Onkyo HT-S670 Owner Manual
Onkyo HT-S670 Manual
 |
View all Onkyo HT-S670 manuals
Add to My Manuals
Save this manual to your list of manuals |
Onkyo HT-S670 manual content summary:
- Onkyo HT-S670 | Owner Manual - Page 1
HT-R420 Instruction Manual Thank you for purchasing an Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual with your other AV components 33 Appendix Troubleshooting 38 Specifications back cover page En - Onkyo HT-S670 | Owner Manual - Page 2
the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near - Onkyo HT-S670 | Owner Manual - Page 3
cable ground shall be connected to the grounding system of the building, as close to the used in accordance with the instructions, may cause harmful interference HT-R420 is not userserviceable. If you cannot turn on the HT-R420, contact your Onkyo dealer. 3. Care-Occasionally you should dust the HT - Onkyo HT-S670 | Owner Manual - Page 4
trademarks of Dolby Laboratories. ** "DTS" and "DTS Digital Surround" are registered trademarks of Digital Theater Systems, Inc. Supplied accessories Check that the following accessories are supplied with the HT-R420. AM loop antenna × 1 FM indoor antenna × 1 (Connect type varies from country to - Onkyo HT-S670 | Owner Manual - Page 5
HT-R420 Setting the Voltage Selector (Worldwide model only) The Worldwide model has a voltage selector for compatibility with power systems remote controller of the same type is used in the same room, or the HT-R420 is installed close to equipment that uses infrared rays, the remote controller - Onkyo HT-S670 | Owner Manual - Page 6
$ %^ For operational instructions, refer to the page to the DIGITAL INPUT jacks of the HT-R420, use this button to assign the the DSP button to recall the Onkyo-original DSP modes in sequence. speaker system A/B. The (SPEAKERS) A/B indicators corresponding to the selected speaker system light - Onkyo HT-S670 | Owner Manual - Page 7
treble, late night function, cinema filter, Panorama, Dimension and Center Width function setting. a (SPEAKERS) A/B indicators [17, 24] Shows the current speaker system in use. b MUTING indicator [24] Flashes when the mute function is active. c Source/Listening mode indicators [17, 29] One of these - Onkyo HT-S670 | Owner Manual - Page 8
The audio input jacks of the HT-R420 do not accept direct connection of an analog turnable. If you want to connect a turntable to the HT-R420 prepare a phono equalizer and connect it to the unused audio input jacks (IN L/R). Refer to the instruction manuals of the phono equalizer and turntable for - Onkyo HT-S670 | Owner Manual - Page 9
the HT-R420. To operate other components, see "Using the remote controller with your other AV components" on pages 33 through 37. For operational instructions, three. ~ SP A/SP B buttons [17, 24] Press to switch the speaker systems. ! AUDIO ADJUST button [30] Press to adjust bass, treble, late night - Onkyo HT-S670 | Owner Manual - Page 10
equipment Before connecting • Be sure to always refer to the instruction manual that came with the component that you are connecting. • Do . Improper connection Video Connection Formats Video equipment can be connected to the HT-R420 using the following video connection formats : Video or S Video, - Onkyo HT-S670 | Owner Manual - Page 11
player has both 5.1 channel audio outputs and 2 channel audio outputs, and you want to connect the DVD player only using the FRONT L/R jacks on the HT-R420, use the 2 channel audio output jacks on the DVD player. If the DVD player only has the 2 channel audio outputs, connect it to the - Onkyo HT-S670 | Owner Manual - Page 12
the sounds such as Dolby surround and DTS surround. The speaker system B consists of the FRONT SPEAKERS B. You can reproduce only monaural one-third the length of the room. Refer to the speakers' instruction manuals for details. Front left speaker TV/Screen Front right speaker Subwoofer Center - Onkyo HT-S670 | Owner Manual - Page 13
Refer also to the instruction manuals of the speakers. one speaker cable to one speaker terminal. Doing so may damage the HT-R420. • When you are using only one speaker or when you to the speaker terminals 3/8" (10 mm) Connecting to the speaker system B Strip 3/8" (10 mm) from the end of each cable - Onkyo HT-S670 | Owner Manual - Page 14
for indoor use only. Set it in the direction and position where you receive signals clearly. Put it as far away as possible from the HT-R420, televisions, speaker cables, and power cords. When reception is not satisfactory with the attached AM loop antenna alone, connection of an outdoor antenna is - Onkyo HT-S670 | Owner Manual - Page 15
socket. Using a TV/FM Antenna Splitter It's best not to use the same antenna for both FM and TV reception, as this can cause interference problems. If circumstances demand it, use a TV/FM antenna splitter, as shown. Connecting 300-ohm Flat Cable 1. Using a screwdriver, loosen the two screws on the - Onkyo HT-S670 | Owner Manual - Page 16
HT-R420 at the sensor on the HT-R420 and operate that component without having to switch remote controllers. In addition, by connecting components to the z terminal, you can also perform the system the HT-R420. The other one can be used to daisy chain with another component. • With Onkyo DVD players - Onkyo HT-S670 | Owner Manual - Page 17
the power 1. Connect the power cord to a wall outlet. The HT-R420 enters standby mode. The STANDBY indicator lights up. 2. Press STANDBY on the unit or SP A/ SP B on the remote controller to select the speaker system(s) to be used. 3. Start playing the selected source. See page 22 to listen to - Onkyo HT-S670 | Owner Manual - Page 18
is 80 Hz. Home theater in a box (HT-S670) It is not neccessary to change this setting when using the supplied speaker system. If you're 120 Hz 150 Hz If you want more accurate setting, refer to the instruction manuals of the speakers and perform the setting according to their frequency response. - Onkyo HT-S670 | Owner Manual - Page 19
Speaker setup SPEAKER ADJUST PRESET/ADJUST ™/£ Specifying speaker distances To get the best from surround sound, it's important that the sound from each speaker reaches the listener at the same time. To achieve this, you need to specify the distance from each speaker to the listening position. - Onkyo HT-S670 | Owner Manual - Page 20
Speaker setup SUBWOOFER MODE TEST CH SEL These buttons may be in a slightly different position on your remote controller. LEVEL 5/∞ Setting the subwoofer mode Press SUBWOOFER MODE on the unit. With the first press of the button, you can check the present setting. Then each press of the button - Onkyo HT-S670 | Owner Manual - Page 21
Changing the default settings according to your connections If equipment couldn't be connected in accordance with the default settings, or your preferred settings differ from the default settings, you can change the settings as described below. DIGITAL INPUT DVD TAPE Switch the source from TAPE - Onkyo HT-S670 | Owner Manual - Page 22
Listening to the radio There are two ways to select radio stations: • Manual tuning • Presetting radio stations then selecting the preset channels TUNING ™/£ FM MODE TUNER Tuning into a radio station 1. Press TUNER. The selected band appears in the - Onkyo HT-S670 | Owner Manual - Page 23
Listening to the radio FM MODE MEMORY PRESET/ADJUST ™/£ PRESET 2/3 These buttons may be in a slightly different position on your remote controller. TUNER Presetting radio stations You can preset up to 30 stations. 1. Tune in the radio station you wish to preset (refer to the previous page). 2. - Onkyo HT-S670 | Owner Manual - Page 24
listening mode other than "Direct" is selected, the listening mode is set to "Stereo.") The lit (speaker) A/B indicators indicate the corresponding speaker systems are on. Muting the sound (remote controller only) Press MUTING. The MUTING indicator flashes in the display during the muting mode. To - Onkyo HT-S670 | Owner Manual - Page 25
Various functions common to all the sources DISPLAY DIMMER SLEEP DIMMER These buttons may be in a slightly different position on your remote controller. Changing the display Press DISPLAY. Each time you press DISPLAY, the screen changes as follows: When an input source other than FM or AM is - Onkyo HT-S670 | Owner Manual - Page 26
source. ** "Multich" can be selected only when DVD is selected as the input source. To fix the "Auto" to DTS or PCM If there is a problem as described below, it is possible to fix the "Auto" to PCM or DTS. • If the beginning of each PCM track is cut in Auto - Onkyo HT-S670 | Owner Manual - Page 27
Using analog multi channel input The multi channel input refers to a system, which is compatible with a source component equipped with analog 5.1- Check that the DVD player is set for multi channel output. See instruction manual supplied with your DVD player for details. 4. If necessary, press CH - Onkyo HT-S670 | Owner Manual - Page 28
instructions, refer to the page 29. Following are the sound systems surround, DTS (Digital Theater System) surround This 5.1-channel jacks of the HT-R420 output analog audio. Do not record CDs or LDs that support DTS using these can enjoy unique surround modes to Onkyo as listed below. Orchestra This - Onkyo HT-S670 | Owner Manual - Page 29
DTS). A.STEREO button: Set the listening mode to "All Ch St". DSP button on the front panel: Recall the Onkyo-original DSP mode. Each time this button is pressed, the listening mode cycles; "Orchestra" → "Unplugged" → "Studio AC-3RF demodulator to one of the HT-R420's DIGITAL INPUT terminals. 29 - Onkyo HT-S670 | Owner Manual - Page 30
, press RCVR/TAPE. These functions only work with speaker system A. Audio Adjust provides various functions for adjusting the sound, Bass Treble Late Night Cinema Filter (Cine Fltr) Panorama Dimension Center Width Range Default Supported listening mode -12 dB to +12 dB 0 dB All modes except in 2 - Onkyo HT-S670 | Owner Manual - Page 31
or no effect. This function is automatically cancelled when you set the HT-R420 to Standby. Cinema Filter When this function is on, you output only by the front left and right speakers ("phantom" center). In home theaters, adding some width to the center channel can improve the balance between the - Onkyo HT-S670 | Owner Manual - Page 32
Recording a source To record the input source signal you are currently watching or listening to Recording of video and/or audio signals can be performed on the components connected to the VIDEO 1 OUT and TAPE OUT (audio only) jacks. Recording the video from one source and the audio from another - Onkyo HT-S670 | Owner Manual - Page 33
. See page 16 for connection information. Entering the manufacturer's code (RC-518M only) If you're using an Onkyo CD player connected to the HT-R420's z connector, an Onkyo AV component without an z connection, or an AV component made by another manufacturer, do the following. When you operate - Onkyo HT-S670 | Owner Manual - Page 34
GE GE • PANA GE • RCA GEMINI GENERAL INSTRUMENT G.I. GO VIDEO GOLD STAR HAMLIN HITACHI HUGHES NETWORK SYSTEM JERROLD JVC KENWOOD MACOM MAGNAVOX MARANTZ MITSUBISHI NEC OAK ONKYO PANASONIC PHILIPS PIONEER PRIMESTAR PROSCAN RCA S.ATLANTA SAMSUNG SHARP SHINTOM SONY TOCOM TOSHIBA YAMAHA ZENITH TV 227 - Onkyo HT-S670 | Owner Manual - Page 35
component is connected to the HTR420 via z, point the remote controller at the HT-R420. If not, point the remote controller at the AV component. (A cassette button to turn on the AV component. Point the remote controller at the HT-R420. (A cassette recorder can't be turned on or off from the remote - Onkyo HT-S670 | Owner Manual - Page 36
selectors RC-518M: CD mode can be used only with an Onkyo CD player, and you must enter the appropriate Onkyo CD player code (see page 33). : Power On/Off. mode, you can control the cassette recorder and fully control the HT-R420 at the same time. You must enter the appropriate manufacturer's - Onkyo HT-S670 | Owner Manual - Page 37
Using the remote controller with your other AV components (RC-518M) TV mode (TV) (RC-518M) Cable mode (CABLE/SAT) (RC-518M) Satellite mode (CABLE/SAT) 3. TV operation buttons 2. 1. TV 4. CABLE operation buttons Control VCR if appropriate VCR code has been entered 3. 2. CABLE/ SAT 4. - Onkyo HT-S670 | Owner Manual - Page 38
Troubleshooting Check the following guide for the possible cause of a problem before contacting service. Refer also to the respective instruction manuals • Disconnect the power cord, then connect it again. • Contact your Onkyo Service Center. • Disconnect the power cord, then connect it again. • - Onkyo HT-S670 | Owner Manual - Page 39
Troubleshooting and SUBWOOFER jacks. • See the instruction manual supplied with - your DVD player, and be plugged in order to charge the backup system. The memory preservation period after the unit has When incorrect operation is observed • The HT-R420 contains an internal microcomputer that performs - Onkyo HT-S670 | Owner Manual - Page 40
EUROPE ELECTRONICS GmbH Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.onkyo.net ONKYO CHINA LIMITED Units 2102-2107, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung, N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039 HOMEPAGE http:// - Onkyo HT-S670 | Owner Manual - Page 41
6 Adjustment 6 Appendix Caring for Your Speakers 6 Troubleshooting 7 Specifications 7 Thank you for purchasing an Onkyo home theater speaker package. Please read this manual thoroughly before using your new speakers. Following the instructions in this manual will enable you to obtain optimum - Onkyo HT-S670 | Owner Manual - Page 42
servicing) instructions in the literature accompanying the appliance. Important Safeguards 1. Read Instructions - All the safety and operating instructions type of power supply to your home, consult your appliance dealer or and disconnect the antenna or cable system. This will prevent damage to - Onkyo HT-S670 | Owner Manual - Page 43
normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of is not userserviceable. If power does not come on, contact your Onkyo authorized service station. 2. Care From time to time you should wipe off the - Onkyo HT-S670 | Owner Manual - Page 44
This control is used to adjust the volume of the subwoofer. D LINE INPUT This RCA input should be connected to the subwoofer preout on your HT-R420 AV receiver, amp, or other receiver with supplied RCA cable. Note: The Auto Standby function turns the subwoofer on when the input signal exceeds - Onkyo HT-S670 | Owner Manual - Page 45
left and right speakers These output the overall sound. Their role in a home theater is to provide a solid anchor for the sound image. They should be that the walls are strong enough to support the speaker's weight. The weight that mounting screws can support varies greatly depending on the wall - Onkyo HT-S670 | Owner Manual - Page 46
might interfere with other electrical equipment o the same circuit. If this is a problem, plug the SKW-420 into a different branch circuit. Adjustment Setting the Subwoofer are using a chemical cloth, always follow the instructions that come with the cloth. For dust accumulated on grilles, use a vacuum - Onkyo HT-S670 | Owner Manual - Page 47
%FDFNCFS 1. Troubleshooting Symptom There's on subwoofer entered Standby mode. your amp. On the HT-R420 Receiver, the subwoofer mode is Set the subwoofer mode cable away from the interference source. Make sure your audio system is grounded properly. Specifications ■ Powered Subwoofer (SKW- - Onkyo HT-S670 | Owner Manual - Page 48
@&OGN 1BHF 4VOEBZ %FDFNCFS 1. Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8124 ONKYO U.S.A. CORPORATION 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.onkyousa.com
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
 |
 |
Contents
Thank you for purchasing an Onkyo AV Receiver.
Please read this manual thoroughly before making
connections and plugging in the unit.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new AV Receiver. Please retain
this manual for future reference.
HT-R420
Appendix
Troubleshooting
..............................................
38
Specifications
...........................
back cover page
Remote controller
Using the remote controller with your other
AV components
............................................
33
Enjoying music or videos
Enjoying music or videos with the
HT-R420
.......................................................
17
Speaker setup
..................................................
18
Changing the default settings according
to your connections
......................................
21
Listening to the radio
......................................
22
Various functions common to all the sources ..
24
Enjoying multi channel sources
.....................
27
Enjoying the listening modes
.........................
28
Audio adjust function
.....................................
30
Recording a source
.........................................
32
Before using
Important safeguards
........................................
2
Precautions
........................................................
3
Features
.............................................................
4
Supplied accessories
.........................................
4
Before using the HT-R420
...............................
5
AV Receiver
Instruction Manual
Facilities and connections
Index to parts and controls
...............................
6
Connecting to audio/video equipment
...........
10
Positioning speakers/Connecting speakers
....
12
Connecting antennas
.......................................
14
Connections for remote control (
z
)
.............
16
E
n