Oki OKIPAGE10ex Users' Guide for the OKIPAGE10ex

Oki OKIPAGE10ex Manual

Get Oki OKIPAGE10ex PDF manuals and user guides View all Oki OKIPAGE10ex manuals
Add to My Manuals
Save this manual to your list of manuals

Oki OKIPAGE10ex manual content summary:

  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 1
    , OCR-A/B supported • Emulations - Standard HP® LaserJet 5 (PCL6), IBM® ProprinterIII/Epson® FX (9-pin emulation) • Printer drivers - Windows® NT 4.0, Windows 95, Windows 98, Windows 3.x • Interface SIMM 8MB (Part# 70033201) • 4MB Memory SIMM Chip (Part# 70028801) ° OKIPAGE 10ex User's Guide 1
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 2
    http://www.okidata.com for the latest information on: • Product Guides • Customer Support • Software Drivers • Corporate Information • Documentation Checking the Contents Unpack your printer. The shipping box should contain: 1. OKIPAGE 10ex Printer (with image drum cartridge installed
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 3
    the printer. Removing Operator Panel Protective Film Lift up the corner and peel the protective plastic film from the control panel. ¶ Only the OKIPAGE 10 and 12 Series Type 5 Image Drum will fit in this unit (Part# 40433305) READY MAN FEED ATTENTION DATA LETTER LEGAL A4 OTHER ENV OKIPAGE 10ex
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 4
    . 6. When the cartridge is in place, push the lock lever forward until it stops. 4. Grasp the lock lever and place the left side of the toner cartridge into the toner well, under the tab. tab 7. Lower the printer cover and press firmly to close. ¯4 OKIPAGE 10ex User's Guide
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 5
    size you are using. ¶ Recommended paper weight for the tray is 16 to 28 lb (60 to 105 g/m2).. 4. Place the tray back into the printer until it locks. Using Legal Size Paper To load legal size paper, open out the tray extender and adjust the rear paper guide. OKIPAGE 10ex User's Guide guide 5 °
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 6
    Setting UpYour Printer 1 Paper Exit Options Two odd size paper READY MAN FEED ATTENTION DATA LETTER LEGAL A4 OTHER ENV 1. Pull the front tray extender forward. 2. Lift out the support bar. ¶ Don't change paper paths 2 for information on using recycled print media. ¯6 OKIPAGE 10ex User's Guide
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 7
    about 10 seconds for the printer to initialize, warm up, and display the ON-LINE message, indicating the printer is ready to receive data. 2. Connect the other end of the cable to the proper connector on your computer. Fasten the cable securely to your computer. OKIPAGE 10ex User's Guide 7 °
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 8
    the READY light goes out and printer is OFF-LINE. 2. Press TRAY TYPE/Print Fonts and hold until FONTS appears. 3. Press ENTER. The font page will print. 4. To print the font page for a different emulation, before pressing ENTER, press > until that emulation displays. ¯8 OKIPAGE 10ex User's Guide
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 9
    the OKI electronic registration program. Printer Drivers Printer drivers must be installed so your software application can communicate with your OKIPAGE 10ex printer and support all of its features. The OKIPAGE 10ex CD-ROM includes printer drivers for printing in the following Windows environments
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 10
    Installing the Driver 1. Close all open applications. 2. Insert the OKIPAGE 10ex CD into your CD-ROM drive. Õ 3. Click the Start button on the Windows taskbar, then choose Settings Printers. 4. Double-click the Add Printer icon. 5. The Add Printer Wizard screen appears; follow the instructions on
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 11
    of installing the following:  OKIPAGE 10ex Standard Driver  OKIPAGE 10ex Status Monitor  Electronic Registration Clear the items you do not want to install. Click Next. ¶ To register your printer online, visit the OKIDATA Web Site at http://www.okidata.com. ° OKIPAGE 10ex User's Guide 11
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 12
    Setting UpYour Printer 1 9. Select Program Folder windows appears, with OKIPAGE 10ex listed. Click Next. Installation begins. 10. To complete the installation, click restart Windows. Click Finish. Click the Help button for a description of each feature. Installing the Advanced Driver 1. From
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 13
    . 4. Click the Add/Remove button. Windows 3.x Tore m ove the printer driver and status monitor: 1. From Program Manager double-click the OKIPAGE 10ex icon (or the group where your printer is installed). 2. Double-click uninstallShield. 3. Restart your computer. ° OKIPAGE 10ex User's Guide 13
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 14
    selections in Menu mode ¶ See "Problem Solving" for a description of display messages. Paper Size Indicator The paper size in the tray is indicated by using the dot at the very bottom of the LCD display. Paper size options are shown immediately below the LCD display. ¯14 OKIPAGE 10ex User's Guide
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 15
    Set the displayed selection as default setting. In OFF-LINE mode, enters the Power Save Sub Menu. Returns to previous Menu item. Clears certain receive data errors and returns printer on-line. Advances to next Menu item. Clears all data and executes internal reset. ° OKIPAGE 10ex User's Guide 15
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 16
    of categories and items, and options. Selections display in the LCD window. 1. Press the ON LINE button to enter off-line mode. set in your application software, will override Menu settings. ¶ Most printer menu options can also be set using the soft operator panel on ¯16 OKIPAGE 10ex User's Guide
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 17
    file and sets the printer accordingly. MANUAL OFF* ON Notes: When PRINTER AUTOMATICALLY SWITCHES TO TRAY WITH SAME SIZE PAPER INSTALLED. (ONLY WHEN 2ND TRAY OR FEEDER IS INSTALLED). EDIT SIZE CASSETTE SIZE* LETTER EXECUTIVE LEGAL 14 LEGAL 13 A4 SIZE *Default Setting OKIPAGE 10ex User's Guide
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 18
    Disable. TRAY1 TRAY 2 (Option) LETTER* EXECUTIVE LEGAL 14 LEGAL 13 A4 SIZE A5 SIZE A6 SIZE B5 SIZE *Default Setting ¯18 Notes: Select paper size. MANUAL LETTER* EXECUTIVE LEGAL 14 LEGAL 13 A4 SIZE A5 SIZE A6 SIZE B5 SIZE COM-9 COM-10 MONARCH OKIPAGE 10ex User's Guide
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 19
    TYPE PAPER SIZE CHECK *Default Setting OKIPAGE 10ex User's Guide Items Level 1 Menu Options DL ENV C5 ENV 2 Operating Your Printer Notes: Select paper size installed in Front Feeder (manual feed). If paper size installed does not match setting, printer will display message requesting the size
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 20
    Operating Your Printer 2 Level 1 Menu when a ROM SIMM option is installed. DLLSOFT is indicated only when a soft font is downloaded at permanent setting. (PCL) FONT NO. I000* TO I046 Notes: Select font by ID Appears if selected font is scalable/proportional spaced OKIPAGE 10ex User's Guide
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 21
    FONTS & SYMBOLS *Default Setting OKIPAGE 10ex User's Guide Level 1 Menu 2 Operating Your Printer Items Options 12.00*, 4.00 columns to fit characters on a line. (PCL) BLNKSKIP OFF*, ON Notes: ON= printer will ignore FF code when buffer is empty. (Sometimes software will print an extra blank
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 22
    Operating Your Printer 2 Level 1 Menu Category PAGE LAYOUT 1 Items Notes: Select font and character pitch. (IBM) CONDENSE Notes: Pitch with 12 cpi LN PITCH (IBM, EPSON) BLNKSKIP 6 LPI* 8 LPI OFF* ON Notes: Set OFF, a blank page will not eject. *Default Setting ¯22 OKIPAGE 10ex User's Guide
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 23
    start position from the top of the page. (IBM, EPSON) L.MRGN 0 INCH 0.1 INCH 1 INCH Notes: Moves horizontal print start position to the right. 2 Operating Your Printer *Default Setting OKIPAGE 10ex User's Guide 23 °
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 24
    Operating Your Printer 2 Level 1 Menu Category Items Options THE FOLLOWING CATEGORIES ARE COMMON TO ALL EMULATIONS PAGE LAYOUT 2 ORIENT Notes:Select Setting ¯24 Notes: If set to enable, performs automatic interface switch with RS-232 if this option is installed. OKIPAGE 10ex User's Guide
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 25
    Default Setting OKIPAGE 10ex User's Guide FONT PROT AUTO, OFF*, 100 KB TO 1.1MB Notes: Reserves a section of memory for downloading fonts; improves for downloading fonts. Reduce RSTBUF/RECBUFF to increase free area. AUTOCONT OFF, ON* Notes: ON, software or data error will cause printer to
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 26
    new toner cartridge to resume printing. TNR SAVE DISABLE*, MEDIUM, LIGHT Notes: Use this feature to conserve toner and reduce printing costs when you are printing rough drafts or proof copies. Medium reduces toner by 30%, light reduces toner by 50%. *Default Setting ¯26 OKIPAGE 10ex User's Guide
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 27
    OKIPAGE 10ex User's Guide Items Level 2 Menu Options 2 Operating Your Printer CLR WRNG ON*, JOB Notes: Warning message appears when printer ON SPEED HIGH*, MEDIUM Notes: HIGH=Data transfer speed maximized. MEDIUM=Select if data transmission problems occur, or with earlier computers. BI-DIRCT
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 28
    Operating Your Printer 2 Level 2 Menu Category Items Options DATABITS 8 BITS*, 7 BITS Notes: Appears when RS232C Board is installed. Select serial interface data bit format. , Swedish, Norwegian, Danish, Dutch , Turkish, Portuguese, Polish *Default Setting ¯28 OKIPAGE 10ex User's Guide
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 29
    data for diagnostics. to exit hex dump mode, turn off the printer. Reset the drum counter after replacing the image drum cartridge. Reserves memory area for receive data Reset, Drum Count Reset and X-Y Adjust functions can also be selected in the printer software. OKIPAGE 10ex User's Guide 29 °
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 30
    types of media, you can adjust the following settings in the printer Menus: Level 1 Menu Media Type - Adjust for paper thickness Level 2 Menu Print Mode - Select dots per inch Darkness Control - Adjust print density Toner Saving - Select proof copy quality to conserve toner OKIPAGE 10ex User's Guide
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 31
    the support bar. READY MAN FEED ATTENTION DATA LETTER LEGAL A4 OTHER ENV 4. Pull the manual feed tray down. OKIPAGE 10ex User's Guide 6. Insert the envelope -flap down and to the left- until the printer grips it. 7. Issue the print command in your software. Selecting Envelopes • No windows
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 32
    may cause problems requiring service that will not be covered by OKIDATA warranty or service agreements. The following recycled paper has been tested and approved for use in OKI printers. • , 50% Recycled, 20% PCW • Strathmore, Script Bright White Wove, 50% Recycled ¯32 OKIPAGE 10ex User's Guide
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 33
    2,000 pages. Remember, this is only an average actual results may vary. The first toner cartridge in your new printer has to fill the drum reservoir and saturate the developing roller with toner. It's normal that the first cartridge will produce about 1,000 pages. ° OKIPAGE 10ex User's Guide 33
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 34
    a clean, soft cloth with a small amount of rubbing alcohol on it. 4. Remove the new image drum cartridge from the package. To install the new image drum cartridge, follow the installation instructions in Section 1 (or the instructions included in the replacement kit). ¯34 OKIPAGE 10ex User's Guide
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 35
    ON-LINE to set the printer off-line. 2. Press /Reset simultaneously and hold for 2 seconds. CLEANING, MANUAL LETTER REQUEST displays. 3. Pull down the manual feed tray and insert a the Print Cleaning Page button. Follow the on-screen instructions. OKIPAGE 10ex User's Guide 35 °
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 36
    in which the jam occurred 1. Slide the paper tray out of the printer. TRAY n FEED JAM or PAPER EXIT JAM (top bin) displays when paper exits to the top bin 1. Open the cover. Lift out the image drum. Be careful: the fuser unit at the back of the printer is hot! ¯36 OKIPAGE 10ex User's Guide
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 37
    the printer. 3. Remove the image drum and look to make sure the paper is cleared and no pieces are left. PAPER EXIT JAM (rear tray) displays if paper exits to rear exit tray 1. Lift the top cover. READY MAN FEED ATTENTION DATA LETTER LEGAL A4 OTHER ENV OKIPAGE 10ex User's Guide 4. Replace
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 38
    : RESET TO SAVE Explanation: Data or DLLs in buffer, menu cannot be reset automatically. Action: Press RESET button to save changes and exit menu. MESSAGE: CPYnn Explanation: Displayed when number of copies is two or more, nn indicates copies. Action: No action needed. OKIPAGE 10ex User's Guide
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 39
    FUSER Explanation: Fuser near end of life. Another message can display on the first line. Action: Normal operations continue. When print quality deterio rates, contact service to replace fuser. MESSAGE: COVER Explanation: Cover is open. Action: Close cover. ° OKIPAGE 10ex User's Guide 39
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 40
    : Press RECOVER to release error. Set PAGE BUF to larger value in Menu 2 MESSAGE: DLL BUFF OVERFLOW Explanation: Data in the DLL buffer has overflowed. Action: Press RECOVER to continue. Decrease amount of DLL fonts (Windows TrueType) or install more memory. ¯40 OKIPAGE 10ex User's Guide
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 41
    protocol of host and printer. Contact service. Symptom: Page has gray background. Problem: Solution: Static electricity, generally from dry, cotton fiber papers, causes toner to stick to background. Change papers to an acceptable laser bond or use a humidifier. ° OKIPAGE 10ex User's Guide 41
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 42
    . Problem: Solution: Problem: Solution: Toner is low and does not distribute properly or the drum is worn out. Replace toner cartridge. Check drum and replace the drum, if necessary. Contact service. and humidity. High Humidity. Recommended operating humidity: 20-80% OKIPAGE 10ex User's Guide
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 43
    your software manual to see if this feature is supported. Symptom: Control codes not operating correctly. Problem: Solution: set AUTOEJCT in MENU2. OKIPAGE 10ex User's Guide Symptom: Data is sent to printer, but nothing happens. ON-LINE message appears. Problem: Solution: Wrong interface
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 44
    length to 66 lines per page, ESC C Pn (Pn = number of lines per page). Symptom: Problem: Solution: Strange symbols appear during normal printing. Wrong symbol set. Make sure the symbol set selected corresponds to symbol set resident, in font card, or in soft font. ¯44 OKIPAGE 10ex User's Guide
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 45
    error. Take printer off-line before rebooting computer. Problem: Solution: Gases are given off by forms or adhesives passing through the hot fusing unit. Make sure the forms you use can withstand heating, and provide adequate ventilation. OKIPAGE 10ex User's Guide 4 Problem Solving 45 °
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 46
    If you can't solve your printer problem after reading this manual, contact these sources for service or support. OKIDATA ONLINE Visit the OKIDATA Web Site at http://www.okidata.com for the latest information on: • Software drivers • Product guides • Customer support • Corporate information • Dealers
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 47
    . If the original packaging in not available, contact your dealer or 1-800-OKIDATA for shipping instructions. For out-of-warranty repairs, allow 30 days for round trip shipping and repair. Before shipping your printer, call for a return authorization number (RA). ° OKIPAGE 10ex User's Guide 47
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 48
    Okidata Service Center Locations UNITED STATES OKIDATA Tel: 1-800-OKIDATA (1-800-654-3282) Fax: 1-609-222-5247 CANADA OKIDATA Tel: 1-800-OKIDATA (1-800-654-3282) Fax: 905-238-4427 MEXICO Oki Data de Mexico, S.A. de C.V. Venezuela S.A. Tel: 782.78.11 Fax: (02) 781.9390 ¯48 OKIPAGE 10ex User's Guide
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 49
    printer. However, the procedure for obtaining service may vary outside the continental United States. Contact your Okidata dealer for such warranty service information. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. OKIPAGE 10ex
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 50
    printer for a printhead failure is limited to one year from date of purchase. For the remaining printhead warranty period, replacement will be at an authorized service center or authorized third party service organization. Call 1-800-OKIDATA for authorized service locations. ¯50 OKIPAGE 10ex User
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 51
    Information Center 46 Customer Service Representatives 46 Customer Support Center 46 D DARKNESS CONTROL 26 DATA message 38 Demo pages 8 Display 8 display window 14 Display window;Control panel 14 DLL BUFF OVERFLOW message 40 Drivers, printer 1 OKIPAGE 10ex User's Guide DRUM CNT RESET message 39
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 52
    startrange> 41, 42, 43 Print speed 1 Printer drivers 9 Printer Messages Cleaning/Maintenance 39 Controller Errors 41 Interface Errors 41 Maintenance Menu Mode 39 Manual Paper Feed Request 40 Paper Errors 40 System 1 W WARM UP message 38 Web Site 46 X xxxxx PAPER message 40 OKIPAGE 10ex User's Guide
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 53
    Data Emergency Toner swallowed (ingested) Toner inhaled Procedure Dilute by giving two glasses of water and induce vomiting by administering Syrup of Ipecac (follow manufacturer’s instructions mg/m3 for total dust OKIPAGE 10ex User's Guide Fire and Explosion Hazard Data Flash Point (Method Used):
  • Oki OKIPAGE10ex | Users' Guide for the OKIPAGE10ex - Page 54
    term inhalation exposure may be associated with producing tumors in laboratory animals. Reactivity Data Stability: Stable Polymerization: Will not occur. Hazardous Decomposition Products: Thermal decomposition of his use of the product. Preparation Date: October 25, 1998 OKIPAGE 10ex User's Guide
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
1
OKIPAGE
10ex
User’s Guide
•
Fast print speed - 10ppm with a 28 MHz RISC micro processor
•
Excellent print quality–True 600 dpi and 600 x1200 graphics
•
Large paper capacity–250 sheet paper tray and manual sheet/
envelope feeder plus options for increasing paper capacity up to
850 sheets
•
Memory - 2MB installed, expandable to 35MB
•
Fonts - 35 PCL
®
fonts (Agfa), 10 True Type fonts, USPS Barcode
font, OCR-A/B supported
•
Emulations - Standard HP
®
LaserJet 5 (PCL6), IBM
®
ProprinterIII/Epson
®
FX (9-pin emulation)
•
Printer drivers - Windows
®
NT 4.0, Windows 95, Windows 98,
Windows 3.x
•
Interface - IEEE 1284 bi-directional parallel interface
•
On-screen status monitor and interactive software operator panel
•
Energy Savings - Power is reduced when not printing
•
1 year overnight exchange warranty, 5 year warranty on the LED
printhead (overnight exchange available in the US and Canada)
Consumables
Toner - 2,000 pages @ 5% print density (Type 5 Toner Cartridge Kit,
Part# 52109001)
Drum - 20,000 pages with continuous printing (Type 5 Image Drum
Cartridge Kit, Part# 40433305)
Options
•
500 sheet 2nd Paper Tray/Mechanism (Part# 70028701)
•
100 sheet/50 envelope Multi-purpose Feeder (Part# 70025101)
•
1 MB Memory Expansion Board with 2 expansion (SIMM)
sockets (Part# 70033101)
•
RS-232 Serial Interface Board with 2 expansion (SIMM)
sockets (Part# 00025302)
To install the following options, a Memory Expansion Board or RS-232
Serial Interface Board must be purchased.
•
Flash Memory SIMM 4MB (Part# 70032601)
•
Flash Memory SIMM 8MB (Part# 70033201)
•
4MB Memory SIMM Chip
(Part# 70028801)