Oki PRO910 Pro910 User's Guide - Eng

Oki PRO910 Manual

Get Oki PRO910 PDF manuals and user guides View all Oki PRO910 manuals
Add to My Manuals
Save this manual to your list of manuals

Oki PRO910 manual content summary:

  • Oki PRO910 | Pro910 User's Guide - Eng - Page 1
    pro910 Series User's Guide
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 2
    Information Copyright © 2009 by Oki Data. All Rights Reserved Document Information pro910 User's Guide P/N 59320601 Revision 1.0 manuals are available from the web site: http://www.okiprintingsolutions.com Trademark Information Oki and Oki Printing Solutions are registered trademarks of Oki
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 3
    Introduction 12 Features 12 About this guide 14 Software supplied 15 Online usage 16 Printing pages 16 Printer and paper overview 18 Opening and mode 39 Display Panel messages 39 Using the menus 39 Getting started 41 Printer location 41 Turning Off/On 42 Turning Off 42 Turning On 44
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 4
    (Punch unit optional accessory 57 Optional accessories 60 Installing accessories 61 Troubleshooting 62 General 62 Paper Jams 62 Paper jams - printer 62 Open cover, paper jam, tttttt side cover 62 Open accessory 94 Check Finisher, Staple Jam 94 Specifications 100 pro910 User's Guide> 4
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 5
    110 Print Secure Job 111 Menus 112 Tray Configuration 112 System Adjust 117 Menus example 1 - Tray 1 transparencies . . . .121 Menus example 2 - MP Tray paper size . . . . . .122 pro910 User's Guide> 5
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 6
    in a risk of personal injury. SAFETY WARNINGS Please be careful to read and understand the safety warnings on the following pages before operating the printer. Illustrations Illustrations and components are representative only. Your unit may differ slightly from those pictured in this document
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 7
    unit weighs 167.5 lbs (76kg). 3 people are required to lift the printer safely and prevent any risk of personnel injury. The product must be placed on a flat solid surface strong enough to support its weight to prevent any risk of injury. Ensure that there is adequate ventilation all around the
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 8
    this can cause overheating which may lead to fire or electric shock. Ensure the power socket to which the printer is connected is easily accessible at all times. Do not connect or disconnect the power plug with a cable can cause fraying and may lead to fire or electric shock. pro910 User's Guide> 8
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 9
    Guide, this may result in a fire. Ensure loose clothing and hair are kept clear of moving parts when printer is in operation to prevent possible risk of injury. When the printer from the printer, there is a risk of fire. Unplug the mains connector and contact your dealer. If the printer has been
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 10
    Switch printer off before cleaning to prevent any risk of injury. Clean using a damp cloth. Do not use liquid or aerosol cleaners. Do not carry out any operations on the printer that are not specified in the User's Guide. This may result in electric shock, fire and/or injury. pro910 User's Guide> 10
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 11
    is replaced by an incorrect type. Do not touch the battery. Printer battery should not require replacement during the life of the printer. After installing additional memory or a hard disk drive, the cover door into a fire as you may receive burns from a dust explosion. pro910 User's Guide> 11
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 12
    buying an Oki color printer. Your new printer is designed with advanced features to give you clear, vibrant color prints and and smoother gradations of color to lend photographic quality to your documents > Single Pass Color Digital LED technology for high direct PDF printing. pro910 User's Guide> 12
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 13
    spooled and verified printing NOTE This is an optional feature on the pro910 model and is standard on the pro930. > Additional paper trays for Tray1 + 2nd Tray + HCF > Additional memory > Finisher (for stapling printer output) > Punch unit (to extend Finisher functionality) pro910 User's Guide> 13
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 14
    NOTE Images used in this manual may include optional features that your printer does not have installed. This manual is your user's guide (check the web site, my.okidata.com, for the most up-to-date version) for your printer and forms part of the overall user support listed below: > Setup Poster
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 15
    SOFTWARE SUPPLIED CDs: > Drivers and Utilities Contains drivers and application software for use by a general user. > Network and Administrator Utilities Contains software for use by system administrators. > Fiery® Drivers and Tools (pro930 only) pro910 User's Guide> 15
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 16
    ONLINE USAGE This guide is intended to be read on screen using an Adobe Acrobat Reader. Use (or press the Ctrl + P keys). 2. Choose which pages you wish to print: (a) [All pages], (1), for the entire manual. (b) [Current page], (2), for the page at which you are looking. 1 2 3 pro910 User's Guide> 16
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 17
    (c) [Pages from] and [to], (3), for the range of pages you specify by entering their page numbers. 3. Click on [OK]. pro910 User's Guide> 17
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 18
    PRINTER AND PAPER OVERVIEW OPENING AND CLOSING THE TOP COVER CAUTION! To gain access to the inside of the printer, ensure that the top cover is fully opened. To open the top cover, squeeze the top cover handle (1) to release the catch and raise the cover. 1 pro910 User's Guide> 18
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 19
    push harder (2) to close the cover completely. Ensure that the cover is securely closed. 1 2 IDENTIFYING MAJOR COMPONENTS The major components of your printer are identified in the graphics below. 1. Paper holding arm 2. Top cover (face-down stacker) 3. MP Tray (multi-purpose tray) 4. Tray 1 side
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 20
    9. Top cover handle 1 2 3 9 8 7 6 4 5 10. Face-down stacker 11. Power (on/off) switch pro910 User's Guide> 20
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 21
    12. Face-up stacker 10 12 11 13. Interface unit 14. Network interface connector pro910 User's Guide> 21
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 22
    15. Parallel interface connector 16. USB interface connector 17. Power connector 18. Ventilation openings 14 15 18 13 16 17 19. Image drum cartridge and toner cartridge (Cyan) 20. Image drum cartridge and toner cartridge (Magenta) pro910 User's Guide> 22
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 23
    21. Image drum cartridge and toner cartridge (Yellow) 22. Image drum cartridge and toner cartridge (Black) 23. Toner cartridge 24. Image drum cartridge 25. Fuser unit 26. LED heads 26 25 19 20 21 22 23 24 27. Belt unit 28. Drum basket handle pro910 User's Guide> 23
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 24
    29. Drum basket 29 28 27 pro910 User's Guide> 24
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 25
    for all media paths include: > OKI® Bright White, 32 lb US can be used, but the ink must not offset when exposed printer due to the labels peeling off during the printing process. Generally suitable types are: > Avery White Laser Label types 7162, 7664, 7666 (A4), or 5161 (Letter) pro910 User's Guide
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 26
    Stacker - Tray 1 or MP Tray Face-up Stacker 64 - 105 gsm recommended MP Tray Face-up Stacker 0.004 - 0.008 in MP Tray Face-up Stacker pro910 User's Guide> 26
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 27
    in another tray (for example Tray 2 or the MP Tray), you can have the printer automatically switch to that other tray when the current tray runs out of paper. This up and top edge into the printer. Do not use the duplex (two-sided printing) function for transparencies. pro910 User's Guide> 27
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 28
    FACE-DOWN STACKER The face-down stacker on the top of the printer can hold up to 500 sheets of 20 lb (75 g/m²) standard paper, and can handle paper stocks from 17 - Wide, A3 Nobi, Custom size (3.9 - 12.9 in wide, 5.8 -18 in long), using paper stocks in the range 64 - 188 g/m². pro910 User's Guide> 28
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 29
    to the required paper size. 1 3. Fan the paper to be loaded then tap the edges of the stack on a flat surface to make it flush. pro910 User's Guide> 29
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 30
    the paper. To avoid paper jams: • Do not leave space between the paper and the guides and rear stopper. • Do not overfill the paper tray. Capacity depends on the paper type. • Do not load damaged paper. • Do not load paper of different sizes or types at the same time. 3 2 pro910 User's Guide> 30
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 31
    5. Gently push the tray back into the printer. USING THE MP TRAY 1. Squeeze the handle (1) and open the multi-purpose tray. 1 pro910 User's Guide> 31
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 32
    section and swivel out the extension supports (2). 3 2 3. Adjust the paper guides (3) to the size of the paper being used. 4. Fan multi-purpose tray with pre-printed side up and top edge into the printer. • For two-sided (duplex) printing on letterhead, load the paper with pre-printed side down and
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 33
    be installed for this function.) • Envelopes should be loaded face-up with long edge into the printer. Do not select duplex printing on envelopes. • Do not leave space between the paper and the guides. • Do not exceed the paper capacity of approximately 230 sheets, 100 transparencies or 25 envelopes
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 34
    USING THE STACKERS Face-down stacker When the face-up stacker (1) on the left side of the printer is closed (its normal position), paper is ejected to the face-down stacker on the top of the printer. 1 Face-up stacker The face-up exit path is used for heavy paper (cardstock etc.), envelopes
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 35
    2. Flip out the paper support (2). 2 3. Swivel out the paper support extension (3). 3 pro910 User's Guide> 35
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 36
    for more than 2 seconds for a soft shutdown. You can then press this button again for a restart or use the Power switch to turn off the printer completely. pro910 User's Guide> 36
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 37
    9. Online button Switches between online (printer ready to receive data) and offline (printer not ready to receive data) 10. Cancel button Cancels current print job 11. Help button Provides additional textual or image data to supplement what is displayed on the display panel pro910 User's Guide> 37
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 38
    , the printer has encountered a problem and cannot continue printing until the user has intervened and removed the cause of the trouble. The top two lines of the display panel show the printer status. more than 2 seconds while turning on the printer power supply (including pro910 User's Guide> 38
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 39
    a selected consumable). Many of these menu settings can be, and often are, overridden by settings in the Windows printer drivers. However, several of the driver settings can be left at "Printer Setting," which will then default to the settings entered in these printer menus. pro910 User's Guide> 39
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 40
    as follows: 1. Ensure that the display panel indicates that the printer is ready to print. 2. Enter User menu mode by pressing , ensure that an asterisk (*) appears beside the selected parameter Value.) 8. Press the Online button to exit menu mode and return to the ready to print status. Refer to
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 41
    GETTING STARTED This section provides information to help you get started with using your printer. PRINTER LOCATION Check that you have sufficient space for access: > around your printer: 20cm 8in 60cm 24in 60cm 24in 100cm 40in pro910 User's Guide> 41
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 42
    > above your printer: 70cm 28in TURNING OFF/ON TURNING OFF No hard disk drive installed 1. If a hard disk drive is NOT installed, use the On/Off switch. pro910 User's Guide> 42
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 43
    control panel for more than 2 seconds to start the shutdown process. 1 2. When the display panel shows that you can either turn off or restart the printer, use the On/Off switch to turn off the printer. pro910 User's Guide> 43
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 44
    on the printer. CHANGING THE DISPLAY LANGUAGE The default language used by your printer for display messages and for report printing is English. If required, this can be changed using the Panel Language Download Utility located on the installation CD under Optional Utilities. pro910 User's Guide> 44
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 45
    After printing the configuration document, the printer returns to the ready to print status. You can use this document to check your printer configuration. System values and installed accessories are listed at the top of the first page while status values and settings follow. pro910 User's Guide> 45
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 46
    machines. When connecting multiple printers of the same type, they appear as 2), ***** (3), etc. These numbers depend on the order of connecting or turning on each printer. > Ethernet - For network cable connection. NOTE Interface cables are not supplied with your printer. pro910 User's Guide> 46
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 47
    . CONNECTING THE USB INTERFACE Do not connect the USB cable at this time. You will be instructed when to connect the USB cable when you run the Drivers CD. If you are connecting your printer directly to a stand alone computer proceed to the section entitled "Printer Drivers". pro910 User's Guide> 47
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 48
    CONNECTING THE NETWORK INTERFACE CAUTION! Do not connect a USB cable into the network interface connector as this may lead to malfunction. 1. Turn off the printer and the computer. 2. Install the Ferrite core to the Ethernet cable as shown. pro910 User's Guide> 48
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 49
    Software CD into your computer and follow the onscreen instructions. You are prompted to follow a set of basic steps to configure the display panel language, install drivers and other software and finally print a test page to check that your printer is operating correctly. pro910 User's Guide> 49
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 50
    Toner The percentage of Cyan Toner remaining is displayed on the display panel and the printer then returns to the ready to print status. REPLACEMENT INDICATIONS The display panel provides warning messages. Recommended replacement: after approximately 120,000 Letter sheets. pro910 User's Guide> 50
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 51
    these instructions carefully. CAUTION! Only use genuine Oki Original consumables to ensure the best quality and performance from your hardware. Non-Oki Original products may damage your printer's performance or dry, soft cloth for cleaning the LED heads. 1. Open the top cover. pro910 User's Guide> 51
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 52
    2. With an LED lens cleaner or soft cloth, gently wipe each of the four heads (1). Move the cleaner as shown, using a clean section of the cleaner with each pass. Be careful not to damage the guards (2). 1 2 3. Close the top cover. pro910 User's Guide> 52
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 53
    the paper feed rollers if paper jams frequently occur. 1. Remove items like a wrist watch or bracelet and follow the correct steps to turn the printer off depending on whether a hard disk drive is installed. 2. Open Tray 1 side cover and pull out the paper guide plate (1). 1 pro910 User's Guide> 53
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 54
    3. Remove Tray 1 completely from the printer. 4. Gaining access through the gap left by Tray 1, wipe the 3 paper feed rollers (2) with a soft cloth lightly moistened with water. 2 5. Replace Tray 1. pro910 User's Guide> 54
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 55
    6. Return the paper guide plate to its original position and close Tray 1 side cover. 7. Turn on the printer. pro910 User's Guide> 55
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 56
    THE PRINTER CASING 1. Follow the correct steps to turn the printer off depending on whether a hard disk drive is installed. 2. Wipe the printer surface with a soft cloth moistened sparingly with water or neutral detergent. 3. Use a soft dry cloth to dry the printer surface. pro910 User's Guide> 56
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 57
    4. Turn on the printer. EMPTYING THE PUNCH CHIP BOX (PUNCH UNIT OPTIONAL ACCESSORY) When the display panel indicates that the punch chip box is full, empty the box as follows: 1. Operate the Finisher lever and move the Finisher away from the printer. pro910 User's Guide> 57
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 58
    2. Pull out the punch chip box, being careful to keep it level so as not to spill any chips. 3. Discard the chips in an appropriate place. 4. Replace the punch chip box carefully into the Finisher. pro910 User's Guide> 58
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 59
    5. Check that the punch chip box has been replaced correctly then move the Finisher back into position, being careful not to trap your fingers. pro910 User's Guide> 59
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 60
    paper trays) NOTE Tray configurations are: Tray 1 only, Tray 1 + 2nd Tray, Tray 1 + 2nd Tray + 3rd Tray, Tray 1 + HCF, Tray1 + 2nd Tray + HCF. > Finisher (for stapling printer output) > Punch unit (to extend Finisher functionality) pro910 User's Guide> 60
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 61
    its own documentation which gives full instructions on installation. You are advised to follow these instructions carefully. After installation, print in your printer driver(s): > duplex unit > paper tray(s) > Finisher Refer to the Printing Guide for driver setting details. pro910 User's Guide> 61
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 62
    TROUBLESHOOTING GENERAL If the printer display panel does not display anything or is still in stand-by mode 10 minutes after switching on, follow the printer shutdown sequence to switch it off. Check all cable connections before restarting the printer. If the problem trays. pro910 User's Guide> 62
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 63
    1. Squeeze the catch (1) on Tray 1 side cover and open the cover. 2. Holding it by the tab (2), turn the paper guide outward. 2 3. Carefully remove the jammed paper. pro910 User's Guide> 63
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 64
    4. Put the paper guide back into position and close Tray 1 side cover. OPEN COVER, PAPER JAM, SIDE COVER 1. If the MP Tray is open, close it so that the side cover (1) is visible. 1 pro910 User's Guide> 64
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 65
    2. Pull the release lever (2) and pull open the side cover. 2 3. Carefully remove the jammed paper. pro910 User's Guide> 65
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 66
    4. Close the side cover. OPEN COVER, PAPER JAM, TOP COVER 1. Squeeze the top cover handle (1) and open the top cover. 1 WARNING! Be careful not to touch the fuser unit which is hot after printing. pro910 User's Guide> 66
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 67
    fuser unit which may be hot after printing. If the fuser unit is hot, wait until it cools before attempting to remove any jammed paper. pro910 User's Guide> 67
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 68
    Holding the fuser unit (4) by the handle, lift it out of the printer and place it on a flat surface. 4 3 5. Pull up the jam release levers (5) and remove the jammed paper. 5 pro910 User's Guide> 68
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 69
    6. Carefully replace the fuser unit into the printer and turn the lock lever (6) in the direction shown to lock the fuser unit. 6 7. If paper is jammed near the paper exit, open the face-up stacker (7). 7 pro910 User's Guide> 69
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 70
    8. Open the side cover (paper exit) (8) and remove the jammed paper. 8 9. Close the side cover (paper exit) and then the face-up stacker. pro910 User's Guide> 70
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 71
    10. Return the image drum basket (9) into position and check it is locked. 9 11. Close the top cover and ensure it is latched. pro910 User's Guide> 71
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 72
    PAPER JAMS - DUPLEX UNIT (IF INSTALLED) CHECK DUPLEX UNIT, PAPER JAM 1. If a Finisher unit is attached to your printer, operate the lever (1) of the Inverter unit to separate the Inverter from the printer. 1 2. Operate the duplex cover release button (2) and open the cover. 2 pro910 User's Guide> 72
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 73
    3. Carefully remove any jammed paper. 4. Operate the levers (3) and pull out the duplex unit. 3 3 pro910 User's Guide> 73
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 74
    5. Holding the front top cover by the grip (4), push it gently inwards and raise it. 4 6. Remove any jammed paper. pro910 User's Guide> 74
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 75
    7. In similar manner, check for and clear any paper jammed under the rear top cover. 8. Replace the two top covers. pro910 User's Guide> 75
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 76
    9. Raise the front cover of the duplex unit. 10. Push the duplex unit back into position. pro910 User's Guide> 76
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 77
    11. If you detached a Finisher unit to gain access to the duplex unit, replace the Finisher unit. pro910 User's Guide> 77
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 78
    FINISHER (OPTIONAL ACCESSORY) CHECK FINISHER, PAPER JAM/PAPER REMAINS Use the Help button on the printer control panel to check the number displayed. You will need this to be able to clear / 643, 645 (PAPER JAM AROUND FINISHER) 1. Remove any paper at the Finisher paper exit. pro910 User's Guide> 78
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 79
    2. Operate the Finisher lever (1) and move the Finisher away from the Inverter. 1 3. Open the Finisher top cover. pro910 User's Guide> 79
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 80
    4. Carefully remove any jammed paper. 5. Close the Finisher top cover. 6. Move the Finisher back into position and connect it to the Inverter. pro910 User's Guide> 80
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 81
    594, 597, 598/ 644, 646 (PAPER JAM IN FINISHER) 1. Operate the Finisher lever (1) and move the Finisher away from the Inverter. 1 2. Open the Finisher front cover (2). 2 pro910 User's Guide> 81
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 82
    3. Continue to turn the lower knob (3) clockwise until any jammed paper is completely ejected. 3 4. Remove the ejected paper. 5. Close the Finisher front cover. pro910 User's Guide> 82
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 83
    6. Open the Finisher right side cover. 7. Carefully remove any jammed paper. 8. Close the Finisher right side cover. pro910 User's Guide> 83
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 84
    9. Move the Finisher back into position and connect it to the Inverter. 590 (PAPER JAM IN FINISHER/PUNCH UNIT) 1. Operate the Finisher lever (1) and move the Finisher away from the Inverter. 1 pro910 User's Guide> 84
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 85
    2. Move the tab (2) on the right side of the Finisher to align it with the mark (3). 3 2 3. Open the Finisher top cover. pro910 User's Guide> 85
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 86
    4. Carefully remove any jammed paper. 5. Close the Finisher top cover. 6. Move the Finisher back into position and connect it to the Inverter. pro910 User's Guide> 86
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 87
    CHECK INVERTER, PAPER JAM 1. Operate the Finisher lever (1) and move the Finisher away from the Inverter. 1 2. Squeeze the recessed handle (2) and open the left side cover of the Inverter. 2 pro910 User's Guide> 87
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 88
    3. Carefully remove any jammed paper. 4. Close the Inverter left side cover. 5. Move the Finisher back into position and connect it to the Inverter. pro910 User's Guide> 88
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 89
    6. Operate the Inverter lever (3) and separate the Inverter from the printer. 3 7. Open the right side door (4) of the Inverter. 4 pro910 User's Guide> 89
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 90
    8. Remove any jammed paper. 9. Close the right side door. pro910 User's Guide> 90
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 91
    of avoiding them. POSSIBLE CAUSE SUGGESTED REMEDY The printer is not level. Your print media is too be printed are not oriented properly. Place the printer on a steady, level surface. Use appropriate paper stop and paper guides of the tray, or the manual feed guide on the MP Tray to align
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 92
    is dirty. The LED head is dirty. The toner is low. The paper is not suitable for the printer. Wipe the LED head with a LED lens cleaner or with a soft cloth. Replace the toner cartridge. cleaner or with a soft cloth. Replace the toner cartridge. Use recommended paper. pro910 User's Guide> 92
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 93
    properly seated. The toner is low. The paper is moist. The paper is not suitable for the printer. Thickness and type of paper are inappropriate. Recycled paper is being used. Paper is moist or dry fuser unit. Replace the image drum cartridge if the problem is not resolved. pro910 User's Guide> 93
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 94
    - FINISHER (OPTIONAL ACCESSORY) CHECK FINISHER, STAPLE JAM When the display indicates a staple jam has occurred, clear the jam as follows: 1. Open the Finisher front cover. pro910 User's Guide> 94
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 95
    2. Turn the knob in the direction indicated until the colored indicator appears. 3. Remove any paper that awaits stapling in the paper ejection area. pro910 User's Guide> 95
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 96
    4. Pull out the staple unit. 5. Turn the knob in the direction indicated to move the stapler to the front. pro910 User's Guide> 96
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 97
    6. Grip both sides of the staple cartridge, pull it up and remove it. 7. Raise the staple cartridge gate. 8. Remove all staples that are emerging from the staple case. pro910 User's Guide> 97
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 98
    9. Return the staple cartridge gate to its original position. 10. Replace the staple cartridge. 11. Ensure that the staple cartridge is securely installed back into the staple unit then push the staple unit fully home. pro910 User's Guide> 98
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 99
    12. Close the Finisher front cover, being careful not to trap your fingers. pro910 User's Guide> 99
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 100
    ; 36 ppm monochrome (20 - 28 lb paper) 1200 x 600 dpi (pro910) 1200 x 1200 (pro930) PCL 5c, PCL XL 2.1, PS w/PDF Direct (pro910) PCL 5c, PCL XL2.1, Fiery ® PS (pro930) 9 sec (Mono), 10.5 sec (Color) 512 MB (pro910) 1GB (pro930) Trays 1 - 5: 530 sheets Letter each MP Tray: 230 sheets Letter 64-300
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 101
    - 90°F/20 - 80%RH Off: 32 - 110°F/10 - 90%RH Operating: 54dBA maximum Standby: 42dBA maximum Power save: 28dBA maximum after 30 mins background level pro910 User's Guide> 101
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 102
    and has to be changed. The Inverter unit has been separated from the printer and all Finisher functions are disabled. (Finisher/Inverter is an optional accessory.) Invalid data has been received by the printer. Press the ONLINE button to clear this warning. There is a mismatch between the media in
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 103
    . Open tttttt side cover to check for additional paper. You can access help details by pressing the HELP button. Check that the image drum of color cccccc is correctly installed. You can access help details by pressing the HELP button. pro910 User's Guide> 103
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 104
    above are intended for more specialized usage and are not described further here. For full details of using all menus to configure and use the printer, refer to the Network and Configuration Guide. pro910 User's Guide> 104
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 105
    2 pages (tabloid and duplexed = 4 letter sized pages counted). Displays number of color printed pages converted to Letter equivalent. Displays number of monochrome printed pages converted to Letter total pages punched. Displays total pages ejected into the Finisher. pro910 User's Guide> 105
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 106
    . (n.nK) indicates the capacity of the toner cartridge being used. NETWORK ITEM Printer Name Short Printer Name IP Address Subnet Mask Gateway Address MAC Address Network FW Version Web Remote the network firmware version. xx.xx Indicates the network web page version. pro910 User's Guide> 106
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 107
    size of Traym. Displays detected paper size of the MP Tray. DESCRIPTION Displays serial no. of the printer. Displays Asset Number. Asset Number is 8 alphanumeric characters that can be assigned by a user. Same no. of PU (Print Unit) firmware. Same as PU version of Menu Map. pro910 User's Guide> 107
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 108
    page counts as two pages): 1. Ensure that the display panel indicates that the printer is ready to print. 2. Enter menu mode by pressing either the Up-arrow or page count is displayed. 8. Press the Online button to exit menu mode and return to the ready to print status. pro910 User's Guide> 108
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 109
    Statistics Log Execute Usage Report Execute Error Log Execute Color Profile List Execute ITEM Execute DESCRIPTION Prints printer configuration details. Prints summary information about the wired all of Job Log. Prints the error log. Prints a color profile list. pro910 User's Guide> 109
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 110
    Down-arrow buttons repeatedly until Demo 1 is highlighted. 7. Press the Enter button to select this Item and the demo page is printed. 8. After printing, the printer returns to ready to print status. pro910 User's Guide> 110
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 111
    prompted to recheck by Yes/No display, and selecting Yes deletes all jobs. After the job is printed, or the deletion of the job is instructed by the menu, the job is deleted in the manner specified in the printer driver. pro910 User's Guide> 111
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 112
    Tray2-5 implemented. Sets the automatic tray switch function. Specifies selection order priority for automatic tray selection/automatic tray switch. Specifies units for custom paper size. pro910 User's Guide> 112
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 113
    same direction as paper movement. Sets the media type for Traym. User Type1 to User Type5 are reserved for custom paper sizes set in the printer driver. Sets media weight for Traym. The printer detects A3 Nobi, A3 Wide and Tabloid Extra sizes as the same. Use this setting to tell the
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 114
    ITEM Traym Config, where m is in range 1 to 5 (similar arrangement for all trays) VALUE Legal 14 Paper Legal 14 Legal 13.5 DESCRIPTION Sets the length of the legal paper in Traym. Change this to Legal 13.5 if that is the standard legal size in your country. pro910 User's Guide> 114
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 115
    for the direction perpendicular to the direction of paper movement. Sets Custom paper length for MP Tray. Sets for the same direction as paper movement. pro910 User's Guide> 115
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 116
    . Tray selection/ switching uses this tray as the normal tray. If a paper size or type in a tray is not matched to that of the print data, use paper from this tray instead of the specified tray. Makes the MP tray unavailable in auto tray selection/switching
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 117
    recovered when Memory Overflow or Tray Request occurs. If paper is not fed within this time in manual feed, the job is cancelled. Sets the time period between stopping receipt of job data and forced print. For PS, printing is not carried out and the job is cancelled. pro910 User's Guide> 117
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 118
    the printing operation when insufficient toner is detected. Continue: the printer can continue printing while remaining online. Stop: the printer stops printing and goes offline. ON: continues printing the job, parallel to the direction of paper movement (i.e. vertically). pro910 User's Guide> 118
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 119
    of paper movement (i.e. vertically). Used for fine black adjustment for a significantly white horizontal dotted line, a significantly faded image or other such problem that occurs in results printed on plain paper. Decrement setting when a white horizontal dotted line or a snowing image occurs in
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 120
    a significantly faded image or other such a problem that occurs in results printed on transparencies. Decrement setting when a white horizontal dotted line or a snowy image occurs in high- coverage print portions. Increment setting when a faded image occurs. pro910 User's Guide> 120
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 121
    horizontal white lines. This shortens image drum life. Prints out the data received from the host PC in hexadecimal code. MENUS EXAMPLE 1 in Tray1): 1. Ensure that the display panel indicates that the printer is ready to print. 2. Enter menu mode by pressing either . pro910 User's Guide> 121
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 122
    . Check that an asterisk (*) appears beside Transparency. 13. Press the Online button to exit menu mode and return to the ready to print status the MP Tray: 1. Ensure that the display panel indicates that the printer is ready to print. 2. Enter menu mode by pressing either the pro910 User's Guide> 122
  • Oki PRO910 | Pro910 User's Guide - Eng - Page 123
    size is highlighted. 11. Press the Enter button to select this value. 12. Check that an asterisk (*) appears beside the chosen size. 13. Press the Online button to exit menu mode and return to the ready to print status. pro910 User's Guide> 123
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123