setup...]. 4. Select the menu and - Oki C830dtn | Data Protection Kit Installation Instructions - Page 19
10.3 (Panther) 1. Open the Mac OS X [Print & Fax Preferences]. 2. Select [Printing...]. 3. Select [Set Up Printers...]. 4. Make sure your model is selected, then select [Show Info...]. 5. Select the menu and choose [Installable Options...] 6. Select the Hard Disk Drive (HDD) and click [ - Oki C830dtn | Data Protection Kit Installation Instructions - Page 20
© 2009 Oki Data Americas, Inc.
Hard Disk Drive (HDD)
Data Protection Kit
Installation Instructions
59399801