Onkyo A-9070 Instruction Manual
Onkyo A-9070 Manual
 |
View all Onkyo A-9070 manuals
Add to My Manuals
Save this manual to your list of manuals |
Onkyo A-9070 manual content summary:
- Onkyo A-9070 | Instruction Manual - Page 1
Integrated Amplifier A-9070 Instruction Manual Thank you for purchasing an Onkyo Integrated Amplifier. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening - Onkyo A-9070 | Instruction Manual - Page 2
instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any - Onkyo A-9070 | Instruction Manual - Page 3
sound pressure from earphones and headphones can cause hearing loss. inside this unit, have it checked by your Onkyo dealer. 8. Handling Notes • If you need equipment. NOTE: This equipment has been tested and found to comply with the limits in accordance with the instructions, may cause harmful - Onkyo A-9070 | Instruction Manual - Page 4
on the power supply cord of this unit should be performed only by qualified service personnel. IMPORTANT The wires in the mains lead are coloured in accordance with the declare in own responsibility, that the ONKYO product described in this instruction manual is in compliance with the corresponding - Onkyo A-9070 | Instruction Manual - Page 5
(WM8742) for L/R Channels • Direct Mode • Tone Control (Bass/Treble) • Balance Control • Independent Headphone Amplifier • Discrete Phono Equalizer • Phono Input (MM/MC) • De-emphasis Function*1 • 3 Digital Inputs (2 sampling rates: 32 kHz, 44.1 kHz, 48 kHz. Other rates are not supported. En 5 - Onkyo A-9070 | Instruction Manual - Page 6
Connecting Onkyo V Components 20 Connecting a Turntable 21 Connecting a Cassette Tape Deck 21 Connecting a Recording Component 22 Using the Integrated Amplifier as a Preamplifier...........23 Separating the Pre-amp and Main Amp Units 24 Using the Integrated Amplifier as a Power Amplifier.....25 - Onkyo A-9070 | Instruction Manual - Page 7
fluorescent lights. Keep this in mind when installing. • If another remote controller of the same type is used in the same room, or the integrated amplifier is installed close to equipment that uses infrared rays, the remote controller may not work reliably. • Don't put anything, such as a book, on - Onkyo A-9070 | Instruction Manual - Page 8
. Position it so that its weight is evenly dispersed on its four legs. Do not install the integrated amplifier in a place with vibration or an unstable location. The integrated amplifier is designed to have high conversion efficiency, however, its temperature will become much higher than other audio - Onkyo A-9070 | Instruction Manual - Page 9
27) Adjusts the volume. F DIRECT switch (➔ page 28) Enables or disables the Direct function. G DIRECT LED (➔ page 28) Lights when the integrated amplifier is in Direct mode. H Information display Displays various information. I INPUT selector (➔ page 28) Selects the input sources in sequence. It is - Onkyo A-9070 | Instruction Manual - Page 10
. N BALANCE L/R buttons (➔ page 29) Adjusts the balance of left and right channels. O SETUP button (➔ page 35) Selects and confirms settings. P PHONES jack (➔ page 31) Connects headphones with a standard plug. En 10 - Onkyo A-9070 | Instruction Manual - Page 11
. K LINE OUT L/R jacks Connect components such as analog line-level sources. The input signals are output with no level adjustment. L PRE OUT L/R jacks Connect a power amplifier when the integrated amplifier is used as a preamplifier (Pre mode). M MAIN IN L/R jacks Connect a preamplifier when the - Onkyo A-9070 | Instruction Manual - Page 12
/BAL button (➔ page 29) Adjusts the tone (bass/treble) and balance of the I integrated amplifier. You can also use the remote controller to control your Onkyo CD Player (e.g. C-7070), Onkyo Dock, or Onkyo J Network Tuner (e.g. T-4070). K Note • Make sure the remote controller is pointed at - Onkyo A-9070 | Instruction Manual - Page 13
Connections Connections Connecting Your Speakers Right Left Speakers A Speakers B Right Left ■ Screw-type speaker terminals Strip 1/2" to 5/8" (12 to 15 mm) of insulation from the ends of the speaker cables, and twist the bare wires tightly, as shown. 1/2" to 5/8" (12 to 15 mm) ■ Banana - Onkyo A-9070 | Instruction Manual - Page 14
cannot be connected. • Two sets of speakers (Speakers A and Speakers B) can be connected to the integrated amplifier. You can select which speakers to output audio to when listening to music. You can also output audio from both sets of speakers. • If you use Speakers A or Speakers B, make sure to - Onkyo A-9070 | Instruction Manual - Page 15
A and SPEAKERS B, it separates high frequency from low frequency signals. Important: • Bi-wiring can be used only with speakers that support bi-wiring. Refer to your speaker manual. • When making the bi-wiring connections, be sure to remove the jumper bars that link the speakers' tweeter (high) and - Onkyo A-9070 | Instruction Manual - Page 16
Remote Interactive), you need to connect your Onkyo CD Player, Network Tuner, or RI Dock to the integrated amplifier with an V cable. Note • problem, plug the integrated amplifier into a different branch circuit. • Do not use a power cord other than the one supplied with the integrated amplifier - Onkyo A-9070 | Instruction Manual - Page 17
CD Player C-7070 Tip • Connect the CD Player to either of the following jacks: LINE IN 1/2/3. Digital Connection (Coaxial or Optical) Integrated Amplifier A-9070 CD Player C-7070 Connect either of them. Tip • Connect the CD Player to either of the following jacks: COAXIAL 1/2, OPTICAL. En 17 - Onkyo A-9070 | Instruction Manual - Page 18
Dock This is an example of connection using the Onkyo Digital Media Transport. Integrated Amplifier A-9070 Connect either of them. COAXIAL OPTICAL ON/STANDBY STANDBY iPod PC UNSSYYNNCC/ Digital Media Transport Note • Use only an Onkyo Dock with digital connections. • To use the V (Remote - Onkyo A-9070 | Instruction Manual - Page 19
T-4070. Note • To use the V (Remote Interactive) connection, you need to change the names of inputs (➔ pages 20, 35). Analog Connection Integrated Amplifier A-9070 Network Tuner T-4070 Tip • Connect your tuner to either of the following jacks: LINE IN 1/2/3. Digital Connection (Coaxial or Optical - Onkyo A-9070 | Instruction Manual - Page 20
Connecting Onkyo V Components Integrated Amplifier A-9070 Network Tuner or CD Player ON/ supported by the integrated amplifier's V. With other components such as MD recorders, the V won't work properly. • Some components may not support all V functions. Refer to the manuals supplied with your Onkyo - Onkyo A-9070 | Instruction Manual - Page 21
Connecting a Turntable Integrated Amplifier A-9070 MM/MC selector L R AUDIO OUTPUT Turntable without a built-in phono preamp Use the MM/MC selector on the back of the integrated amplifier to select either MM or MC, in accordance with the cartridge format of the turntable. Remove the short pins - Onkyo A-9070 | Instruction Manual - Page 22
in the signal output from LINE OUT. • Manual tone adjustments using BASS -/+, TREBLE -/+, BALANCE L/R, and TONE/BAL are not reflected in the signal output from LINE OUT. • See the manual of the recording component for instructions on correct use. Integrated Amplifier A-9070 L R AUDIO IN Cassette - Onkyo A-9070 | Instruction Manual - Page 23
amplifier is used as a pre-main amplifier. This is an example of connection using the power amplifier M-5000R. Important: • In this mode, SPEAKERS cannot be used. • To use this mode, you need to change the "ROUTE" setting (➔ page 39). Integrated Amplifier A-9070 Power Amplifier M-5000R En 23 - Onkyo A-9070 | Instruction Manual - Page 24
equalizer between the pre-amp and main amp units. Important: • Always turn the integrated amplifier off before connecting the MAIN IN jacks. • To use this mode, you need to change the "ROUTE" setting (➔ page 39). Integrated Amplifier A-9070 L R INPUT L R OUTPUT e.g., graphic equalizer Note - Onkyo A-9070 | Instruction Manual - Page 25
the MAIN IN jacks, as a direct connection may cause a massive blast sound and damage the integrated amplifier or your speakers. • This mode can be used with the following limitations: - The volume need to change the "ROUTE" setting (➔ page 39). Preamplifier P-3000R Integrated Amplifier A-9070 En 25 - Onkyo A-9070 | Instruction Manual - Page 26
" flashes on the information display until the speakers or headphones become active. • After a certain time of warming up, the internal temperature of the integrated amplifier stabilizes, and the sound is softened. • The integrated amplifier remembers the state when power was last turned off, and - Onkyo A-9070 | Instruction Manual - Page 27
to 14dB, VOLMAX ■ Operating with the remote controller VOLUME R/X SPEAKERS A B 1 Press SPEAKERS repeatedly on the integrated amplifier. The LED of the selected speakers lights. Note • While headphones are connected, this setting is disabled. • When "ROUTE" is set to "PRE", this setting is disabled - Onkyo A-9070 | Instruction Manual - Page 28
tone control circuit, the Direct function uses the shortest path for enhanced sound quality. Although this function generally turns the display off, the integrated amplifier makes use of a display that doesn't affect the sound quality. It is therefore possible to turn the display on while the Direct - Onkyo A-9070 | Instruction Manual - Page 29
Adjusting the Bass, Treble and Balance You can adjust the bass, treble and left/right output balance respectively. ■ Operating with the remote controller ■ Operating on the integrated amplifier / RETURN TONE/BAL 1 Press TONE/BAL repeatedly. ` BASS: `TRBL (Treble): You can adjust the bass and - Onkyo A-9070 | Instruction Manual - Page 30
Direct function is enabled, "BASS" and "TRBL" are not displayed. • When a signal treated for treble emphasis (pre-emphasis) is detected, the integrated amplifier is designed to restore the original signal characteristics via the "de-emphasis" process. The message "EMPHAS" only appears when a signal - Onkyo A-9070 | Instruction Manual - Page 31
can temporarily mute the output of the integrated amplifier. Using Headphones PHONES jack MUTING 1 Press MUTING. The message "MUTING" flashes on the information display. To unmute the integrated amplifier, press MUTING again. 1 Connect a pair of stereo headphones with a standard plug (1/4 inch - Onkyo A-9070 | Instruction Manual - Page 32
CD Player You can use the integrated amplifier's remote controller to control your Onkyo CD player, pointing the remote controller at the CD player's remote control sensor. Note • With some components, the remote controller may not work, or only - Onkyo A-9070 | Instruction Manual - Page 33
the latest information on the Onkyo Dock components, see the Onkyo web site at: http://www.onkyo.com Before using the Onkyo Dock components, update your iPod with the latest software, available from the Apple web site. For supported iPod models, see the instruction manual of the Onkyo Dock. En 33 - Onkyo A-9070 | Instruction Manual - Page 34
Network Tuner, but the functionality will depend on your Network Tuner's input. To control the Onkyo Network Tuner, an V connection is required (➔ page 20). To control the Onkyo Network Tuner with the integrated amplifier's remote controller, you need to change the input name to "TUNER" (➔ page 35 - Onkyo A-9070 | Instruction Manual - Page 35
selected name flashes rapidly for a few times as the setting is confirmed. 6 Press RETURN repeatedly to exit the setup. ■ Operating on the integrated amplifier SETUP INPUT selector Note • When "ROUTE" is set to "MAIN", the "NAME", "SHOW", "HPLVL" and "ASb" settings are not available. • When the - Onkyo A-9070 | Instruction Manual - Page 36
The current input doesn't appear as selectable. For example, if the input is currently set to "LINE1", "L1" won't appear as selectable. • The integrated amplifier will end the setup if there is no operation for 8 seconds. 5 Press / to switch between ON and OFF. ` ON: Shows the display of selected - Onkyo A-9070 | Instruction Manual - Page 37
Level You can set the volume when using headphones. ■ Operating with the remote controller ■ Operating on the integrated amplifier SETUP INPUT selector /// ENTER RETURN SETUP 1 Press SETUP. 2 Press / repeatedly to select "HPLVL". 3 Press ENTER. The current level is displayed. 4 Press - Onkyo A-9070 | Instruction Manual - Page 38
operation for 8 seconds. Once the Auto Standby (ASb) function has been activated, the integrated amplifier will not automatically turn on even if it receives a signal. To turn on the integrated amplifier, press ON/STANDBY on the integrated amplifier or on the remote controller manually. En 38 - Onkyo A-9070 | Instruction Manual - Page 39
integrated amplifier as a preamplifier (➔ page 23). ` SPLIT: With this setting, you can use the integrated amplifier's pre-amp and power amp mode, the audio coming from MAIN IN is output by speakers with a 32.5 dB amplification. • The integrated amplifier will end the setup if there is no operation - Onkyo A-9070 | Instruction Manual - Page 40
default settings. ` RST-NO: Cancels the operation. 5 Press ENTER. If "RST-YES" is selected, "CLEAR" appears on the information display. The integrated amplifier then automatically turns off. If "RST-NO" is selected, the setup returns to "RESET". 1 Press SETUP repeatedly to select "RESET". 2 Use the - Onkyo A-9070 | Instruction Manual - Page 41
cellular phone that's being used to make a call, the integrated amplifier may output noise. Headphone output is intermittent or there's no sound. • This may be due to dirty contacts. Clean the headphones plug. See your headphones' instruction manual for cleaning information. Also, make sure that the - Onkyo A-9070 | Instruction Manual - Page 42
on: 1. Source component 2. Integrated amplifier (A-9070) When turning the power off: 1. Integrated amplifier (A-9070) 2. Source component Remote Controller or sunlight). • The integrated amplifier is located behind the glass doors of an audio rack or cabinet. Onkyo is not responsible for damages - Onkyo A-9070 | Instruction Manual - Page 43
44.1 kHz/48 kHz/88.2 kHz/96 kHz/ 176.4 kHz/192 kHz compatible (COAX) Analog Stereo Inputs LINE 1, LINE 2, LINE 3, PHONO (MM/MC), MAIN IN ■ Audio Outputs Analog Outputs Speaker Outputs Phones LINE OUT, PRE OUT 4 1 (6.3 ø) ■ Others RI 2 Specifications and features are subject to change without - Onkyo A-9070 | Instruction Manual - Page 44
Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong. Tel: 852-2429-3118 Fax: 852-2428-9039 http://www.ch.onkyo.com/ 1301, 555 Tower, No.555 West NanJin Road, Jin an, Shanghai, China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396 SN 29400849 (C) Copyright
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
 |
 |
Integrated Amplifier
A-9070
Instruction Manual
Thank you for purchasing an Onkyo Integrated
Amplifier. Please read this manual thoroughly before
making connections and plugging in the unit.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new Integrated Amplifier.
Please retain this manual for future reference.
Contents
Introduction
...................................
2
Connections
.................................
13
Turning On & Basic Operations
......
26
Advanced Operations
.................
35
Others
...........................................
41
E
n