Onkyo HT-RC440 Owner Manual - Page 26

Listening to AM/FM Radio, En-26

Get Onkyo HT-RC440 PDF manuals and user guides View all Onkyo HT-RC440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Listening to AM/FM Radio This section describes the procedure of using the buttons on the front panel, unless otherwise specified. Using the Tuner With the built-in tuner you can enjoy AM and FM radio stations. You can store your favorite stations as presets for quick selection. You can also change the frequency steps (➔ page 46). 1 Press AM or FM to select either "AM" or "FM". In this example, FM has been selected. Band Frequency (Actual display depends on the country.) Tuning into Radio Stations ■ Auto tuning mode 1 Press TUNING MODE so that the AUTO indicator lights on the AV receiver's display. 2 Press TUNING R/X. Searching stops when a station is found. When tuned into a station, the TUNED indicator lights. When tuned into a stereo FM station, the FM STEREO indicator lights as shown. TUNED AUTO FM STEREO Tip • Tuning into weak FM stereo stations If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to manual tuning mode and listen to the station in mono. Turning On & Basic Operations ■ Manual tuning mode In manual tuning mode, FM stations will be in mono. 1 Press TUNING MODE so that the AUTO indicator goes off on the AV receiver's display. 2 Press and hold TUNING R/X. The frequency stops changing when you release the button. Press the buttons repeatedly to change the frequency one step at a time. ■ Tuning into stations by frequency You can tune into AM and FM stations directly by entering the appropriate frequency. 1 On the remote controller, press AM or FM to select "AM" or "FM", followed by D.TUN. (Actual display depends on the country.) 2 Within 8 seconds, use the number buttons to enter the frequency of the radio station. For example, to tune to 87.5 (FM), press 8, 7, 5 or 8, 7, 5, 0. If you have entered the wrong number, you can retry after 8 seconds. En-26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
Turning On & Basic Operations
En-26
Using the Tuner
With the built-in tuner you can enjoy AM and FM radio
stations. You can store your favorite stations as presets for
quick selection.
You can also change the frequency steps (
➔
page 46
).
Tuning into Radio Stations
■
Auto tuning mode
■
Manual tuning mode
In manual tuning mode, FM stations will be in mono.
■
Tuning into stations by frequency
You can tune into AM and FM stations directly by entering
the appropriate frequency.
Listening to AM/FM Radio
This section describes the procedure of using the
buttons on the front panel, unless otherwise specified.
1
Press
AM
or
FM
to select either “AM” or “FM”.
In this example, FM has been selected.
(Actual display depends on the country.)
Band
Frequency
1
Press
TUNING MODE
so that the AUTO indicator
lights on the AV receiver’s display.
2
Press
TUNING
q
/
w
.
Searching stops when a station is found.
When tuned into a station, the
TUNED
indicator
lights. When tuned into a stereo FM station, the
FM
STEREO
indicator lights as shown.
Tip
•
Tuning into weak FM stereo stations
If the signal from a stereo FM station is weak, it may be
impossible to get good reception. In this case, switch to
manual tuning mode and listen to the station in mono.
TUNED
FM STEREO
AUTO
1
Press
TUNING MODE
so that the AUTO indicator
goes off on the AV receiver’s display.
2
Press and hold
TUNING
q
/
w
.
The frequency stops changing when you release the
button.
Press the buttons repeatedly to change the frequency
one step at a time.
1
On the remote controller, press
AM
or
FM
to select
“AM” or “FM”, followed by
D.TUN
.
(Actual display depends on the country.)
2
Within 8 seconds, use the number buttons to enter
the frequency of the radio station.
For example, to tune to 87.5 (FM), press
8
,
7
,
5
or
8
,
7
,
5
,
0
.
If you have entered the wrong number, you can retry
after 8 seconds.