Onkyo HT-RC440 Owner Manual - Page 64

En-64, Updating the Firmware via USB - firmware update

Get Onkyo HT-RC440 PDF manuals and user guides View all Onkyo HT-RC440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Updating the Firmware via USB The AV receiver allows you to update the firmware using a USB device. Note • Never unplug or turn off the AV receiver during the update process. • Never plug or unplug an HDMI cable or a USB device during the update process. • Never unplug the USB storage device containing the firmware file or the AC power cord during the update process. • Do not attempt to access the AV receiver from your PC while it is being updated. • It takes up to 10 minutes to complete the firmware update. • The AV receiver will retain all your settings after the update is finished. Before you start • Set the "HDMI Ctrl (RIHD)" setting to "Off" (➔ page 47). • Turn off the controller device connected via Ethernet cable. • Turn off Multi Zone if this function is present. • Stop playback of contents from Internet Radio, iPod/iPhone, USB or servers, etc. • If there is any data in the USB device, remove it first. Update procedure 1 Connect a USB device to your PC. If there is any data in the USB device, remove it first. 2 Download the firmware file from the Onkyo web site. The file name is as follows: ONKAVR zip Unzip the downloaded file. The following three files are created: ONKAVR of1 ONKAVR of2 ONKAVR of3 3 Copy the extracted files to the USB device. Be careful not to copy the zip file. 4 Remove the USB device from your PC and connect it to the USB port on the AV receiver. 5 Make sure the AV receiver and TV are turned on. If the AV receiver is in standby mode, press ON/STANDBY on the AV receiver to light up the front display. 6 Select the USB input source. "Now Initializing..." appears on the AV receiver's display and then the name of the USB device is displayed. It takes 20 to 30 seconds to recognize the USB device. 7 Press RECEIVER followed by HOME on the remote controller. The Home menu appears on the TV screen. 8 Select "F/W Update" and press ENTER. Appendix 9 Select "Update via USB" and press ENTER. Note that this option will not be available if there is no firmware file newer than the currently installed version. 10 Select "Update" and press ENTER. The update process will begin. During the update process, the on-screen display may disappear depending on the updated program. When this occurs, you can still view the update progress on the AV receiver's display. The on-screen display will reappear after the update is complete, and upon turning the AV receiver off and on again. Do not turn off the AV receiver and do not remove the USB device during the update process. 11 The message "Completed!" appears on the AV receiver's display, indicating that the update has been completed. Remove the USB device. 12 Turn off the AV receiver using ON/STANDBY on the front panel. Do not use RECEIVER on the remote controller. Once turned off, the AV receiver will automatically turn on again. Congratulations! You now have the latest firmware installed on your Onkyo AV receiver. En-64

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
Appendix
En-64
The AV receiver allows you to update the firmware using a
USB device.
Note
•
Never unplug or turn off the AV receiver during the update
process.
•
Never plug or unplug an HDMI cable or a USB device during the
update process.
•
Never unplug the USB storage device containing the firmware
file or the AC power cord during the update process.
•
Do not attempt to access the AV receiver from your PC while it
is being updated.
•
It takes up to 10 minutes to complete the firmware update.
•
The AV receiver will retain all your settings after the update is
finished.
Before you start
• Set the “
HDMI Ctrl (RIHD)
” setting to “
Off
”
(
➔
page 47
).
• Turn off the controller device connected via Ethernet
cable.
• Turn off Multi Zone if this function is present.
• Stop playback of contents from Internet Radio,
iPod/iPhone, USB or servers, etc.
• If there is any data in the USB device, remove it first.
Update procedure
Updating the Firmware via USB
1
Connect a USB device to your PC. If there is any
data in the USB device, remove it first.
2
Download the firmware file from the Onkyo web
site. The file name is as follows:
ONKAVR****_************.zip
Unzip the downloaded file. The following three files
are created:
ONKAVR****_************.of1
ONKAVR****_************.of2
ONKAVR****_************.of3
3
Copy the extracted files to the USB device. Be
careful not to copy the zip file.
4
Remove the USB device from your PC and connect
it to the
USB
port on the AV receiver.
5
Make sure the AV receiver and TV are turned on.
If the AV receiver is in standby mode, press
8
ON/STANDBY
on the AV receiver to light up the
front display.
6
Select the USB input source.
“
Now Initializing...
” appears on the AV receiver’s
display and then the name of the USB device is
displayed. It takes 20 to 30 seconds to recognize the
USB device.
7
Press
RECEIVER
followed by
HOME
on the remote
controller.
The Home menu appears on the TV screen.
8
Select “F/W Update” and press
ENTER
.
9
Select “Update via USB” and press
ENTER
.
Note that this option will not be available if there is no
firmware file newer than the currently installed
version.
10
Select “Update” and press
ENTER
.
The update process will begin.
During the update process, the on-screen display may
disappear depending on the updated program. When
this occurs, you can still view the update progress on
the AV receiver’s display. The on-screen display will
reappear after the update is complete, and upon
turning the AV receiver off and on again.
Do not turn off the AV receiver and do not remove the
USB device during the update process.
11
The message “Completed!” appears on the AV
receiver’s display, indicating that the update has
been completed.
Remove the USB device.
12
Turn off the AV receiver using
8
ON/STANDBY
on
the front panel.
Do not use
8
RECEIVER
on the remote controller.
Once turned off, the AV receiver will automatically
turn on again.
Congratulations! You now have the latest firmware
installed on your Onkyo AV receiver.