Oki PM4410 Setup Guide for the PM4410

Oki PM4410 Manual

Get Oki PM4410 PDF manuals and user guides View all Oki PM4410 manuals
Add to My Manuals
Save this manual to your list of manuals

Oki PM4410 manual content summary:

  • Oki PM4410 | Setup Guide for the PM4410 - Page 1
    Pacemark 4410 English Setup Guide e4410_tp.p65 1 11/30/98, 2:30 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 2
    is complete, accurate, and up-to-date. Okidata assumes no responsibility for the results of errors beyond its control. Okidata also cannot guarantee that changes in software and equipment made by other manufacturers and referred to in this guide will not affect the applicability of the information
  • Oki PM4410 | Setup Guide for the PM4410 - Page 3
    Printer 9 Getting to Know the Pacemark 4410 9 Installation 10 Remove the Shipping Restraints 10 Install the Ribbon Cartridge 12 Install the Paper Guide the Software 35 The Pacemark 4410 CD 35 Printer Drivers 35 On-Line Registration Program 35 User's Guide 36 Pacemark 4410 Setup Guide
  • Oki PM4410 | Setup Guide for the PM4410 - Page 4
    Warranty 59 FCC/IC/CE Statements 63 Material Safety Data Sheet 65 Conventions Used in this Setup Guide Notes Notes are set in regular type and contain injury or damage to the printer. Important! Important information is set in italics. E-2 Untitled-1 Pacemark 4410 Setup Guide 2 11/30/98,
  • Oki PM4410 | Setup Guide for the PM4410 - Page 5
    an older, non-grounded outlet; contact an electrician to have it replaced with a grounded outlet. Do not use an adapter to defeat the grounding. • The printer must be installed near a power outlet which will remain easily accessible. Pacemark 4410 Setup Guide E-3 Untitled-1 3 11/30/98, 1:24 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 6
    becomes damaged or frayed, replace it immediately. • If you're using an extension cord or power strip with the printer, make sure that the total follow the procedures in Section 4 of your on-line Pacemark 4410 User's Guide for having your printer serviced. These are some of the things to look for:
  • Oki PM4410 | Setup Guide for the PM4410 - Page 7
    03 inch (0.79 mm) thick • Rugged, long-life printhead (400 million characters) • Wide, 136-column format • Network capable • Software selectable or auto-switched rear- and front-feed paper paths • Two user-settable menu configurations Pacemark 4410 Setup Guide Untitled-1 5 E-5 11/30/98, 1:24 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 8
    Select a Location • Firm, level surface capable of supporting approximately 95 lbs. (43 kg) • Clearance to open cover • At least four inches (102 mm : 41 to 95°F (5 to 35°C) • Relative humidity: 20 to 80% • Away from direct sunlight E-6 Untitled-1 Pacemark 4410 Setup Guide 6 11/30/98, 1:24 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 9
    5 1 Printer 2 Ribbon Cartridge 3 Paper Guide 4 Power Cord 5 Cable (only included with 4410s which have Print Server pre-installed) If anything is missing or damaged, contact your dealer immediately. The printer interface cable is not supplied. Pacemark 4410 Setup Guide Untitled-1 7 E-7 11
  • Oki PM4410 | Setup Guide for the PM4410 - Page 10
    Brochure This brochure explains the Pacemark 4410 service enhancement programs available in the U.S. and Canada. On-line User's Guide In addition to the printer drivers, the Pacemark 4410 CD contains • Adobe® Acrobat Reader® 3.0 software • User's Guide Acrobat® file: Recommended minimum requirements
  • Oki PM4410 | Setup Guide for the PM4410 - Page 11
    Printer Getting to Know the Pacemark 4410 Front View Rear-Feed Access Cover Tear Bar Cover Printhead Access Cover Control Panel Rear View Front Access Door Tear Bar Cover On/Off Switch Rear-Feed Access Cover Back Access Door Power Cord Port Network/Option Slot Pacemark 4410 Setup Guide
  • Oki PM4410 | Setup Guide for the PM4410 - Page 12
    PUSH" and open the printhead access cover. 3. Remove the printhead shipping restraint and its retaining screw. Be sure to keep this restraint/screw: it is needed to lock the printhead in place should you ever need to move or ship the printer. E-10 Untitled-1 Pacemark 4410 Setup Guide 10 11/30/98
  • Oki PM4410 | Setup Guide for the PM4410 - Page 13
    4. Remove the red rubber shipping restraints (1) at either end. 1 5. Open the tear bar cover, remove the shipping restraint and close the cover. Caution! Avoid the sharp, serrated tear bar. Pacemark 4410 Setup Guide Untitled-1 11 E-11 11/30/98, 1:27 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 14
    of the cartridge (this engages the ribbon take-up knob). 1 3. Pull out the red shipping restraint (1) and turn the blue knob (2) counterclockwise (in the direction of the molded arrows) to take up any excess slack in the ribbon. E-12 Untitled-1 1 12 2 Pacemark 4410 Setup Guide 11/30/98, 1:27 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 15
    the printhead to the ribbon loading area (1). Caution! Make sure the printer is turned off before proceeding. 1 2. Install the ribbon cartridge in the printer: place the ribbon arms (1) over the metal tabs (2) at either end, then press down on the cartridge. 1 2 2 2 1 Pacemark 4410 Setup Guide
  • Oki PM4410 | Setup Guide for the PM4410 - Page 16
    2 4. Turn the blue knob counter clockwise (in the direction of the molded-on arrows) to take up any slack in the ribbon. Caution! Do NOT turn the knob clockwise: this can cause the ribbon to jam. 5. Close the printhead access cover. E-14 e4410_sg.p65 Pacemark 4410 Setup Guide 14 12/1/98, 5:20 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 17
    Install the Paper Guide Hold the paper guide as shown and place it in the slots on the back of the printer. Pacemark 4410 Setup Guide Untitled-1 15 E-15 11/30/98, 1:29 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 18
    the cable to the computer and secure it with the screws. Default settings for the parallel interface (see Section 1 of your on-line Pacemark 4410 User's Guide for information on changing Menu settings): I Prime = Buffer Print Pin 18 = +5V Auto Feed XT = Invalid (Epson FX emulation only) BiDirection
  • Oki PM4410 | Setup Guide for the PM4410 - Page 19
    to the computer and secure it with the screws. Default menu settings for the serial interface (see Section 1 of your on-line Pacemark 4410 User's Guide for information on changing Menu settings): Parity = None # Serial Bits = 8 Bits Protocol = Ready/Busy Diagnostic Test = No Busy Line = SSD- Baud
  • Oki PM4410 | Setup Guide for the PM4410 - Page 20
    OkiLAN 6100e User's Manual included with your printer for additional information. 1. Open the port access cover. 2. Plug one end of the short cable included with the printer into the network board and the other end of the cable into the parallel port. E-18 Untitled-1 Pacemark 4410 Setup Guide 18
  • Oki PM4410 | Setup Guide for the PM4410 - Page 21
    3. Secure the cable at both ends, then close the port access cover. 4. Plug the RJ45 connector into the EtherNet connector on the OkiLAN board, then connect the opposite end of the cable into the network. Pacemark 4410 Setup Guide Untitled-1 19 E-19 11/30/98, 1:31 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 22
    Connect to Power 1. Attach the power cord to the back of the printer. 2. Plug the opposite end into a suitable, grounded outlet. E-20 Untitled-1 Pacemark 4410 Setup Guide 20 11/30/98, 1:31 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 23
    mm), remove the support between the tractors. printer at the front edge of the support (this promotes the unrestricted flow of paper into the printer), then place a stack of continuous forms below the printer. Recommended height of printer support, 29.5 inches (750 mm). Pacemark 4410 Setup Guide
  • Oki PM4410 | Setup Guide for the PM4410 - Page 24
    forms you will be using. The movement of the left tractor is limited to ensure that the paper covers the paper-out sensor. E-22 Untitled-1 Pacemark 4410 Setup Guide 22 11/30/98, 1:32 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 25
    4. Center the supports between the tractors. Left Tractor 1. Open the left tractor pin cover, place the paper holes on the pins, indent from the paper edge at 0 to 1.5 inches in 0.1-inch increments), then push the lock lever back 1 Pacemark 4410 Setup Guide Untitled-1 23 E-23 11/30/98, 1:33 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 26
    of paper is directly aligned (left-right) with its entry point into the tractors: this will promote a smooth flow of paper into the printer. 2. Close the front access door. 3. Press FF/LOAD to load the paper into the print path. E-24 Untitled-1 Pacemark 4410 Setup Guide 24 11/30/98, 1:34 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 27
    on the platen and damaging the printhead. Other paper widths must be set using your software application. To change the menu setting to 8 inches, turn the printer on, then: a. Press MENU. Panel Overview section of this Setup Guide. Pacemark 4410 Setup Guide Untitled-1 25 E-25 11/30/98, 1:34 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 28
    1. Position the printer at the rear edge of the support (this promotes the unrestricted flow of paper into the printer), then place a stack of continuous forms below the printer. Recommended height of printer support, 29.5 inches (750 mm). E-26 Untitled-1 Pacemark 4410 Setup Guide 26 11/30
  • Oki PM4410 | Setup Guide for the PM4410 - Page 29
    roughly fit the width of the continuous forms you will be using. The movement of the right tractor (as viewed from the back of the printer) is limited to ensure that the paper covers the paper-out sensor. Pacemark 4410 Setup Guide Untitled-1 27 E-27 11/30/98, 1:34 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 30
    between the tractors, then position the paper guide (1) over the support (2). 1 2 Right Tractor (viewed from the back of the printer) 1. Open the tractor pin cover, place the paper inch increments), then push the lock lever back. 1 E-28 Untitled-1 Pacemark 4410 Setup Guide 28 11/30/98, 1:35 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 31
    the print path. The printer is set to a default rear-feed paper width of 13.6 inches (136 columns). If you are using 9-inch paper, you must enter the printer menu and change the setting to 8 inches (80 columns) to avoid printing on the platen and Pacemark 4410 Setup Guide Untitled-1 29 E-29 11
  • Oki PM4410 | Setup Guide for the PM4410 - Page 32
    printhead. Other paper widths must be set using your software application. To change the menu setting to 8 inches, turn the printer Guide. Switching Paper Paths The Pacemark 4410 is set at the factory for software control of the paper path. You can enter the menu and change this so that the printer
  • Oki PM4410 | Setup Guide for the PM4410 - Page 33
    Changing Paper Paths Manually To change paper paths manually: 1. Press PARK. The current paper and that the printer is turned off. 2. Press and hold LF (1) while turning the printer on. 1 To stop the test before it is complete, press ON-LINE/RESET. Pacemark 4410 Setup Guide Untitled-1 31
  • Oki PM4410 | Setup Guide for the PM4410 - Page 34
    using is changed from 13.6 inches to 8 inches before starting the Rolling ASCII test. If you don't, the printhead could be damaged. 2. Press and hold PATH/TOF (1) while turning the printer on. 1 To stop the test, press ON-LINE/RESET. E-32 Untitled-1 Pacemark 4410 Setup Guide 32 11/30/98, 1:36 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 35
    • OKI® Microline® Standard Changing Emulations 1. Press MENU to enter the menu mode. The display reads MENU GROUP Printer Control 2. Press ITEM. The display reads Printer Control exit the menu mode and save the new setting. Pacemark 4410 Setup Guide e4410_sg.p65 33 E-33 12/1/98, 5:21 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 36
    E-34 Untitled-1 Pacemark 4410 Setup Guide 34 11/30/98, 1:36 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 37
    Installing the Software The Pacemark 4410 CD Included on the Pacemark 4410 CD: • Pacemark 4410 Printer Drivers • Pacemark 4410 On-Line Registration Program • Pacemark 4410 User's Guide • Adobe® Acrobat® Reader® 3.0 Software Printer Drivers The Pacemark 4410 CD includes printer drivers for printing
  • Oki PM4410 | Setup Guide for the PM4410 - Page 38
    Pacemark 4410 Printer Driver on Windows 95/98 Minimum System Requirements for Windows 95/98: CPU: i486DX, 66 MHz (90 MHz pentium recommended) RAM: 8 MB (16 MB recommended) Empty hard disk space: 2 MB for use by print spooler 2 MB for User's Guide (optional) 10 MB for Adobe Acrobat Reader Software
  • Oki PM4410 | Setup Guide for the PM4410 - Page 39
    type D:\setup\win95\English\drivers\oemsetup.inf For Windows 98, type D:\setup\win98\English\drivers\oemsetup.inf c. Click OK. You will see PM4410 highlighted. 8. Click Next. 9. Continue with the installation following the instructions on your screen. Pacemark 4410 Setup Guide Untitled-1 37 E-37
  • Oki PM4410 | Setup Guide for the PM4410 - Page 40
    1. Click the Start button on the Windows taskbar. 2. Choose Programs → PM4410. 3. From the submenu, click OKI Pacemark 4410 On-Line Registration. 4. Follow the instructions on your screen. To Install the On-Line Pacemark 4410 User's Guide in Windows 95/98 First, make sure Adobe Acrobat Reader 3.0 is
  • Oki PM4410 | Setup Guide for the PM4410 - Page 41
    On-Line Manual. 7. Follow the instructions on your screen. Viewing the On-Line Pacemark User's Guide in Windows 95/98 1. Click the Start button on the Windows taskbar. 2. Choose Programs → PM4410. 3. From the submenu, click OKI Pacemark 4410 On-Line Manual. Pacemark 4410 Setup Guide Untitled-1 39
  • Oki PM4410 | Setup Guide for the PM4410 - Page 42
    ) Empty hard disk space: 2 MB for use by print spooler 2 MB for User's Guide (optional) 10 MB for Adobe Acrobat Reader Software (optional) To Install the Pacemark 4410 Printer Driver in Windows NT 4.0 These instructions assume "D" is the location of your CD-ROM drive. 1. Close any open applications
  • Oki PM4410 | Setup Guide for the PM4410 - Page 43
    Registration Program in Windows NT 4.0 1. Click the Start button on the Windows taskbar. 2. Choose Programs → PM4410. 3. From the submenu, click OKI Pacemark 4410 On-Line Registration. 4. Follow the instructions on your screen. Pacemark 4410 Setup Guide Untitled-1 41 E-41 11/30/98, 1:36 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 44
    . Next, Install the On-Line User's Guide in Windows NT 4.0 These instructions assume "D" is the location of your CD-ROM drive. 1. Close any open applications. 2. Make sure that the printer is connected to the PC and that the printer is turned on. 3. Insert the Pacemark 4410 CD in your CD-ROM drive
  • Oki PM4410 | Setup Guide for the PM4410 - Page 45
    space: 2 MB for use by print spooler 2 MB for User's Guide (optional) 5 MB for Adobe Acrobat Reader Software (optional)- 12 MB recommended To Install the Pacemark 4410 Printer Driver and On-Line Registration Program in Windows 3.1x These instructions assume "D" is the location of your CD-ROM drive
  • Oki PM4410 | Setup Guide for the PM4410 - Page 46
    the On-Line Registration program: 1. Double click the PM4410 group from the Program Manager. 2. Double click the OKI Pacemark 4410 On-Line Registration icon. 3. Follow the instructions on your screen. To Install the On-Line Pacemark 4410 User's Guide in Windows 3.1x First, make sure Adobe Acrobat
  • Oki PM4410 | Setup Guide for the PM4410 - Page 47
    OK. 5. Click On-Line Manual. 6. Follow the on-screen instructions. Viewing the On-Line Pacemark User's Guide in Windows 3.1x 1. Double click the PM4410 group from the Program Manager. 2. Double click the OKI Pacemark 4410 On-Line Manual icon. Pacemark 4410 Setup Guide Untitled-1 45 E-45 11/30
  • Oki PM4410 | Setup Guide for the PM4410 - Page 48
    E-46 Untitled-1 Pacemark 4410 Setup Guide 46 11/30/98, 1:36 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 49
    to receive data. Blinking: Printer is in Print Suppress mode. GROUP/ITEM/OPTION Buttons: For use in Menu Mode only STORE Button: For use in Menu Mode only ON-LINE/RESET Button: Press to switch printer on/off line. With SHIFT, press and hold to reset printer. Pacemark 4410 Setup Guide e4410_sg
  • Oki PM4410 | Setup Guide for the PM4410 - Page 50
    as Top of Form CONFIG Button: With printer off line and no data being sent: Press to switch between preset menu configurations CFG1 and CFG2. For more information on the preset menu configurations, see Section 1 of the OKI Pacemark 4410 On-Line User's Guide. LF/Micro Feed Down Button: Press to
  • Oki PM4410 | Setup Guide for the PM4410 - Page 51
    through available setting values. ITEM Button: Press to page through available items for the selected group. With SHIFT, press to page backwards through available items. Pacemark 4410 Setup Guide E-49 Untitled-1 49 11/30/98, 1:36 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 52
    paper path. You can store up to two TOFs for each path: one under CFG1 and one under CFG2. See Section 1 of the on-line Pacemark 4410 User's Guide for more information. The factory setting for TOF is 0.35 inch (9 mm) down from the top of the page. E-50 Untitled
  • Oki PM4410 | Setup Guide for the PM4410 - Page 53
    Setting the TOF The TOF can be set with the printhead access cover open. To set the TOF in fine increments over TOF to the factory setting, turn the printer off, then press and hold GROUP and OPTION (1) while turning the printer back on. 1 Pacemark 4410 Setup Guide Untitled-1 51 E-51 11/30/98, 1:
  • Oki PM4410 | Setup Guide for the PM4410 - Page 54
    Temporarily Changing the Print Start Position To set the print start position lower for one page only: press LF (1) until you reach the position on the paper where you want the printing to start. 1 E-52 Untitled-1 Pacemark 4410 Setup Guide 52 11/30/98, 1:37 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 55
    on the display changes. 3. Press ON-LINE/RESET. The printer goes back on line with the new CFG showing on the display. For information on how to store Menu settings as CFG1 or CFG2, see Section 1 of your on-line Pacemark 4410 User's Guide. Tear Feature 1 Use this feature to advance continuous forms
  • Oki PM4410 | Setup Guide for the PM4410 - Page 56
    again for printing when the printer receives more data. This feature is normally data is received. This extra paper movement can cause uneven print registration in graphics. If you have this problem, use the menu to turn off the Forms Tear-Off feature. E-54 Untitled-1 Pacemark 4410 Setup Guide
  • Oki PM4410 | Setup Guide for the PM4410 - Page 57
    ) and the ALARM light comes on. To reload the forms, press FF/LOAD. To load the forms from the alternate paper path, press PATH/TOF. Pacemark 4410 Setup Guide Untitled-1 55 E-55 11/30/98, 1:37 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 58
    E-56 Untitled-1 Pacemark 4410 Setup Guide 56 11/30/98, 1:37 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 59
    Specifications For additional specifications, see Appendix A in the on-line Pacemark 4410 User's Guide. Electrical Specifications Voltage: 90 to 264 Volts, AC, universal Frequency: 50 or 60 Hz, +/- 2% Power Consumption Idling: Less than 15 watts Local Test: About 295
  • Oki PM4410 | Setup Guide for the PM4410 - Page 60
    E-58 Untitled-1 Pacemark 4410 Setup Guide 58 11/30/98, 1:37 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 61
    , application conflicts, or consumable items, including but not limited to ribbons, fuses, etc. Okidata will repair (or at its option, replace) at no charge, any defective component(s) of the printer for one (1) year from the data of purchase. This Limited Warranty extends to the original purchaser
  • Oki PM4410 | Setup Guide for the PM4410 - Page 62
    the Pacemark 4410 printer, Okidata dealer from whom the product was purchased, by contacting Okidata directly at 1-800-OKIDATA (U.S. and Canada, English only) or at 1-609-222-5276 (Spanish only), or by contacting one of the service locations listed below. E-60 Untitled-1 Pacemark 4410 Setup Guide
  • Oki PM4410 | Setup Guide for the PM4410 - Page 63
    may vary outside the continental United States. Contact your Okidata dealer for such warranty service information. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Pacemark 4410 Setup Guide Untitled-1 61 E-61 11/30/98, 1:37 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 64
    E-62 Untitled-1 Pacemark 4410 Setup Guide 62 11/30/98, 1:37 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 65
    B. Model Name: Dot Matrix Printer PM4410 Model Number: D21001A This device complies Oki Data Corporation Takasaki Campus 8-1, Futaba-cho, Takasaki-shi, Gunma-ken, Japan (Signed) Isao Suda Dated: October 5, 1998 for Okidata, Div. of Oki Pacemark 4410 Setup Guide Untitled-1 63 E-63 11/30/98, 1:37 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 66
    in accordance with the instructions, may cause harmful interference the equipment off and on, the user is encouraged to try to correct Okidata may void your authority to operate this device. Industry Canada (IC) Radio Interference (RI) Statement This OKI Pacemark 4410 Setup Guide 64 11/30/98, 1:37 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 67
    Material Safety Data Sheet MSDS No. 58064401 for Pacemark 4410 Black Ribbon, P/N 40629302 For more information, contact Okidata at: 2000 Bishops Gate Blvd. Mount Laurel, NJ 08054-4620 For Emergency Information, call 1-800-OKIDATA (US and Canada only). Emergency First Aid Procedures Emergency
  • Oki PM4410 | Setup Guide for the PM4410 - Page 68
    dark, cold place. Do not pull ribbon out of cartridge. Other Precautions: Not applicable The information contained in this MSDS is based on data considered accurate; however, no warranty is the risk of his use of the product. E-66 Untitled-1 Pacemark 4410 Setup Guide 66 11/30/98, 1:37 PM
  • Oki PM4410 | Setup Guide for the PM4410 - Page 69
    printer) Check one: English t MS-10233/1198 Pacemark 4410 User's Guide Français t MS-10234/1198 Pacemark 4410 Guide de L'utilisateur Español t MS-10235/1198 Pacemark 4410 Guía del usuario Português t MS-10236/1198 Pacemark 4410 operator you wish to order an Okidata manual. You will be transferred to
  • Oki PM4410 | Setup Guide for the PM4410 - Page 70
    Untitled-1 68 11/30/98, 1:37 PM
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
Pacemark
4410
Setup Guide
English
e4410_tp.p65
11/30/98, 2:30 PM
1