Onkyo DTR-40.2 Instruction Manual

Onkyo DTR-40.2 Manual

Get Onkyo DTR-40.2 PDF manuals and user guides View all Onkyo DTR-40.2 manuals
Add to My Manuals
Save this manual to your list of manuals

Onkyo DTR-40.2 manual content summary:

  • Onkyo DTR-40.2 | Instruction Manual - Page 1
    AV Receiver DTR-40.2 Instruction Manual
  • Onkyo DTR-40.2 | Instruction Manual - Page 2
    the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near
  • Onkyo DTR-40.2 | Instruction Manual - Page 3
    fuse inside the unit is not user-serviceable. If you cannot turn on the unit Hearing Loss Caution Excessive sound pressure from earphones and headphones accordance with the instructions, may cause relocate the receiving antenna. • Increase the separation between the equipment and receiver. •
  • Onkyo DTR-40.2 | Instruction Manual - Page 4
    purchasing an Integra AV receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV receiver. Please retain this manual for future
  • Onkyo DTR-40.2 | Instruction Manual - Page 5
    Components 89 Learning Commands 91 Using Normal Macros 92 Others Troubleshooting 93 Specifications 98 About HDMI 100 Using an RIHD-compatible TV, Player, or Recorder ... 101 Video Resolution Chart 103 To reset the AV receiver to its factory defaults, turn it on and, while holding down VCR/DVR
  • Onkyo DTR-40.2 | Instruction Manual - Page 6
    Features and Dynamic Range • Crossover Adjustment (40/45/50/55/60/70/80/90 Mediafly/Napster) * Services available may vary Devices and iPod*9 • Bi-Amping Capability for FL/FR with "Pro Logic", "Surround EX" and the receive HD Radio broadcasts, you must install an Onkyo UP-HT1 HD Radio tuner
  • Onkyo DTR-40.2 | Instruction Manual - Page 7
    are trademarks of Sirius XM Radio Inc. and its subsidiaries. All rights reserved. Service not available in Alaska and Hawaii. *9 iPhone, iPod, iPod classic, iPod nano both digital and analog domains. THX Select2 Plus receivers also feature proprietary THX technologies (e.g., THX Mode) which
  • Onkyo DTR-40.2 | Instruction Manual - Page 8
    Front & Rear Panels Front Panel North American models B C DE F GH I J K L M NO P Q R STU V Australian models W " XYZ [ The actual front panel has various logos printed on it. They are not shown here for clarity. The page numbers in parentheses show where you can find the main explanation for
  • Onkyo DTR-40.2 | Instruction Manual - Page 9
    (Australian models) (➔ 38) AUTO indicator (➔ 31) TUNED indicator (➔ 31) FM STEREO indicator (➔ 31) G SLEEP indicator (➔ 26) K L M NO H Bi AMP indicator (➔ 15) I Headphone indicator (➔ 27) J Audyssey indicator (➔ 28, 52) Dynamic EQ indicator (➔ 55) Dynamic Vol indicator (➔ 56) K Message area L USB
  • Onkyo DTR-40.2 | Instruction Manual - Page 10
    (FRONT L/R, CENTER, SURR L/R, SURR BACK L/R and SUBWOOFER) T PRE OUT jacks (FRONT L/R, CENTER, SURR L/R SB/FH/FW L/R, SUBWOOFER and ZONE 2 L/R) * SB···Surround Back, FH···Front High, FW···Front Wide U Speaker Terminals (FRONT L/R, CENTER, SURR L/R, SURR BACK L/R, FRONT HIGH L/R and FRONT WIDE/ZONE
  • Onkyo DTR-40.2 | Instruction Manual - Page 11
    Remote Controller Controlling the AV Receiver B C D E *1 F G B H I J C To control the AV receiver, press Receiver to select Receiver mode. You can also use the remote controller to control K Onkyo Blu-ray Disc/DVD player, CD player and other components. See "Entering Remote Control Codes"
  • Onkyo DTR-40.2 | Instruction Manual - Page 12
    Home Theater Thanks to the AV receiver's superb capabilities, you can enjoy surround sound with a real sense of movement you can enjoy Dolby Pro Logic IIx, DTS Neo:6, or Onkyo's original DSP listening modes. You can also enjoy THX Surround EX (THX-certified THX speaker system recommended). BC JK
  • Onkyo DTR-40.2 | Instruction Manual - Page 13
    surround sound system, you need to set the speaker settings. You can do this automatically (➔ 28) or manually (➔ 50). Attaching the Speaker Cable Labels The AV receiver the wall outlet before making any connections. • Read the instructions supplied with your speakers. • Pay close attention to
  • Onkyo DTR-40.2 | Instruction Manual - Page 14
    of the speaker terminal. The following illustration shows which speaker should be connected to each pair of terminals. If you're using only one surround back speaker, connect it to the SURR BACK L terminals. Front high right speaker Front wide right speaker Front right speaker Front left speaker
  • Onkyo DTR-40.2 | Instruction Manual - Page 15
    can be used with front speakers and surround back speakers respectively, or bi-amped to provide separate tweeter and woofer feeds for a pair of front speakers that support bi-amping, providing improved bass and treble performance. • When bi-amping is used, the AV receiver is able to drive up to
  • Onkyo DTR-40.2 | Instruction Manual - Page 16
    amplifier. If you have a powered subwoofer, connect it to this AV receiver's SUBWOOFER PRE OUT jack. You can connect the powered subwoofer with two for the channel that you don't want to output (➔ 51). SB···Surround Back, FH···Front High, FW···Front Wide Powered subwoofer See "Connecting the
  • Onkyo DTR-40.2 | Instruction Manual - Page 17
    receiver TV, projector, etc. Blu-ray Disc/ DVD player Game console TV, projector, etc. Blu-ray Disc/ DVD player Game console • Before making any AV connections, read the manuals allow you to enjoy digital sound such as PCM*, Dolby AV receiver does not support SCART plugs. • The AV receiver's
  • Onkyo DTR-40.2 | Instruction Manual - Page 18
    , your TV must support ARC function and "HDMI Control (RIHD)" is set to "On" (➔ 61). Tip • To listen to audio received by the HDMI IN hear from your TV's speakers, by controlling the AV receiver's volume, the sound will be output from the AV receiver's speakers, too. When the "TV Control" setting
  • Onkyo DTR-40.2 | Instruction Manual - Page 19
    Connecting Your Components Front Rear $ & % # " ' ( Connect your components to the appropriate jacks. The default input assignments are shown below. ✔: Assignment can be changed (➔ 49). No. Jack Signal Components Assignable " AUX Input Video Composite video Camcorder, etc Audio L/R
  • Onkyo DTR-40.2 | Instruction Manual - Page 20
    one to the AV receiver. The other jack is for connecting additional V-capable components. • Connect only Integra/Onkyo components to V jacks. Connecting other manufacturer's components may cause a malfunction. • Some components may not support all V functions. Refer to the manuals supplied with your
  • Onkyo DTR-40.2 | Instruction Manual - Page 21
    surge that might interfere with other electrical equipment on the same circuit. If this is a problem, plug the AV receiver into a different branch circuit. • Do not use a power cord other than the one supplied with the AV receiver. The supplied power cord is designed exclusively for use with the AV
  • Onkyo DTR-40.2 | Instruction Manual - Page 22
    Which Connections Should I Use? The AV receiver supports several connection formats for compatibility with a wide range of AV equipment. The format you choose will depend on the formats supported by your components. Use the following sections as a guide. The on-screen setup menus appear only on a
  • Onkyo DTR-40.2 | Instruction Manual - Page 23
    coaxial, or HDMI. When choosing a connection format, bear in mind that the AV receiver does not convert digital input signals for analog line outputs and vice versa. For example, select the TV/CD input selector and your TV must support ARC function. *3 Only the front L/R channels are output. En 23
  • Onkyo DTR-40.2 | Instruction Manual - Page 24
    Front panel Remote controller Turning On Press On/Standby on the front panel. or Press Receiver followed by On on the remote controller. The AV receiver comes on, the display lights, and the Standby indicator goes off. Pressing the remote controller's On again will turn on any components connected
  • Onkyo DTR-40.2 | Instruction Manual - Page 25
    your TV is connected to the MONITOR OUT V, MONITOR OUT S or the COMPONENT VIDEO MONITOR OUT, use the AV receiver's display when changing settings. This manual describes the procedure using the remote controller unless otherwise specified. Selecting the Language Used for the Onscreen Setup Menus You
  • Onkyo DTR-40.2 | Instruction Manual - Page 26
    remaining until the AV receiver sleeps, press Sleep. sound from surround back speakers is output by priority. Note • If the "Speakers Type(Front)" setting is set to "Bi-Amp" (➔ 50), or Powered Zone 2 is being used (➔ 77), this setting cannot be selected. • When the listening mode that doesn't support
  • Onkyo DTR-40.2 | Instruction Manual - Page 27
    input source and listening mode, not all channels shown here output the sound. *4 When you have entered a custom name in "Name Edit" receiver is turned on. 2. The Onkyo DVD player connected to the AV receiver is turned on. 3. The AV receiver is turned on. 4. The input selector of the AV receiver
  • Onkyo DTR-40.2 | Instruction Manual - Page 28
    (default): 1. The Onkyo CD player connected to the AV receiver is turned on. 2. The AV receiver is turned on. 3. The input selector of the AV receiver is set to "TV acoustical problems over the listening area in both the frequency and time domain. The result is clear, well-balanced sound for
  • Onkyo DTR-40.2 | Instruction Manual - Page 29
    AV receiver and the connected TV. On the TV, select the input to which the AV receiver is • If your front speakers are bi-amped, you must select "Bi-Amp" in the "Speakers Type(Front)" MultEQ: Auto Setup - - Review Speaker Configuration - - Subwoofer Front Center Surround Front Wide Front High Surr
  • Onkyo DTR-40.2 | Instruction Manual - Page 30
    Room Correction and Speaker Setup. • If the AV receiver is muted, it will be unmuted automatically when sound distorts, detection issues may occur, so use an appropriate volume level. If the subwoofer has a low-pass filter switch, set it to Off or Direct. Refer to your subwoofer's instruction manual
  • Onkyo DTR-40.2 | Instruction Manual - Page 31
    and hold Tuning R/X. The frequency stops changing when you release the button. Press the buttons repeatedly to change the frequency one step at a time. In manual tuning mode, FM stations will be in mono. Tuning into weak FM stereo stations If the signal from a stereo FM station is weak, it may
  • Onkyo DTR-40.2 | Instruction Manual - Page 32
    comedy, family programming, local traffic and weather and news from your most trusted sources. Once you've purchased a SIRIUS tuner you'll need to activate it and subscribe to begin enjoying the service. Easy to follow installation and setup instructions are provided with the SIRIUS tuner. There are
  • Onkyo DTR-40.2 | Instruction Manual - Page 33
    to "SIRIUS". 1 Press Receiver followed by Setup. The main menu appears onscreen. 2 Use R/X to select "Hardware Setup", and then press Enter. The "Hardware Setup" menu appears. 7. Hardware Setup 1. Remote ID 2. Multi Zone 3. Tuner 4. HDMI 5. Auto Power Down 6. Network 7. Firmware Update 3 Use R/X to
  • Onkyo DTR-40.2 | Instruction Manual - Page 34
    1 Press Enter repeatedly to select Channel Search mode. 5 When you've finished, press Setup. Setup closes. Tip • Alternatively, you can use the AV receiver's Setup, arrow but- tons, and Enter. Selecting SIRIUS Satellite Radio 2 Use R/X to select a channel. You can also use F/S to select a category
  • Onkyo DTR-40.2 | Instruction Manual - Page 35
    Power Down 6. Network 7. Firmware Update Presetting Channels You can store a combination of up to 40 of your favorite SIRIUS Satellite Radio channels and FM/AM radio stations as presets. 1 Tune into the SIRIUS channel that you want to store as a preset. 2 Press Memory on the AV receiver. The preset
  • Onkyo DTR-40.2 | Instruction Manual - Page 36
    PIN Number 1 Press Receiver followed by Setup. The main menu appears onscreen. 2 Use R/X to select "Hardware Setup", and then press Enter. The "Hardware Setup" menu appears. 7. Hardware Setup 1. Remote ID 2. Multi Zone 3. Tuner 4. HDMI 5. Auto Power Down 6. Network 7. Firmware Update 3 Use R/X to
  • Onkyo DTR-40.2 | Instruction Manual - Page 37
    . 1 Press Receiver followed by Tuner, and Setup. The main menu appears onscreen. 2 Use R/X to select "Hardware Setup", and then press Enter. The "Hardware Setup" menu appears. 7. Hardware Setup 1. Remote ID 2. Multi Zone 3. Tuner 4. HDMI 5. Auto Power Down 6. Network 7. Firmware Update Note • If
  • Onkyo DTR-40.2 | Instruction Manual - Page 38
    . In addition to displaying text information, RDS can also help you find radio stations by type (e.g., news, sport, rock, etc.). The AV receiver supports four types of RDS information: ■ PS (Program Service) When tuned to an RDS station that's broadcasting PS information, the station's name will be
  • Onkyo DTR-40.2 | Instruction Manual - Page 39
    ■ RDS program types (PTY) Type None News reports Current affairs Information Sport Education Drama Culture music Country music National music Oldies music Folk music Documentary Alarm test Alarm Display None News Affairs Info Sport Educate Drama Culture Science Varied Pop M Rock M Easy M Light
  • Onkyo DTR-40.2 | Instruction Manual - Page 40
    the manuals supplied with your TV and VCR for details. • Video signals connected to composite video inputs can be recorded only via composite video outputs. If your TV/VCR is connected to a composite video input, the recording VCR must be connected to a composite video output. • The surround sound
  • Onkyo DTR-40.2 | Instruction Manual - Page 41
    be selected if your Blu-ray Disc/DVD player is connected to the AV receiver with a digital audio connection (coaxial, optical, or HDMI). • The listening used while you are listening to sound through your TV speakers coming from components connected to the AV receiver ("TV Sp On" appears on the front
  • Onkyo DTR-40.2 | Instruction Manual - Page 42
    Modes The AV receiver's listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound. Explanatory Notes SP Layout JK LM BC D G Listening Mode EF HI ■ Input Source The following audio formats are supported by the
  • Onkyo DTR-40.2 | Instruction Manual - Page 43
    Pro Logic IIx expands any 2-channel source for 7.1-channel play- 4 Dolby Pro Logic II back. It provides a very natural and seamless surround-sound experience that fully envelops the listener. As well as music and movies, video games can P L b M o v i e P P P P also benefit from the dramatic spatial
  • Onkyo DTR-40.2 | Instruction Manual - Page 44
    to 7.1-channel playback. It uses seven full-bandwidth channels of matrix decoding for matrix-encoded material, providing a very natural and seamless surround sound experience that fully envelops the listener. • Neo:6 Cinema Use this mode with any stereo movie (e.g., TV, DVD, VHS). • Neo:6 Music Use
  • Onkyo DTR-40.2 | Instruction Manual - Page 45
    mode expands 5.1-channel sources for 7.1- channel playback. It does ' this by analyzing the composition of the surround source, optimizing the ambient and directional sounds to produce the surround back channel out- put. • THX Select2 Music This mode is designed for use with music. It expands
  • Onkyo DTR-40.2 | Instruction Manual - Page 46
    Onkyo-Original DSP this mode creates a ) lively sound field with a powerful acoustic Surround back and front wide speakers are not supported. *4 Front high and front wide speakers are not supported. *5 For the Blu-ray Discs, Dolby Digital is used in a 3.1/5.1-channel speaker system. *6 AV receiver
  • Onkyo DTR-40.2 | Instruction Manual - Page 47
    COMPONENT VIDEO MONITOR OUT, use the AV receiver's display when changing settings. This manual describes the procedure using the remote controller 2. Multi Zone 3. Tuner 4. HDMI 5. Auto Power Down 6. Network 7. Firmware Update I Remote Controller Setup (➔ 87) 3. Audio Adjust 1. Multiplex/Mono 2.
  • Onkyo DTR-40.2 | Instruction Manual - Page 48
    at the same resolution and with no conversion.  Auto: Select this to have the AV receiver automatically convert video at resolutions not supported by your TV. 480p (480p/576p): Select this for 480p or 576p output and video conversion as necessary.  720p: Select this for 720p output and
  • Onkyo DTR-40.2 | Instruction Manual - Page 49
    on video signal flow and upconversion (➔ 22). • If no video component is connected to HDMI output (even if the HDMI input is assigned), the AV receiver selects the video source based on the setting of "Component Video Input". • When an HDMI IN is assigned to an input selector as explained here
  • Onkyo DTR-40.2 | Instruction Manual - Page 50
    Audyssey MultEQ Room Correction and Speaker Setup function, or set them manually, which is useful if you change one of the connected speakers (➔ 50). For hookup information, see "Bi-amping the Front Speakers" (➔ 15). Note • When bi-amping is used, the AV receiver is able to drive up to 5.1 speakers
  • Onkyo DTR-40.2 | Instruction Manual - Page 51
    . Sounds below the crossover frequency will be output by the subwoofer instead of the speaker. Refer to your speaker's manuals to If the "Surround" setting is set to anything other than "Full Band", "Full Band" cannot be selected here. *4 If the "Speakers Type(Front)" setting is set to "Bi-Amp" (➔
  • Onkyo DTR-40.2 | Instruction Manual - Page 52
    51). • The speakers cannot be calibrated while the AV receiver is muted. • The test tone is output at the Tip • If you're using a handheld sound level meter, adjust the level of each speaker Equalizer  Manual: You can adjust the equalizer for each speaker manually. If you selected "Manual", continue
  • Onkyo DTR-40.2 | Instruction Manual - Page 53
    THX Loudness Plus THX Loudness Plus is a new volume control technology featured in THX Ultra2 Plus™ and THX Select2 Plus™ Certified receivers. With THX Loudness Plus, home theater audiences can now experience the rich details in a surround mix at any volume level. A consequence of turning the volume
  • Onkyo DTR-40.2 | Instruction Manual - Page 54
    forward. If the stereo image feels too wide, or there's too much surround sound, move the sound field forward to improve the balance. Conversely, if the stereo image feels like it's in mono, or there's not enough surround sound, move it backward. Center Width 0 to 3 to 7 With this setting, you can
  • Onkyo DTR-40.2 | Instruction Manual - Page 55
    Manual". DTS ■ Neo:6 Music Center Image  0 to 2 to 5 The DTS Neo:6 Music listening mode creates 6-channel surround sound Select if the listening angle is 40 degrees.  Narrow: Select if the sound even when listening at low volume levels. Audyssey Dynamic EQ solves the problem of deteriorating sound
  • Onkyo DTR-40.2 | Instruction Manual - Page 56
    film mix level. It makes adjustments to maintain the reference response and surround envelopment when the volume is turned down from 0 dB. However, film Audyssey Dynamic EQ Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into account
  • Onkyo DTR-40.2 | Instruction Manual - Page 57
    using your DVD player's progressive scanning function, you may find that the picture and sound are out of sync. With the A/V Sync setting, you can correct this by HDMI Lip Sync is enabled (➔ 61) and your TV or display supports HDMI Lip Sync, the displayed delay time will be the summation of the
  • Onkyo DTR-40.2 | Instruction Manual - Page 58
    appropriate progressive signal and reproduces the natural quality of the original picture. When the "Film Mode" setting is set to "Auto", the AV receiver automatically detects the picture source and in either "3:2" or "2:2". However, there may be times when you will get a better picture by setting
  • Onkyo DTR-40.2 | Instruction Manual - Page 59
    26). *2 Press CLR if you want to reset to the default value. Listening Mode Preset You mode specified here will be resumed once the AV receiver has been set to Standby. Main menu Listening jack, you can assign only listening modes for the analog sound to "PORT" selector. 2 Use R/X to select the
  • Onkyo DTR-40.2 | Instruction Manual - Page 60
    ). Hardware Setup Main menu Hardware Setup Remote ID ■ Remote ID 1, 2, or 3 When several Integra/Onkyo components are used in the same room, their remote ID codes may overlap. To differentiate the AV receiver from the other components, you can change its remote ID from "1", to "2" or "3". Note
  • Onkyo DTR-40.2 | Instruction Manual - Page 61
    , no sound may be receiver. • Set to "Off" when a connected piece of equipment is not com- patible or it is unclear whether the equipment is compatible or not. • If movement is unnatural when set to "On", change the setting to "Off". • Refer to the connected component's instruction manual
  • Onkyo DTR-40.2 | Instruction Manual - Page 62
    "On". • HDMI power control only works with Q-compatible components that support it and may not work properly with some components due to their instruction manual for details. ■ TV Control  Off: TV Control disabled.  On: TV Control enabled. Set to "On" when you want to control the AV receiver
  • Onkyo DTR-40.2 | Instruction Manual - Page 63
    Firmware Update Note • Perform the firmware update only when an announcement is posted on the Integra web site. • It takes about 30 minutes to complete the firmware update. ■ Version The current version of the firmware is displayed. ■ Receiver  via NET: You can update the firmware via Internet.
  • Onkyo DTR-40.2 | Instruction Manual - Page 64
    playing and the intention of the original sound designer, and with some material there will be used with the following listening modes: THX Cinema, THX Surround EX, and THX Select2 Cinema. Note • Settings for the sent to the HDMI OUT MAIN of the AV receiver.*1 With this selection the TV's audio can be
  • Onkyo DTR-40.2 | Instruction Manual - Page 65
    Audio Selector" setting. Normally, the AV receiver detects the signal format automatically. However, when playing PCM or DTS material, you can manually set the signal format to PCM or DTS. be no sound. Note • The setting is stored individually for each input selector. • The setting will be reset to "
  • Onkyo DTR-40.2 | Instruction Manual - Page 66
    . Consult your ISP if you have any problems with your Internet connection. • The AV receiver uses DHCP to configure its network settings automatically. If you want to configure these settings manually, see "Network Settings" (➔ 72). • The AV receiver does not support PPPoE settings, so if you have
  • Onkyo DTR-40.2 | Instruction Manual - Page 67
    onkyo.vtuner.com/ portal. To verify your MAC Address, please see "Network Settings" (➔ 72). Display Note • When the NETWORK indicator flashes, confirm that the Ethernet cable is firmly connected to the AV receiver. • Services available may vary depending on the region. See the separate instructions
  • Onkyo DTR-40.2 | Instruction Manual - Page 68
    files on a computer or media server through the AV receiver. See "Supported Audio File Formats" to "About DLNA" for details on supported music servers and music file formats. For Windows Media® NETWORK indicator flashes, confirm the net- work connection. • To update the screen, press Return. En 68
  • Onkyo DTR-40.2 | Instruction Manual - Page 69
    • The search function does not work with media servers which do not support this function. • Depending on the sharing settings in the media server, the AV receiver may not able to access the content. Refer to the instruction manual of the media server. 4 Use R/X to select an item, and then press
  • Onkyo DTR-40.2 | Instruction Manual - Page 70
    Audio File Formats For server playback, the AV receiver supports the following music file formats: MP3, WMA, WAV, FLAC, Ogg Vorbis, AAC and LPCM. Not all servers support all formats. ■ MP3 • MP3 files must be MPEG-1/MPEG-2 Audio Layer 3 for- mat with a sampling rate of 8 kHz, 11.025 kHz, 12
  • Onkyo DTR-40.2 | Instruction Manual - Page 71
    Server Requirements The AV receiver can play digital music files stored on a computer or media server and supports the following technologies: • Windows Setting varies depending on the device. Refer to your device's instruction manual for details. If the operating system of your personal computer
  • Onkyo DTR-40.2 | Instruction Manual - Page 72
    volume in the AV receiver will not be reflected in the "Remote Playback" window. Windows and the Windows logo are trademarks of the Microsoft group of companies. En 72 7. Hardware Setup 1. Remote ID 2. Multi Zone 3. Tuner 4. HDMI 5. Auto Power Down 6. Network 7. Firmware Update 3 Use R/X to select
  • Onkyo DTR-40.2 | Instruction Manual - Page 73
    's MAC (Media Access Control) address. This address cannot be changed. ■ DHCP This setting determines whether or not the AV receiver uses DHCP to automatically configure its IP Address, Subnet Mask, Gateway, and DNS Server settings.  Enable: DHCP enabled.  Disable: DHCP disabled. If you select
  • Onkyo DTR-40.2 | Instruction Manual - Page 74
    Audio File Formats For USB mass storage device playback, the AV receiver supports music file formats. See "Supported Audio File Formats" (➔ 70). USB Mass Storage Device Requirements • The AV receiver supports USB devices that support the USB mass storage device class. • Playback may not be possible
  • Onkyo DTR-40.2 | Instruction Manual - Page 75
    played through the AV receiver in this way. • The AV receiver supports USB MP3 players that support the USB Mass Storage support the USB Mass Storage Class standard. Refer your USB MP3 player's instruction manual for details. • Protected WMA music files on an MP3 player cannot be played. • Onkyo
  • Onkyo DTR-40.2 | Instruction Manual - Page 76
    Zone 2" setting to "Act" (➔ 77). TV Hookup • Connect your Zone 2 speakers to the AV receiver's FRONT WIDE/ZONE 2 L/R terminals. AV receiver Main room TV AV receiver Zone 2 IN R L Receiver/ integrated amp Zone 2 R Note • With the default settings, the Zone 2 volume must be set on the
  • Onkyo DTR-40.2 | Instruction Manual - Page 77
    receiver features a composite video output for connection to a TV in Zone 2, so you can enjoy both audio and video in that zone. Hookup • Use a composite video cable to connect the AV receiver to "Bi-AMP" (➔ 50). • This procedure can also be performed on the AV receiver by using Setup, arrows, and Enter.
  • Onkyo DTR-40.2 | Instruction Manual - Page 78
    AV receiver Zone 2 indicator 7. Hardware Setup 1. Remote ID 2. Multi Zone 3. Tuner 4. HDMI 5. Auto Power Down 6. Network 7. Firmware Update 3 set on the amp in that zone.  Variable: The Zone 2 volume can be set on the AV receiver. If you've connected your Zone 2 speakers to an amp with no volume
  • Onkyo DTR-40.2 | Instruction Manual - Page 79
    WIDE/ZONE 2 L/R terminals. Digital input sources are not output. If no sound is heard when an input source is selected, check if it's connected to When you connect Zone 2 speakers directly to the AV receiver, listening modes that require surround back speakers or front high speakers or front wide
  • Onkyo DTR-40.2 | Instruction Manual - Page 80
    max. at TRIGGER OUT A; +12 volts and 25 milliamperes max. at TRIGGER OUT B and C). Hookup • Use a miniplug cable to connect the AV receiver's 12V TRIGGER OUT A, B, or C jack to the 12 V trigger input on a connected component. When several components are turned on simultaneously by using triggers
  • Onkyo DTR-40.2 | Instruction Manual - Page 81
    , as shown below. The IR IN A and B jacks are identical. Up to two IR receivers can be connected. From the Connecting block Miniplug cable AV receiver IR IN A or B IR OUT Connecting block AV receiver IR receiver IR Emitter Remote controller Other component Signal flow The IR emitter should be
  • Onkyo DTR-40.2 | Instruction Manual - Page 82
    Display again switches back to Standard Mode. *2 The following iPod models are not supported in Stan- dard Mode. These iPod models can only be controlled in Extended Mode. *3 When you disconnect the iPod/iPhone, the AV receiver stores the mode. This means that if you disconnect when in Extended Mode
  • Onkyo DTR-40.2 | Instruction Manual - Page 83
    *4 • Artists*4 • Albums*4 Connecting an Onkyo Dock • Genres*4 • Songs*4 • Composers information about currently playing track. *1 " # No. Onkyo Dock " UP-A1 Dock (Universal Port Option Dock) -A1 Dock's instruction manual for more information. • See the RI Dock's instruction manual for more 84
  • Onkyo DTR-40.2 | Instruction Manual - Page 84
    Apple web site. For supported iPod models, see the instruction manual of the Onkyo Dock. UP-A1 Dock With the UP-A1 Dock, you can easily play the music, photo, or movie stored on your Apple iPod through the AV receiver and enjoy great sound. You can use the AV receiver's remote controller to operate
  • Onkyo DTR-40.2 | Instruction Manual - Page 85
    on your iPod to start playback, the AV receiver will automatically turn on at the specified time video playback or when the alarm is set to play a sound. • If you use your iPod with any other accessories, control code (➔ 88). See the Dock's instruction manual for more information. ■ UP-A1 Dock Port
  • Onkyo DTR-40.2 | Instruction Manual - Page 86
    of the iPod, please refer to the instruction manual of RI Dock. *1 This button does not turn the Onkyo DS-A2 or DS-A2X RI Dock on Note • In Extended mode (see *2), the playback will be continued even if the AV receiver is turned off. • In Extended mode (see *2), you cannot operate your iPod directly
  • Onkyo DTR-40.2 | Instruction Manual - Page 87
    pages indicated. BD/DVD Integra/Onkyo Blu-ray Disc player (➔ 89) TV/CD Integra/Onkyo CD player (➔ 89) Port Onkyo Universal Port Option (➔ 85 This setting can not be carried out by using the AV receiver's display. 1 Press Receiver followed by Setup. The main menu appears onscreen. Sonawa Sonber
  • Onkyo DTR-40.2 | Instruction Manual - Page 88
    a cassette tape deck connected via V, press and hold TV/CD to switch to TAPE. 3 Press Remote Mode, point the remote controller at the AV receiver, and operate the component. If you want to control an Integra/Onkyo component by pointing the remote controller directly at it, or you want to control an
  • Onkyo DTR-40.2 | Instruction Manual - Page 89
    Q and be connected to the AV receiver via HDMI. *1 The Q supported by the AV receiver is the CEC system control function of the HDMI standard. Resetting the Remote Controller You can reset the remote controller to its default settings. 1 While holding down Receiver, press and hold down Home until
  • Onkyo DTR-40.2 | Instruction Manual - Page 90
    receiver CD player/CD recorder MD recorder Cassette tape deck B J B Buttons B On, Standby ✔ ✔ C , Input, ✔ TV VOL R/X D Guide ✔ Top Menu ✔ Return O CLR *1 The Q function is not supported. The Q sup- H ported by the AV receiver is the CEC system control function of the
  • Onkyo DTR-40.2 | Instruction Manual - Page 91
    AV receiver's remote Stop, Pause, and so on are preprogrammed with commands for controlling Onkyo CD players, cassette decks, and DVD players. However, they can and you can restore the preprogrammed commands at any time by resetting the remote controller (➔ 89). • To overwrite a previously learned
  • Onkyo DTR-40.2 | Instruction Manual - Page 92
    is deleted (➔ 27). • When you using Normal macro mode, you cannot use the easy macro command including the change of the source component. Receiver 1 While holding down Receiver, press and hold down My Movie, My TV or My Music until My Movie, My TV, or My Music lights (about 3 seconds). 2 Press
  • Onkyo DTR-40.2 | Instruction Manual - Page 93
    Others Troubleshooting If you have any trouble using the AV receiver, look for a solution in this section. If you can't resolve the issue yourself, contact the dealer from whom you purchased this unit. If you can't resolve the issue yourself, try resetting the AV receiver before contacting the
  • Onkyo DTR-40.2 | Instruction Manual - Page 94
    forward, or fast reverse function on your player. If you switch your player from DTS to PCM, because the AV receiver does not switch formats immediately, you may not hear any sound, in which case you should stop your player for about three seconds, and then resume playback. With some CD and
  • Onkyo DTR-40.2 | Instruction Manual - Page 95
    message "Resolution Error" appears on the - AV receiver's display, this indicates that your TV does not support the current video resolution and you need to ID on both the AV receiver 60 and remote controller. ■ Can't control other components If it's an Integra/Onkyo component, make sure that 20
  • Onkyo DTR-40.2 | Instruction Manual - Page 96
    receiver. Be sure to enter the appropriate remote control code first. To control an Integra/Onkyo that contain several instructions. Recording ■ Can sound Powered Zone 2 cannot be used if "Speakers 50 Type(Front)" is set to "Bi-Amp - The AV receiver supports USB devices that support - the USB
  • Onkyo DTR-40.2 | Instruction Manual - Page 97
    analog audio connection (RCA) between the component and AV receiver, even if they are connected digitally. While Zone 2 is speaker unit. Check if the unit produces normal sounds. ■ The following settings can be made for and then plug it back in again. Onkyo is not responsible for damages (such as
  • Onkyo DTR-40.2 | Instruction Manual - Page 98
    kHz (Australian) 522/530 kHz - 1611/1710 kHz Preset Channel 40 Digital Tuner (North American) SIRIUS General Power Supply (North American) 13/16" Weight 12.5 kg (27.6 lbs.) ■ HDMI Input Output Video Resolution Audio Format Supported IN 1, IN 2, IN 3, IN 4, IN 5, IN 6, AUX INPUT OUT MAIN,
  • Onkyo DTR-40.2 | Instruction Manual - Page 99
    , SBR, FHL, FHR) + ZONE2/Front Wide (L, R) Phones 1 (6.3 ø) ■ Others SETUP MIC 1 RS232 1 Ethernet 1 IR Input 2 IR Output 1 12 V Trigger Out 3 USB 1 Universal Port 1 RI 1 Specifications and features are subject to change without notice. En 99
  • Onkyo DTR-40.2 | Instruction Manual - Page 100
    PC are not supported. • The HDMI audio signal (sampling rate, bit length, etc.) may be restricted by the connected source component. If the picture is poor or there's no sound from a component connected via HDMI, check its setup. Refer to the connected component's instruction manual for details. En
  • Onkyo DTR-40.2 | Instruction Manual - Page 101
    TV, Player, or Recorder Q, which stands for Remote Interactive over HDMI, is the name of the system control function found on Integra/ Onkyo components. The AV receiver can be used with CEC (Consumer Electronics Control), which allows system control over HDMI and is part of the HDMI standard. CEC
  • Onkyo DTR-40.2 | Instruction Manual - Page 102
    -ray Disc/DVD player/recorder connected is selected. • The power of the TV is turned on automatically, and input with the AV receiver connected is selected. 5. Following the operating instructions of the TV, select "Use the TV speakers" from the menu screen of the TV, and confirm that the audio is
  • Onkyo DTR-40.2 | Instruction Manual - Page 103
    Video Resolution Chart The following tables show how video signals at different resolutions are output by the AV receiver. NTSC/PAL ✔: Output Input Output HDMI 1080p 1080i 720p HDMI 1080p ✔ 1080i ✔ ✔ ✔ 720p ✔ ✔ ✔ 480p/576p ✔ ✔ ✔ 480i/576i ✔ ✔ ✔ Component 1080p ✔ 1080i ✔ ✔
  • Onkyo DTR-40.2 | Instruction Manual - Page 104
    Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 800-225-1946, 201-818-9200 Fax: 201-785-2650 http://www.integrahometheater.com Integra Division of ONKYO CORPORATION Sales & Product Planning Div.: 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8163 En Y1005
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
AV Receiver
DTR-40.2
Instruction Manual