Onkyo HT-S7300 Owner Manual
Onkyo HT-S7300 Manual
 |
View all Onkyo HT-S7300 manuals
Add to My Manuals
Save this manual to your list of manuals |
Onkyo HT-S7300 manual content summary:
- Onkyo HT-S7300 | Owner Manual - Page 1
1ch Home Theater System HT-S7300 AV Receiver (HT-R680) Speaker Package (HTP-780) Universal Port Option Dock for iPod® (UP-A1) HT-S6300 AV Receiver (HT-R680) Speaker Package (HTP-680) Universal Port Option Dock for iPod® (UP-A1) Instruction Manual Thank you for purchasing an Onkyo 7.1ch Home Theater - Onkyo HT-S7300 | Owner Manual - Page 2
user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Read these instructions. 2. Keep these instructions with the cart, stand, PORTABLE CART WARNING set 10 cm (4") away from the rear - Onkyo HT-S7300 | Owner Manual - Page 3
2. AC Fuse-The AC fuse inside the unit is not user-serviceable. If you cannot turn on the unit, contact your Onkyo dealer. 3. Care-Occasionally you should dust the unit all and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful - Onkyo HT-S7300 | Owner Manual - Page 4
, howling or slipping of sound may occur. To prevent HT-S6300 AV Receiver HT-R680 HT-R680 (➔ 8) Remote controller and two batteries (AA/R6) (➔ 5) Indoor FM antenna (➔ 22) AM loop antenna (➔ 22) Speaker setup microphone (➔ 28) Speaker Package HTP-680 Front speakers (SKF-680 L/R) (➔ 10) Center speaker - Onkyo HT-S7300 | Owner Manual - Page 5
below. Remote control sensor AV receiver Introduction Important Safety Instructions 2 Precautions 3 Speaker Precautions 4 Package Contents 4 Features 6 Front & Rear Panels 8 Speaker Package 10 Remote Controller 12 About Home Theater 13 Connections Connecting the AV Receiver 14 Turning On - Onkyo HT-S7300 | Owner Manual - Page 6
Features AV Receiver HT-R680 • 130 Watts/Channel @ 6 ohms • WRAT-Wide Range Amplifier Technology (5 Hz to 100 kHz bandwidth) • Optimum Gain Volume Circuitry • H.C.P.S. (High Current Power Supply) Massive High Power Transformer • HDMI (Ver.1.4 with Audio Return Channel, 3D), Deep- Color, x.v.Color*, - Onkyo HT-S7300 | Owner Manual - Page 7
130 W • 6-ohm impedance • Color-coded speaker terminals and speaker cable SKW-780 Bass Reflex Powered Subwoofer • 10" (25 cm) Cone • Output Level Control • Max. power: 290 W (Dynamic power) Universal Port Option Dock for iPod® (UP-A1) • Easily links iPod/iPhone models with Onkyo A/V Systems. En 7 - Onkyo HT-S7300 | Owner Manual - Page 8
each item. B ON/STANDBY button (➔ 24) C STANDBY indicator (➔ 24) D HDMI THRU indicator (➔ 49) E ZONE 2 indicator (➔ 54) F Remote control sensor DISPLAY button (➔ 25) N SETUP button (➔ 38) O TUNING, PRESET (➔ 30 to 31), arrow and ENTER buttons P RETURN button Q MASTER VOLUME control (➔ 25) R MUSIC - Onkyo HT-S7300 | Owner Manual - Page 9
audio jacks D HDMI IN and OUT jacks E FM ANTENNA jack and AM ANTENNA terminal F MONITOR OUT V jack G UNIVERSAL PORT jack H SPEAKERS terminals (BD/ OR ZONE 2 SPEAKERS terminals (CENTER, FRONT, SURR and SURR BACK OR FRONT HIGH) I Power cord See "Connecting the AV Receiver" for connection information (➔ 16 - Onkyo HT-S7300 | Owner Manual - Page 10
adjust the volume of the subwoofer. D LINE INPUT (➔ 17) This RCA input should be connected to the SUBWOOFER PRE OUT on the AV receiver with increasing or decreasing the subwoofer output level on the AV receiver (➔ 42). Front, Center, Surround and Surround Back Speakers ■ HTP-680 (SKF-680, SKC-680, - Onkyo HT-S7300 | Owner Manual - Page 11
keyhole slots can be used to wall-mount the speaker. See "Wall Mounting" for mounting instructions (➔ 14). C Speaker terminals These push terminals are for connecting the speaker to the HT-R680 with the supplied speaker cables. The supplied speaker cables are color-coded for easy identification - Onkyo HT-S7300 | Owner Manual - Page 12
AV Receiver B C *1 D E B F G H C I J K D L*2 M N*3 E O To control the AV receiver, press RECEIVER to select Receiver mode. You can also use the remote controller to control Onkyo LAYOUT button (➔ 26) E Arrow R/X/F/S and ENTER buttons F SETUP button (➔ 38) G LISTENING MODE buttons (MOVIE/TV, MUSIC, - Onkyo HT-S7300 | Owner Manual - Page 13
room, and choose the one that provides the most satisfying results. B C Front speakers (SKF-680/780) These output the overall sound. Their role in a home theater is to provide a solid anchor for the sound handles the bass sounds of the LFE (Low-Frequency Effects) channel. The volume and quality of - Onkyo HT-S7300 | Owner Manual - Page 14
on a flat, level, and stable floor. • After you attach the speaker bases, make sure that the speakers stand upright and are stable. Center Speaker To mount the center speaker horizontally, use the two keyhole slots shown to hang each speaker on two screws that are securely screwed into the wall - Onkyo HT-S7300 | Owner Manual - Page 15
shown. (We recommend that you consult a home installation professional.) Wall Using the Stoppers for a More Stable Platform We recommend using the provided stoppers to achieve the best possible sound from your speakers. The stoppers prevent the speakers from moving, providing a more stable platform - Onkyo HT-S7300 | Owner Manual - Page 16
and solid bass. To get the best from your surround sound system, you need to set the speaker settings. You can do this automatically (➔ 28) or manually (➔ 40). Speaker Connection Precautions Read the following before connecting your speakers: • You can connect speakers with an impedance of between - Onkyo HT-S7300 | Owner Manual - Page 17
RCA cable, connect the subwoofer's LINE INPUT jack to your AV receiver's SUBWOOFER PRE OUT jack. Note • The front high speakers can also be connected to the SURR BACK OR FRONT HIGH SPEAKERS terminals. When doing so, set En "Surr Back/Front High" in Speaker Setup to "Front High" (➔ 40). 17 - Onkyo HT-S7300 | Owner Manual - Page 18
PCM input signal is 32/44.1/48/88.2/96 kHz. Even 176.4/192 kHz is effective in case of the HDMI connection. Note • The AV receiver does not support SCART plugs. • The AV receiver's optical digital jacks have shutter-type covers that open when an optical plug is inserted and close when it's removed - Onkyo HT-S7300 | Owner Manual - Page 19
from speakers of Q-compatible TV, by controlling the AV receiver's volume, the AV receiver's speakers will produce sound while the TV's speakers are muted. To stop the AV receiver's speakers producing sound, change the settings, change your TV's settings, or turn down the AV receiver's volume. En - Onkyo HT-S7300 | Owner Manual - Page 20
setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receiver's display when changing settings preamp. See your turntable's manual for details. • When you components in the main room; you can listen to - Onkyo HT-S7300 | Owner Manual - Page 21
either one to the AV receiver. The other jack is for connecting additional V-capable components. • Connect only Onkyo components to V jacks. Connecting other manufacturer's components may cause a malfunction. • Some components may not support all V functions. Refer to the manuals supplied with your - Onkyo HT-S7300 | Owner Manual - Page 22
for use, you'll need to tune into a radio station and position the antenna to achieve the best possible reception. • Keep the AM loop antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords. Tip • If you cannot achieve good reception with the supplied indoor FM - Onkyo HT-S7300 | Owner Manual - Page 23
. Use the following sections as a guide. The on-screen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receiver's display when changing settings. Video Connection Formats Video component can - Onkyo HT-S7300 | Owner Manual - Page 24
on, the display lights, and the STANDBY indicator goes off. Turning Off Press ON/STANDBY on the front panel or the remote controller. The AV receiver will enter Standby mode. To prevent any loud surprises when you turn on the AV receiver, always turn down the volume before you turn it off. En 24 - Onkyo HT-S7300 | Owner Manual - Page 25
is connected to the HDMI OUT. If your TV is connected to the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receiver's display when changing settings. This manual describes the procedure using the remote controller unless otherwise specified. ■ Adjusting the subwoofer volume level Use the - Onkyo HT-S7300 | Owner Manual - Page 26
SP LAYOUT repeatedly. `Speaker Layout:FH: The sound from front high speakers is output by priority. `Speaker Layout:SB: The sound from surround back speakers is output by priority. Setting the Display Brightness You can adjust the brightness of the AV receiver's display. Press RECEIVER followed by - Onkyo HT-S7300 | Owner Manual - Page 27
and listening mode, not all channels shown here output the sound. *4 When you have entered a custom name in "Name Edit" (➔ 45), the input source is displayed with that name. But even if not, the component name may be displayed if the AV receiver receives it via HDMI connection (➔ 19). *5 For the - Onkyo HT-S7300 | Owner Manual - Page 28
to which the AV receiver is connected. 2 Set the speaker setup microphone at the Main Listening Position B, and connect it to the SETUP MIC jack. SETUP MIC jack Speaker setup microphone Using Audyssey 2EQ Using Audyssey 2EQ to create a listening environment in your home theater that all listeners - Onkyo HT-S7300 | Owner Manual - Page 29
on the "Review Speaker Configuration" screen as "No", increase the subwoofer's volume to the half-way point, set it to its highest crossover frequency, and then try running Audyssey 2EQ Room Correction and Speaker Setup again. Note that if the volume is set too high and the sound distorts, detection - Onkyo HT-S7300 | Owner Manual - Page 30
can store your favorite stations as presets for quick selection. This model changes FM/AM frequency in 200/10kHz (or 50/9kHz) steps. Listening to the radio band changes between AM and FM. Band Frequency (Actual display depends on the country.) ■ Manual tuning mode 1 Press TUNING MODE so that the - Onkyo HT-S7300 | Owner Manual - Page 31
through 40. 4 Press MEMORY again to store the station or channel. The station or channel is stored and the preset number stops flashing. Repeat this procedure instead of the band and frequency. Selecting Presets To select a preset, use PRESET F/S on the AV receiver, or the remote controller's CH - Onkyo HT-S7300 | Owner Manual - Page 32
. 1 Use the input selector buttons to select the source that you want to record. You can watch the source while recording. The AV receiver's MASTER VOLUME control has no effect on recording. 2 On your recorder, start recording. 3 On the source component, start playback. If you select another input - Onkyo HT-S7300 | Owner Manual - Page 33
headphones is connected, you can select the following listening modes: Mono, Direct, and Stereo. • The listening modes cannot be used while you are listening to sound through your TV speakers coming from components connected to the AV receiver ("TV Sp On" appears on the front panel). En 33 - Onkyo HT-S7300 | Owner Manual - Page 34
AV receiver's listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound. Explanatory Notes Speaker illustrations are based on HTP-680. BC D JK SP LAYOUT LISTENING MODE G EF HI B C Front speakers D Center speaker - Onkyo HT-S7300 | Owner Manual - Page 35
sound processing. The "Sp Config" (presence of speakers), "Sp Distance" and "A/V Sync" settings are enabled, but much of the processing set via AUDIO is disabled. See "Advanced Setup" for more details (➔ 38). " 4 % ' ( ) Stereo Sound material when height channel speaker outputs are present. - Onkyo HT-S7300 | Owner Manual - Page 36
the input source is output without surround-sound % processing. "Sp Config" (presence of speakers), "Crossover", "Sp DisD o l b y c D i o P P tance", "A/V Sync" and much of the processing set via AUDIO are enabled. Dolby Digital Plus*5 See "Advanced Setup" for more details (➔ 38). % Do l b y cD - Onkyo HT-S7300 | Owner Manual - Page 37
the Blu-ray Discs, Dolby Digital is used in a 3.1/5.1-channel speaker system. *6 AV receiver can input the DSD signal from HDMI IN. Setting the output setting on the player side to PCM might obtain a better sound according to the player. In that case, set the output setting on the player side to PCM - Onkyo HT-S7300 | Owner Manual - Page 38
and use F/S to change the setting. Press SETUP to close the menu. Press RETURN to return to the previous menu. Note • This procedure can also be performed on the AV receiver by using SETUP, arrow buttons, and ENTER. • During Audyssey 2EQ® Room Correction and Speaker Setup, messages, etc., that are - Onkyo HT-S7300 | Owner Manual - Page 39
Out You can specify the output resolution for the HDMI OUT and have the AV receiver upconvert the picture resolution as necessary to match the resolution supported by your TV. ■ Resolution ` Through: Select this to pass video through the AV receiver at the same resolution and with no conversion - Onkyo HT-S7300 | Owner Manual - Page 40
HDMI output Speaker Setup Main menu Speaker Setup Some of the settings in this section are set automatically by Audyssey 2EQ® Room Correction and Speaker Setup function (➔ 28). Here you can check the settings made by Audyssey 2EQ Room Correction and Speaker Setup function, or set them manually - Onkyo HT-S7300 | Owner Manual - Page 41
This setting is set automatically by Audyssey 2EQ® Room Correction and Speaker Setup function (➔ 28). With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. Specify "Full Band" for speakers that can output low frequency bass sounds adequately - Onkyo HT-S7300 | Owner Manual - Page 42
Level Calibration Audio Adjust This setting is set automatically by Audyssey 2EQ® Room Correction and Speaker Setup function (➔ 28). Here you can adjust the level of each speaker with the built-in test tone so that the volume of each speaker is the same at the listening position. ■ Left, Front - Onkyo HT-S7300 | Owner Manual - Page 43
, if you're using a center speaker, the center channel sound is output by only the center speaker. (If you're not using a center speaker, the center channel sound will be distributed to the front left and right speakers to create a phantom center). This setting controls the front left, right, and - Onkyo HT-S7300 | Owner Manual - Page 44
each speaker level must be adjusted so that -30 dBFS band-limited (500 Hz to 2000 Hz) pink noise produces 75 dB sound pressure level at the listening position. A home theater system automatically cali- brated by Audyssey 2EQ will play at reference level when the master volume control is set to - Onkyo HT-S7300 | Owner Manual - Page 45
Audyssey Dynamic Volume® Audyssey Dynamic Volume solves the problem of large variations in volume level between television programs, commercials, and between the soft and loud passages of movies. Dynamic Volume looks at the preferred volume setting by the user and then monitors how the volume of - Onkyo HT-S7300 | Owner Manual - Page 46
source to the appropriate progressive signal and reproduces the natural quality of the original picture. When the "Film Mode" setting is set to "Auto", the AV receiver automatically detects the picture source and in either "3 : 2" or "2 : 2". However, there may be times when you will get a better - Onkyo HT-S7300 | Owner Manual - Page 47
the AV receiver has been set to Standby. Main sound to "PORT" selector. 2 Use R/X to select the signal format that you want to set Source With this setting, you can specify the default listening mode for 2-channel (2/0) stereo sources (input via HDMI). ■ DTS/DTS-ES/DTS-HD With this setting, you can - Onkyo HT-S7300 | Owner Manual - Page 48
Español, Italiano, Nederlands, Svenska, ʕ˖ This setting determines the language used for the onscreen setup menus. ■ Remote ID ` 1, 2, or 3 When several Onkyo components are used in the same room, their remote ID codes may overlap. To differentiate the AV receiver from the other components, you can - Onkyo HT-S7300 | Owner Manual - Page 49
up the AV receiver's volume control, the sound will be output by the AV receiver's front left and right speakers. To stop the AV receiver's speakers producing sound, change the settings, change your TV's settings, or turn down the AV receiver's volume. ■ Lip Sync ` Disable: HDMI lip sync disabled - Onkyo HT-S7300 | Owner Manual - Page 50
a TV program. • Refer to the connected component's instruction manual for details. ■ TV Control ` Off: TV Control disabled. ` On: TV Control enabled. Set to "On" when you want to control the AV receiver from an Q-compatible TV that is connected to HDMI. Note • Do not assign the component connected - Onkyo HT-S7300 | Owner Manual - Page 51
AV receiver is muted. • Speakers that are set to "No" or "None" in the "Speaker Configuration" (➔ 41) cannot be adjusted. Audyssey Settings ■ Dynamic EQ See "Dynamic EQ" in "Source Setup" (➔ 44). ■ Dynamic Volume See "Dynamic Volume" in "Source Setup of the original sound designer, and movie theater. - Onkyo HT-S7300 | Owner Manual - Page 52
ENTER again allows you to return to the "Audio Selector" setting. Normally, the AV receiver detects the signal format automatically. However, if you experience either of the following issues when playing PCM or DTS material, you can manually set the signal format to PCM or DTS. If the beginnings of - Onkyo HT-S7300 | Owner Manual - Page 53
to the AV receiver's FRONT HIGH OR ZONE 2 SPEAKERS L/R terminals. AV receiver Main room TV AV receiver Zone 2 IN R L Receiver/ integrated amp Zone 2 RL Note • The Zone 2 volume must be set on the Zone 2 amp. Note • With this setup, the Zone 2 volume is controlled by the AV receiver. En - Onkyo HT-S7300 | Owner Manual - Page 54
connected your Zone 2 speakers to the AV receiver, as explained in "Connecting Your Zone 2 Speakers Directly to the AV receiver" (➔ 53), you must set the "Front High/Zone2" setting to "Zone2". Main menu Speaker Setup 1 In the "Speaker Setup" menu, select "Speaker Settings", and then press ENTER - Onkyo HT-S7300 | Owner Manual - Page 55
volume. ■ Operating on the AV receiver 1 Press ZONE 2 (the ZONE 2 indicator and Zone 2 selector on the display flashes). 2 Use -/+ within 8 seconds to adjust the volume. If your Zone 2 speakers are connected to a receiver 2 SPEAKERS L/R terminals. Digital input sources are not output. If no sound is - Onkyo HT-S7300 | Owner Manual - Page 56
standby mode slightly increases. • You can control your iPod when PORT is selected as the input source. • See the RI Dock's instruction manual 58 for more information. *1 To use V (Remote Interactive), you must make an analog audio connection (RCA) between the AV receiver and the RI Dock. En 56 - Onkyo HT-S7300 | Owner Manual - Page 57
://www.onkyo.com Before using the Onkyo Dock components, update your iPod with the latest software, available from the Apple web site. UP-A1 Dock With the supplied UP-A1 Dock, you can easily play the music, photo, or movie stored on your Apple iPod through the AV receiver and enjoy great sound. You - Onkyo HT-S7300 | Owner Manual - Page 58
to your iPod. RI Dock RI Dock is sold separately. For supported iPod models, see the instruction manual of the RI Dock. With the RI Dock, you can easily play the music stored on your Apple iPod through the AV receiver and enjoy great sound, and watch iPod slideshows and videos on your TV. In - Onkyo HT-S7300 | Owner Manual - Page 59
models, generations and RI Docks, certain buttons may not work as expected. • For detailed operation of the iPod, please refer to the instruction manual of RI Dock. *1 This button does not turn the Onkyo the playback will be continued even if the AV receiver is turned off. • In Extended mode (see - Onkyo HT-S7300 | Owner Manual - Page 60
CD player (➔ 62) PORT Onkyo Universal Port Option (➔ 58) Looking up for Remote Control Code You can look up for appropriate remote control code from on-screen setup menu. This setting can not be carried out by using the AV receiver's display. 1 Press RECEIVER followed by SETUP. The main menu appears - Onkyo HT-S7300 | Owner Manual - Page 61
at the time of printing, but are subject to change. Remote Control Codes for Onkyo Components Connected via V Onkyo components that are connected via V are controlled by pointing the remote controller at the AV receiver, not the component. This allows you to control components that are out of view - Onkyo HT-S7300 | Owner Manual - Page 62
code for controlling a component that supports the Q*1 (limited to some models). The component must be able to receive remote control commands via Q and be connected to the AV receiver via HDMI. *1 The Q supported by the AV receiver is the CEC system control function of the HDMI standard. En 62 - Onkyo HT-S7300 | Owner Manual - Page 63
✔ ✔ C , INPUT, ✔ TV VOL R/X D GUIDE ✔ ✔✔ TOP MENU ✔ E R/X/F/S ENTER ✔✔ ✔✔ ✔ F SETUP ✔✔ ✔✔ ✔ G 1 ✔ , , 3 H SEARCH *1 The Q function is not supported. The Q supported by the AV receiver is the CEC system control function of the HDMI standard. *2 These buttons function as - Onkyo HT-S7300 | Owner Manual - Page 64
Make sure that the input source is properly selected. 25 Make sure that the speaker cables are not shorting. 16 Check the volume. The AV receiver is designed for - home theater enjoyment. It has a wide volume range, allowing precise adjustment. If the MUTING indicator is flashing on the display - Onkyo HT-S7300 | Owner Manual - Page 65
volume possible may be reduced. Note that the individual speaker volume levels are set automatically after the Audyssey 2EQ® Room Correction and Speaker Setup from DTS to PCM, because the AV receiver does not switch formats immediately, you may not hear any sound, in which case you should stop your - Onkyo HT-S7300 | Owner Manual - Page 66
, connected. 56 If your TV is connected to the HDMI OUT, select 39 in the "HDMI Input" setup to watch composite video, and component video sources. If sure to set the same ID on both the AV receiver 48 and remote controller. ■ Can't control other components If it's an Onkyo component, make - Onkyo HT-S7300 | Owner Manual - Page 67
the component and AV receiver, even if they are connected digitally. ■ The functions System On/Auto Power On and Direct Change don't work for components connected via V These functions don't work when Zone 2 is turned 21 on. ■ When performing "Audyssey 2EQ® Room Correction and Speaker Setup", the - Onkyo HT-S7300 | Owner Manual - Page 68
least five seconds, and then plug it back in again. Onkyo is not responsible for damages (such as CD rental fees set the AV receiver to Standby. Important Note Regarding Video Playback The AV receiver can upconvert component video and composite video sources for display on a TV connected to the HDMI - Onkyo HT-S7300 | Owner Manual - Page 69
mm × 151.5 mm × 328.5 mm Weight 8.6 kg (19.0 lbs.) ■ HDMI Input Output Video Resolution Audio Format Supported IN 1, IN 2, IN 3, IN 4 OUT 1080p Dolby True HD, DTS Master Audio, DVD-Audio, DSD 3D, Audio Return Channel, Deep Color, x.v.Color, LipSync, CEC ■ Video Inputs Component Composite IN - Onkyo HT-S7300 | Owner Manual - Page 70
7.1ch Home Theater Speaker Package (HTP-680) ■ Powered Subwoofer (SKW-770) Type Bass-reflex Input sensitivity/Impedance 140 mV/20 kΩ Maximum output power 290 W (Dynamic power) Frequency response 25 Hz to 150 Hz Cabinet capacity 37 L (1.3 cubic feet) Dimensions (W × H × D) 10-13/16" × 19- - Onkyo HT-S7300 | Owner Manual - Page 71
7.1ch Home Theater Speaker Package (HTP-780) ■ Powered Subwoofer (SKW-780) Type Bass-reflex Input sensitivity/Impedance 140 mV/20 kΩ Maximum output power 290 W (Dynamic power) Frequency response 25 Hz to 150 Hz Cabinet capacity 37 L (1.3 cubic feet) Dimensions (W × H × D) 10-13/16" × 19- - Onkyo HT-S7300 | Owner Manual - Page 72
PC are not supported. • The HDMI audio signal (sampling rate, bit length, etc.) may be restricted by the connected source component. If the picture is poor or there's no sound from a component connected via HDMI, check its setup. Refer to the connected component's instruction manual for details. En - Onkyo HT-S7300 | Owner Manual - Page 73
TV, Player, or Recorder Q, which stands for Remote Interactive over HDMI, is the name of the system control function found on Onkyo components. The AV receiver can be used with CEC (Consumer Electronics Control), which allows system control over HDMI and is part of the HDMI standard. CEC provides - Onkyo HT-S7300 | Owner Manual - Page 74
be possible depending on the player models.) • Even if you set to output audio on the TV speakers, audio will be output from the speakers connected to the AV receiver when you adjust the volume or switch the input on the AV receiver. To output audio from the TV speakers, re-do the operations on the - Onkyo HT-S7300 | Owner Manual - Page 75
Video Resolution Chart The following tables show how video signals at different resolutions are output by the AV receiver. ✔: Output Input HDMI Component Composite Output HDMI Component Composite 1080p 1080i 720p 480p 480i 1080p 1080i 720p 480p 480i 480i 1080p ✔ 1080i ✔ ✔ ✔ 720p ✔ ✔ - Onkyo HT-S7300 | Owner Manual - Page 76
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8163 ONKYO U.S.A. CORPORATION 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 800-229-1687, 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/ ONKYO EUROPE ELECTRONICS
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
 |
 |
7.1ch Home Theater System
HT-S7300
AV Receiver (HT-R680)
Speaker Package (HTP-780)
Universal Port Option Dock for iPod
®
(UP-A1)
HT-S6300
AV Receiver (HT-R680)
Speaker Package (HTP-680)
Universal Port Option Dock for iPod
®
(UP-A1)
Instruction Manual
Thank you for purchasing an Onkyo 7.1ch Home
Theater System. Please read this manual thoroughly
before making connections and plugging in the unit.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new 7.1ch Home Theater
System.
Please retain this manual for future reference.
Contents
Introduction
...................................
2
Connections
.................................
14
Turning On & Basic Operations
......
24
Advanced Operations
.................
38
Controlling iPod & Other
Components
............................
56
Others
...........................................
64
E
n