Onkyo HT-S6300 Owner Manual - Page 58

■ Charging Your iPod models Battery The UP-A1 Dock charges your iPod models battery while your iPod is in the UP-A1 Dock and connected to the UNIVERSAL PORT jack on the AV receiver. While your iPod is seated in the UP-A1 Dock, its battery will be charged when the AV receiver is set to "On" or "Standby". Note • When UP-A1 Dock that seated iPod is connected, the power consumption on standby mode slightly increases. ■ Status Messages • PORT Reading The AV receiver is checking the connection with the dock. • PORT Not Support The AV receiver do not support the connected dock. • PORT UP-A1 UP-A1 Dock is connected. Note • The AV receiver displays the message "UP-A1" for several sec- onds after recognizing the UP-A1. • When the status message is not displayed on the AV receiver's display, check the connection to your iPod. RI Dock RI Dock is sold separately. For supported iPod models, see the instruction manual of the RI Dock. With the RI Dock, you can easily play the music stored on your Apple iPod through the AV receiver and enjoy great sound, and watch iPod slideshows and videos on your TV. In addition, the onscreen display (OSD) allows you to view, navigate, and select your iPod model's contents on your TV, and with the supplied remote controller, you can control your iPod from the comfort of your sofa. You can even use the AV receiver's remote controller to operate your iPod. Note • Enter the appropriate remote control code before using the AV receiver's remote controller for the first time (➔ 61). • Connect the RI Dock to the AV receiver with an V cable (➔ 56). • Set the RI Dock's RI MODE switch to HDD or HDD/DOCK. • Set the AV receiver's Input Display to "DOCK" (➔ 27). ■ System Function System On When you turn on the AV receiver, the RI Dock and iPod turn on automatically. In addition, when the RI Dock and iPod are on, the AV receiver can be turned on by pressing ON/STANDBY. Auto Power On If you press the remote controller's  while the AV receiver is on Standby, the AV receiver will automatically turn on, select your iPod as the input source, and your iPod will start playback. Direct Change If you start iPod playback while listening to another input source, the AV receiver will automatically switch to the input to which the RI Dock is connected. Other Remote Controllers You can use the remote controller that came with the AV receiver to control other iPod functions. The available functionality depends on the AV receiver. iPod Alarm If you use the Alarm function on your iPod to start playback, the AV receiver will turn on at the specified time and select your iPod as the input source automatically. Note • Linked operations do not work with video playback or when the alarm is set to play a sound. • If you use your iPod with any other accessories, iPod playback detection may not work. • This function only works when the Standard mode is set to On. ■ Operating Notes • Use the AV receiver's volume control to adjust the playback volume. • While your iPod is inserted in the RI Dock, its volume control has no effect. • If you do adjust the volume control on your iPod while it's inserted in the RI Dock, be careful that it's not set too loud before you reconnect your earphones. Controlling Your iPod By pressing REMOTE MODE that's been programmed with the remote control code for your Dock, you can control your iPod in the Dock with the following buttons. See "Remote Control Codes for Onkyo Components Connected via V" for details on entering a remote control code (➔ 61). See the Dock's instruction manual for more information. ■ UP-A1 Dock PORT is preprogrammed with the remote control code for controlling a Dock with Universal Port connector. You can control your iPod when PORT is selected as the input source. Without the RI Control You must enter a remote control code 82990 first (➔ 61). ■ RI Dock • Set the RI Dock's RI MODE switch to HDD or HDD/ DOCK. • ON/STANDBY may not work with a remote control code (without V). In this case, make an V connection and enter a remote control code 81993 (with V). With the RI Control In this case, make an V connection and enter a remote control code 81993 (with V). • Set the AV receiver's Input Display to "DOCK" (➔ 27). En 58